ANSI TIA EIA 455-57B-1994 Preparation and Examination of Optical Fiber Endface Testing Purposes《光纤端面测试目的的制定和检验》.pdf

《ANSI TIA EIA 455-57B-1994 Preparation and Examination of Optical Fiber Endface Testing Purposes《光纤端面测试目的的制定和检验》.pdf》由会员分享，可在线阅读，更多相关《ANSI TIA EIA 455-57B-1994 Preparation and Examination of Optical Fiber Endface Testing Purposes《光纤端面测试目的的制定和检验》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、 TIASTANDARDFOTP-57Preparation and Examination of OpticalFiber Endface for Testing PurposesTIA-455-57-B(Revision of EIA/TIA-455-57-A)May 1994TELECOMMUNICATIONS INDUSTRY ASSOCIATIONRepresenting the telecommunications industry inassociation with the Electronic Industries Alliance ANSI/TIA/EIA-455-57-B

2、-1994Approved: May 12, 1994Reaffirmed: September 14, 2000 Reaffirmed: May 10, 2005Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE TIA Engineering Standards and Publicatio

3、ns are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need

4、. The existence of such Standards and Publications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use b

5、y Non-TIA members, either domestically or internationally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whateve

6、r to parties adopting the Standard or Publication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determ

7、ine the applicability of regulatory limitations before its use. (From Standards Proposal No. 3-3036-RF2, formulated under the cognizance of the TIA FO-4.2 Subcommittee on Optical Fibers and Cables). Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Standards and Technology Department 2500 Wilson

8、Boulevard Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call Global Engineering Documents, USA and Canada (1-800-854-7179) International (303-397-7956) or search online at http:/www.tiaonline

9、.org/standards/search_n_order.cfm All rights reserved Printed in U.S.A. Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE OF COPYRIGHT This document is copyrighted by the T

10、IA. Reproduction of these documents either in hard copy or soft copy (including posting on the web) is prohibited without copyright permission. For copyright permission to reproduce portions of this document, please contact TIA Standards Department or go to the TIA website (www.tiaonline.org) for de

11、tails on how to request permission. Details are located at: http:/www.tiaonline.org/about/faqDetail.cfm?id=18 OR Telecommunications Industry Association Standards (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form;

12、(c) the Document may be amended, modified or changed in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TI

13、A makes no search or investigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims a

14、ny obligation to investigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are re

15、asonable or non-discriminatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, ins

16、pect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIAT

17、ENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NON-INFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WIT

18、H ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO AN

19、Y USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLI

20、GENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. Copyright Telecommunications Industry A

21、ssociation Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-455-57-BiFOTP-57Preparation and examination of optical fiber endface for testing purposesContentsForeword iii1 Introduction .12 Normative references13 Apparatus24 S

22、ampling and specimens45 Procedure .46 Calculations or interpretation of results.67 Documentation68 Specification information.79 Figures, tables charts, etc. 8Annex A (normative) Laser reflection fiber end inspection technique11Annex B (informative) Comparison between this FOTP and IEC or ITU/TSrequi

23、rements.13References.14Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-455-57-BiiThis page left blank.Copyright Telecommunications Industry Association Provided by IHS under

24、 license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-455-57-BiiiFOTP-57Preparation and examination of optical fiber endface for testing purposesForeword(This Foreword is informative only and is not part of this Standard.)From TIA Project No. 3036, f

25、ormulated under the cognizance of TIA FO-6.6,Subcommittee on Fibers and Materials.This FOTP is part of the series of test procedures included within RecommendedStandard EIA/TIA-455.There are 2 annexes, 1 of them normative and 1 informative.Key words: optical fiber, endface preparation, testing, clea

26、vingCopyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-455-57-BivThis page left blankCopyright Telecommunications Industry Association Provided by IHS under license with EIANot

27、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-455-57-B11 Introduction1.1 IntentThis procedure provides guidelines for acceptable optical fiber endfaceappearance and defines the techniques that are commonly employed to obtainsuch appearance. This procedure is int

28、ended to promote uniformity in fiber endpreparation quality for testing purposes only and does not address issuesassociated with endface preparation and examination for the purposes ofpermanent termination (i.e., connectorization and splicing). This FOTP is notintended to require examination of ever

29、y fiber end, nor is it intended to establishfirm requirements, and is made available only to provide guidelines for variouslevels of end quality that may be called out in other FOTPs. Lastly, the intent ofthis method shall not be confused with the intent of FOTP-179, which isconcerned primarily with

30、 the comparison of relative results.1.2 HazardsThe procedure may involve the use of certain hazardous materials, operationsand equipment. It is the responsibility of whoever uses this procedure toestablish appropriate safety practices and to determine the applicability ofregulatory limitations prior

31、 to use. Note, in particular, that some fluids used maybe flammable or may constitute health hazards, or both. Use proper precautionsduring handling and during the balance of the procedure. Constant, prolonged orexcess exposure to solvents such as Freon, 1-1-1 trichloroethane, methylenechloride and

32、methyl isobutyl ketone may act as a carcinogen or damage internalorgans. Use solvents in a well-ventilated area and avoid skin contact as astandard precaution. Consult safety data sheets for these materials.2 Normative referencesTest or inspection requirements may include, but are not limited to, th

33、e followingreferences:EIA/TIA-455-A, Standard Test Procedure for Fiber Optic Fibers, Cables,Transducers, Sensors, Connecting and Transmitting Devices, and Other FiberOptic ComponentsFOTP-13 (RS-455-13), Visual and Mechanical Inspection of Fibers, Cables,Connectors, and/or Fiber Optic DevicesCopyrigh

34、t Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-455-57-B2FOTP-179 (EIA-455-179), Inspection of Cleaved Fiber End Faces byInterferometryNQ-EIA-5460000, Generic Specification for a Fi

35、eld Portable Optical InspectionDevice3 ApparatusA wide variety of end preparation equipment is available, designed to give flatendfaces, perpendicular to the fiber axis. Any of this equipment is acceptable,provided the end angle and facial condition of the prepared fiber are of sufficientquality to

36、ensure the necessary accuracy and precision required for the particularquality control measurement to be made. When special equipment is required, itshall be specified in the affected FOTP. The following guidelines may be usefulin deciding upon equipment to be used:3.1 Cleaving, cutting and slicing

37、devicesCleaving, cutting and slicing devices are usually of the scribe-and-break variety,but are not necessarily restricted to this category. Tension on the fiber is usuallyapplied, either by tensile load or a bend, some time during or after the impositionof the scribing operation3.2 Mechanical stri

38、pperA mechanical stripping device may be employed to remove fiber coating if thechemical cleaning fluids (refer to 3.4) are not used. Note, however, that somefiber manufacturers have fiber coatings that are not removable by mechanicalmeans.3.3 Fiber polishing equipmentEnd-polishing equipment may be

39、used, although it is often unnecessary for thepurpose of making optical measurements.Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-455-57-B33.4 Cleaning fluidsA cleaning f

40、luid may be required, its composition dependent upon the chemistryof the fiber itself and its coating (e.g., acetone, isopropyl alcohol and othersolvents have been successfully used with some fibers).CAUTION: Refer to 1.23.5 MicroscopeUse an optical microscope, such as the one specified in EIA-54600

41、00. Typicalinspections can be accomplished with magnifications as prescribed in FOTP-13.Use a magnification of 200X for U.S. military applications or for rigorousexamination of fibers with a diameter of less than or equal to 140 m.3.6 Fiber positioning and holding equipmentA means of positioning the

42、 fiber such that the fiber axis is perpendicular to theplane of cleaving, cutting or polishing is normally used during cleaving, cuttingand polishing operations. Such fixtures shall be fabricated of materials that willnot degrade the acceptable endface quality. In positioning operations, positioning

43、means may require use of curing fluids.3.1 InterferometerThe physical profile of fiber endfaces can be measured with an interferometerconfigured to compare fiber endfaces to an optical flat (e.g., refer to FOTP-179).Such devices typically display a “contour map” of the fiber endface. End-anglesare c

44、omputed from the number of fringes observed across the image of the fiberface (although this is strictly valid only for straight, parallel fringe patterns).Interferometers specifically designed for measuring fiber endfaces arecommercially available. For critical measurements requiring flat, perpendi

45、cularendfaces, the interferometer is recommended. End-angles as small as 0.1degree and surface features with heights/depths of about 0.2 to 0.3 m can beaccurately measured.3.8 Other equipmentSupplementary equipment may be used as required for auxiliary illumination,positioning, handling, acceleratin

46、g fluid curing times, examination of the preparedend, etc. (e.g., local temperature changing apparatus may be utilized, liquidsmay be used during polishing as carriers, lubricant, etc.).Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduct

47、ion or networking permitted without license from IHS-,-,-TIA-455-57-B44 Sampling and specimensA sample consists of the fiber or cable being prepared. Remove all protectivejacketing and buffer materials from the fiber end area, as required.5 Procedure5.1 ConditionsThis procedure may be conducted unde

48、r factory ambient atmospheric conditionsor applicable field application environmental conditions as required. In case ofany dispute, repeat the procedure using Standard Atmospheric Conditionsrequired by EIA/TIA-455-A, clause 6.5.2 MethodsSelect the appropriate end preparation method from the following as determinedby fiber type and/or application. Examination is performed according to 5.3.5.2.1 Procedure A - Fiber cleaving, cutting or slicingCleaving, cutting or slicing, as appropriate, is accomplished using suitableapparatus (refer to clau