ANSI TIA EIA 455-221-2001 Optical Fiber Amplifiers - Basic Specification - Part 5 -1 Test Method for Reflectance Parameters - Optical Spectrum Analyzer《光纤放大器.基本规范.第5-1部分 反射参数的测试方法..pdf

《ANSI TIA EIA 455-221-2001 Optical Fiber Amplifiers - Basic Specification - Part 5 -1 Test Method for Reflectance Parameters - Optical Spectrum Analyzer《光纤放大器.基本规范.第5-1部分 反射参数的测试方法..pdf》由会员分享，可在线阅读，更多相关《ANSI TIA EIA 455-221-2001 Optical Fiber Amplifiers - Basic Specification - Part 5 -1 Test Method for Reflectance Parameters - Optical Spectrum Analyzer《光纤放大器.基本规范.第5-1部分 反射参数的测试方法..pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、ANSI/TIA/EIA-455-221-2001 Approved: December 20, 2001 TIA/EIA STANDARD FOTP-22 1 IEC 6 1290-5- 1 Optical Fibre Amplifiers - Basic Specification Part 5-1 : Test Methods for Reflectance Parameters - Optical Spectrum Analyzer TIA/EIA-455-221 DECEMBER 2001 TELECOMMUNICATIONS INDUSTRY ASSOCIATION Represe

2、nting the telecommunications industry in association with the Electronic Industries Alliance Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE TIA/EIA Engineering Standards

3、 and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his pa

4、rticular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of TIA/EIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their volunta

5、ry use by those other than TIA/EIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by TIA/EIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA/EIA does not assume any liab

6、ility to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standar

7、d to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. These Materials are subject to copyright claims of IEC, ANSI, and TIA. No part of this publication may be reproduced in any form, including an electronic retrieval syst

8、em, without the prior written permission of TIA. All requests pertaining to the FOTP-223-IEC 61291-2: Optical Fibre Amplifiers - Part 2 :Digital Applications - Performance Specification Template Standard should be submitted to TIA. (From Standards Proposal No. 3-0026, formulated under the cognizance

9、 of the TIA FO-2.7 Subcommittee on Optically Amplified Devices, Subsystems, and Systems.) Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION 200 i Standards and Technology Department 2500 Wilson Boulevard Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of EIA ELECTRONIC INDUSTRIE

10、S ALLIANCE STANDARDS and ENGINEERING PUBLICATIONS or call Global Engineering Documents, USA and Canada (1 -800-854-7 179) International (303-397-7956) All rights reserved Printed in U.S.A. Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reprod

11、uction or networking permitted without license from IHS-,-,-Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE OF DISCLAIMER AND LIMITATION OF LIABILITY The document to whic

12、h this Notice is affixed has been prepared by one or more Engineering Committees of the Telecommunications Industry Association (“TIA”). TIA is not the author of the document contents, but publishes and claims copyright to the document pursuant to licenses and permission granted by the authors of th

13、e contents. TIA Engineering Committees are expected to conduct their affairs in accordance with the TIA Engineering Manual (“Manual”), the current and predecessor versions of which are available at http:/www.tiaonline.orZr/standards/sfZr/engineering manual.ch. TIAS function is to administer the proc

14、ess, but not the content, of document preparation in accordance with the Manual and, when appropriate, the policies and procedures of the American National Standards Institute (“ANSI”). THE USE OR PRACTICE OF CONTENTS OF THIS DOCUMENT MAY INVOLVE THE USE OF INTELLECTUAL PROPERTY RIGHTS (“IPR), INCLU

15、DING PENDING OR ISSUED PATENTS, OR COPYRIGHTS, OWNED BY ONE OR MORE PARTIES. TIA MAKES NO SEARCH OR INVESTIGATION FOR IPR. WHEN IPR CONSISTING OF PATENTS AND PUBLISHED PATENT APPLICATIONS ARE CLAIMED AND CALLED TO TIAS ATTENTION, A STATEMENT FROM THE HOLDER THEREOF IS REQUESTED, ALL IN ACCORDANCE WI

16、TH THE MANUAL. TIA TAKES NO POSITION WITH REFERENCE TO, AND DISCLAIMS ANY OBLIGATION TO INVESTIGATE OR INQUIRE INTO, THE SCOPE OR VALIDITY OF ANY CLAIMS OF IPR. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CON

17、TENTS, ITS FITNESS OR APPROPRIATENESS FORA PARTICULAR PURPOSE PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR R

18、EGULATION. OR USE, ITS MERCHANTABILITY AND ITS NON-INFRINGEMENT OF ANY THIRD TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENT

19、IAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGE

20、S IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from

21、IHS-,-,-61290-5-1 O IEC:2000 TIA-455-221 CONTENTS Page 1 2 3 4 5 6 7 Scope and object . . Normative references . . . . 1 . . 3 Procedure . . 3 . 3 5.1.1 Calibration . .4 5.1.2 OFA reflectance measurement . 5 5.2 Output reflectance . . 5 Calculation . . . 5 6.2 Output reflectance . Test results . 7.1

22、 Maximum and minimum input reflectance 7.2 Output reflectance . I Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-61290-5-1 O IEC:2000 TIA-455-221 II Copyright Telecommunication

23、s Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-61290-5-1 O IEC:2000 TIA-455-221 FDIS 86C/270/FD I S INTERNATIONAL ELECTROTECHNICAL COMMISSION Report on voting 86C/272/RVD OPTICAL FIBRE AMPLIFIERS - BASIC

24、 SPECIFICATION - Part 5-1 : Test methods for reflectance parameters - Optical spectrum analyser FOREWORD The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of th

25、e IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, the IEC publishes International Standards. Their preparation is entrusted to technical committees; any IEC National Com

26、mittee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization for Standardization (ISO)

27、in accordance with conditions determined by agreement between the two organizations. The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation fro

28、m all interested National Committees. The documents produced have the form of recommendations for international use and are published in the form of standards, technical specifications, technical reports or guides and they are accepted by the National Committees in that sense. In order to promote in

29、ternational unification, IEC National Committees undertake to apply IEC International Standards transparently to the maximum extent possible in their national and regional standards. Any divergence between the IEC Standard and the corresponding national or regional standard shall be clearly indicate

30、d in the latter. The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with one of its standards. Attention is drawn to the possibility that some of the elements of this International Standard may be the subje

31、ct of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61290-5-1 has been prepared by subcommittee 86C: Fibre optic systems and active devices, of IEC technical committee 86: Fibre optics. This standard should be read in c

32、onjunction with IEC 61291-1. The text of this standard is based on the following documents: Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. Annex A is for information only. This publication has been drafted in accord

33、ance with the ISO/IEC Directives, Part 3. The committee has decided that the contents of this publication will remain unchanged until 2006. At this date, the publication will be reconfirmed; . III Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleN

34、o reproduction or networking permitted without license from IHS-,-,-61290-5-1 O IEC:2000 TIA-455-221 withdrawn; amended. replaced by a revised edition, or iv Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted

35、without license from IHS-,-,-61290-5-1 O IEC:2000 TIA-455-221 INTRODUCTION As far as can be determined, this is the first International Standard on this subject. The technology of optical fibre amplifiers is quite new and still emerging, hence amendments to and new editions of this standard can be e

36、xpected. Each abbreviation introduced in this standard is explained in the text at least the first time it appears. However, for an easier understanding of the whole text, a list of all abbreviations used in this standard is given in annex A. V Copyright Telecommunications Industry Association Provi

37、ded by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-61290-5-1 O IEC:2000 TIA-455-221 vi Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted withou

38、t license from IHS-,-,-61290-5-1 O IEC:2000 TIA-455-221 OPTICAL FIBRE AMPLIFIERS - BASIC SPECIFICATION - Part 5-1 : Test methods for reflectance parameters - Optical spectrum analyser 1 Scope and object This International Standard applies to optical fibre amplifiers (OFAs) using active fibres, conta

39、ining rare-earth dopants, presently commercially available. The object of this standard is to establish uniform requirements for accurate and reliable measurements, by means of the optical spectrum analyzer test method, of the following OFA parameters, as defined in clause 3 of IEC 61291-1: a) maxim

40、um input reflectance; b) minimum input reflectance; c) output reflectance. NOTE All numerical values followed by ($) are currently under consideration 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part

41、 of IEC 61290. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of IEC 61290 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicat

42、ed below. For undated references, the latest edition of the normative document referred to applies. Members of IEC and IS0 maintain registers of currently valid International Standards. IEC 61291-1:1998, Opfical fibre amplifiers - Parf 1: Generic specificafion NOTE A list of informative references i

43、s given in the bibliography. 3 Apparatus A scheme of the measurement set-up is given in figure I. The test equipments listed below, with the required characteristics, are needed. The polarization-dependent loss variation of each optical passive component listed below shall be better than 0,2 dB (3).

44、 a) Opfical source: The optical source shall be either at fixed wavelength or wavelength-tuneable. It shall generate light at wavelength specified in the relevant detail specification, and shall emit enough optical power to allow measurements of reflectance of -50 dB to -60 dB. The suppression ratio

45、 of side modes shall be higher than 30 dB(3). An optical isolator with isolation greater than 40 dB shall be either integrated within the source package, or connected at the source output. The source shall be linearly polarized, in order to accomplish 1 Copyright Telecommunications Industry Associat

46、ion Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-61290-5-1 O IEC:2000 TIA-455-221 OPTICAL SOURCE high precision measurements of amplified spontaneous emission (ASE) power within a narrow optical bandwidth. NOTE A DFB laser o

47、r an external cavity laser can be suitable optical sources. b) Optical coupler: A 3 dB, 2 x 2 optical coupler is needed. It shall have an insertion loss lower than 3,5 dB ($) and a directivity not lower than 60 dB. Its input connectors shall have reflectance lower than -60 dB ($). Its output connect

48、or shall be of the same type as the OFA input connector. Its output unused port shall have a reflectance lower than -60 dB ($). The polarization dependent loss of the optical coupler shall be less than 0,5 dB ($). - 1 - PO LARI ZATI O N 71 3 CONTROLLER 2x2 Opfical power mefer: This device is used fo

49、r calibration purposes. It shall have a measurement accuracy better than k0,2 dB, a dependence of the state of polarization lower than 0,l dB ($), within the operational wavelength bandwidth of the OFA. Its dynamic range shall exceed the range of reflectance to be measured. Opfical specfrum analyzer: Its linearity and accuracy of spectral-power-measurement shall be better than kl,5 dB an