ANSI ISA 75.08.06-2002 Face-to-Face Dimensions for Flanged Globe-Style Control Valve Bodies (Classes 900 1500 and 2500)《带凸缘的球型(类型900、1500和2500)控制阀体的面对面尺寸》.pdf

《ANSI ISA 75.08.06-2002 Face-to-Face Dimensions for Flanged Globe-Style Control Valve Bodies (Classes 900 1500 and 2500)《带凸缘的球型(类型900、1500和2500)控制阀体的面对面尺寸》.pdf》由会员分享，可在线阅读，更多相关《ANSI ISA 75.08.06-2002 Face-to-Face Dimensions for Flanged Globe-Style Control Valve Bodies (Classes 900 1500 and 2500)《带凸缘的球型(类型900、1500和2500)控制阀体的面对面尺寸》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、 AMERICAN NATIONAL STANDARD ANSI/ISA-75.08.06-2002 (R2013) Formerly ANSI/ISA-75.16-1993 Face-to-Face Dimensions for Flanged Globe-Style Control Valve Bodies (Classes 900, 1500, and 2500) Approved 31 January 2013 ANSI/ISA-75.08.06-2002 (R2013) Face-to-Face Dimensions for Flanged Globe-Style Control V

2、alve Bodies (Classes 900, 1500, and 2500) ISBN: 978-1-937560-99-7 Copyright 2013 by ISA. All rights reserved. Not for resale. Printed in the United States of America. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means (electronic m

3、echanical, photocopying, recording, or otherwise), without the prior written permission of the Publisher. ISA 67 Alexander Drive P.O. Box 12277 Research Triangle Park, North Carolina 27709- 3 - ANSI/ISA-75.08.06-2002 (R2013) Preface This preface, as well as all footnotes and annexes, is included for

4、 information purposes and is not part of ANSI/ISA-75.08.06-2002 (R2013). The standards referenced within this document may contain provisions which, through reference in this text, constitute requirements of this document. At the time of publication, the editions indicated were valid. All standards

5、are subject to revision, and parties to agreements based on this document are encouraged to investigate the possibility of applying the most recent editions of the standards indicated within this document. Members of IEC and ISO maintain registers of currently valid International Standards. ANSI mai

6、ntain registers of currently valid U.S. National Standards. This document has been prepared as part of the service of ISA toward a goal of uniformity in the field of instrumentation. To be of real value, this document should not be static but should be subject to periodic review. Toward this end, th

7、e Society welcomes all comments and criticisms and asks that they be addressed to the Secretary, Standards and Practices Board; ISA; 67 Alexander Drive; P. O. Box 12277; Research Triangle Park, NC 27709; Telephone (919) 549-8411; Fax (919) 549-8288; E-mail: standardsisa.org. The ISA Standards and Pr

8、actices Department is aware of the growing need for attention to the metric system of units in general, and the International System of Units (SI) in particular, in the preparation of instrumentation standards. The Department is further aware of the benefits to USA users of ISA standards of incorpor

9、ating suitable references to the SI (and the metric system) in their business and professional dealings with other countries. Toward this end, this Department will endeavor to introduce SI-acceptable metric units in all new and revised standards, recommended practices, and technical reports to the g

10、reatest extent possible. IEEE/ASTM SI 10, American National Standard for Metric Practice, and future revisions, will be the reference guide for definitions, symbols, abbreviations, and conversion factors. It is the policy of ISA to encourage and welcome the participation of all concerned individuals

11、 and interests in the development of ISA standards, recommended practices, and technical reports. Participation in the ISA standards-making process by an individual in no way constitutes endorsement by the employer of that individual, of ISA, or of any of the standards, recommended practices, and te

12、chnical reports that ISA develops. CAUTION ISA DOES NOT TAKE ANY POSITION WITH RESPECT TO THE EXISTENCE OR VALIDITY OF ANY PATENT RIGHTS ASSERTED IN CONNECTION WITH THIS DOCUMENT, AND ISA DISCLAIMS LIABILITY FOR THE INFRINGEMENT OF ANY PATENT RESULTING FROM THE USE OF THIS DOCUMENT. USERS ARE ADVISE

13、D THAT DETERMINATION OF THE VALIDITY OF ANY PATENT RIGHTS, AND THE RISK OF INFRINGEMENT OF SUCH RIGHTS, IS ENTIRELY THEIR OWN RESPONSIBILITY. PURSUANT TO ISAS PATENT POLICY, ONE OR MORE PATENT HOLDERS OR PATENT APPLICANTS MAY HAVE DISCLOSED PATENTS THAT COULD BE INFRINGED BY USE OF THIS DOCUMENT AND

14、 EXECUTED A LETTER OF ASSURANCE COMMITTING TO THE GRANTING OF A LICENSE ON A WORLDWIDE, NON-DISCRIMINATORY BASIS, WITH A FAIR AND REASONABLE ROYALTY RATE AND FAIR AND REASONABLE TERMS AND CONDITIONS. FOR MORE INFORMATION ON SUCH DISCLOSURES AND LETTERS OF ASSURANCE, CONTACT ISA OR VISIT WWW.ISA.ORG/

15、STANDARDSPATENTS. OTHER PATENTS OR PATENT CLAIMS MAY EXIST FOR WHICH A DISCLOSURE OR LETTER OF ASSURANCE HAS NOT BEEN RECEIVED. ISA IS NOT RESPONSIBLE FOR IDENTIFYING PATENTS OR PATENT APPLICATIONS FOR WHICH A LICENSE MAY BE REQUIRED, FOR CONDUCTING INQUIRIES INTO THE LEGAL VALIDITY OR SCOPE OF PATE

16、NTS, OR DETERMINING WHETHER ANSI/ISA-75.08.06-2002 (R2013) - 4 - ANY LICENSING TERMS OR CONDITIONS PROVIDED IN CONNECTION WITH SUBMISSION OF A LETTER OF ASSURANCE, IF ANY, OR IN ANY LICENSING AGREEMENTS ARE REASONABLE OR NON-DISCRIMINATORY. ISA REQUESTS THAT ANYONE REVIEWING THIS DOCUMENT WHO IS AWA

17、RE OF ANY PATENTS THAT MAY IMPACT IMPLEMENTATION OF THE DOCUMENT NOTIFY THE ISA STANDARDS AND PRACTICES DEPARTMENT OF THE PATENT AND ITS OWNER. ADDITIONALLY, THE USE OF THIS DOCUMENT MAY INVOLVE HAZARDOUS MATERIALS, OPERATIONS OR EQUIPMENT. THE DOCUMENT CANNOT ANTICIPATE ALL POSSIBLE APPLICATIONS OR

18、 ADDRESS ALL POSSIBLE SAFETY ISSUES ASSOCIATED WITH USE IN HAZARDOUS CONDITIONS. THE USER OF THIS DOCUMENT MUST EXERCISE SOUND PROFESSIONAL JUDGMENT CONCERNING ITS USE AND APPLICABILITY UNDER THE USERS PARTICULAR CIRCUMSTANCES. THE USER MUST ALSO CONSIDER THE APPLICABILITY OF ANY GOVERNMENTAL REGULA

19、TORY LIMITATIONS AND ESTABLISHED SAFETY AND HEALTH PRACTICES BEFORE IMPLEMENTING THIS DOCUMENT. THE USER OF THIS DOCUMENT SHOULD BE AWARE THAT THIS DOCUMENT MAY BE IMPACTED BY ELECTRONIC SECURITY ISSUES. THE COMMITTEE HAS NOT YET ADDRESSED THE POTENTIAL ISSUES IN THIS VERSION. The following people s

20、erved as members of ISA Committee SP75.08 and approved ANSI/ISA-75.08.06-2002: NAME COMPANY W. Weidman, Chairman Parsons Energy & Chemicals Group H. Baumann HB Services Partners LLC G. Borden Consultant R. Brodin Emerson Process Management F. Cain Flowserve Corporation R. Chown OTEC Process Systems

21、Inc. B. Hatton Dezurik J. Reed Norriseal H. Sonderegger Anvil International Inc. The following people served as members of ISA Committee SP75 and approved ANSI/ISA-75.08.06-2002: NAME COMPANY D. Buchanan, Chairman Consultant W. Weidman, Managing Director Parsons Energy & Chemicals Group K. Schoonove

22、r, Secretary Con-Tek Valves Inc. A. Abromaitis Red Valve Co Inc. H. Backinger Consultant G. Barb Consultant H. Baumann HB Services Partners LLC J. Beall* Emerson Process Management W. Black Curtiss-Wright Flow Control Corporation G. Blackwell Industrial Valve H. Boger* Masoneilan Dresser G. Borden C

23、onsultant S. Boyle Metso Automation USA Inc. R. Brodin* Emerson Process Management - 5 - ANSI/ISA-75.08.06-2002 (R2013) F. Cain Flowserve Corporation A. Engels Praxair Inc. H. Fuller Valvcon Corporation J. George Richards Industries L. Griffith Consultant J. Jamison Bantrel Inc. R. Jeanes TXU Electr

24、ic J. Kersh M W Kellogg Company C. Langford Cullen G. Langford Inc. W. Lestan* Masoneilan Dresser A. Libke* SPX Valves & Controls DeZurik Products R. Louviere Services Unlimited J. McCaskill Power Chokes A. McCauley Chagrin Valley Controls Inc. R. McEver* Emerson Valve Automation H. Miller Control C

25、omponents Inc. T. Molloy CMES Inc. L. Ormanoski Frick Company J. Ozol Northern States Power W. Rahmeyer Utah State University J. Reed Norriseal A. Shea* SPX Valves & Controls DeZurik Products E. Skovgaard Leslie Controls Inc. H. Sonderegger Anvil International Inc. _ * One vote per company. ANSI/ISA

26、-75.08.06-2002 was approved for publication by the ISA Standards and Practices Board on 26 September 2002. NAME COMPANY M. Zielinski Emerson Process Management D. Bishop David N Bishop, Consultant D. Bouchard Paprican M. Cohen Consultant M. Coppler Ametek, Inc. B. Dumortier Schneider Electric W. Hol

27、land Southern Company E. Icayan ACES Inc A. Iverson Ivy Optiks R. Jones Dow Chemical Company V. Maggioli Feltronics Corporation T. McAvinew I&C Engineering, LLC A. McCauley, Jr. Chagrin Valley Controls, Inc. G. McFarland Westinghouse Process Control Inc. R. Reimer Rockwell Automation J. Rennie Facto

28、ry Mutual Research Corporation H. Sasajima Yamatake Corporation I. Verhappen Syncrude Canada Ltd. R. Webb POWER Engineers W. Weidman Parsons Energy & Chemicals Group J. Weiss KEMA Consulting M. Widmeyer Stanford Linear Accelerator Center R. Wiegle CANUS Corporation C. Williams Eastman Kodak Company

29、G. Wood Graeme Wood Consulting ANSI/ISA-75.08.06-2002 (R2013) - 6 - The following people served as members of ISA Subcommittee ISA75.08 and reaffirmed ANSI/ISA-75.08.06-2002 (R2013): NAME COMPANY W. Weidman, Chair WCW Consulting H. Baumann H B Services Partners LLC G. Borden Consultant F. Cain Flows

30、erve Corporation R. Chown Madawaska Mechanical Inc. R. Duimstra Fisher Controls International Inc. V. Mezzano Fluor Corporation J. Reed Consultant J. Young The Dow Chemical Company The following people served as members of ISA Committee ISA75 and reaffirmed ANSI/ISA-75.08.06-2002 (R2013): NAME COMPA

31、NY J. Young, Chair The Dow Chemical Company W. Weidman, Managing Director WCW Consulting L. Al-Awami Saudi Aramco H. Baumann H B Services Partners LLC J. Beall Emerson Process Management M. Bober Copes-Vulcan H. Boger GE Oil & Gas G. Borden Consultant S. Boyle Metso Automation USA Inc. J. Broyles En

32、bridge Pipelines Inc. F. Cain Flowserve Corporation W. Cohen KBR R. Duimstra Fisher Controls International Inc. J. Faramarzi Control Components Inc. J. George Richards Industries C. Hergert Kellogg Brown & Root H. Hoffmann Consultant J. Jamison Spectra Energy Ltd. J. Kiesbauer Samson Aktiengesellsch

33、aft C. Langford Cullen G Langford Inc. A. Libke DeZurik G. Liu Consultant T. Loudin Flowrox Inc. H. Maxwell Bechtel Power Corp. J. McCaskill Expro Group A. McCauley Chagrin Valley Controls Inc. R. McEver Consultant V. Mezzano Fluor Corporation H. Miller Consultant T. Molloy CMES Inc. L. Ormanoski Co

34、nsultant J. Reed Consultant E. Skovgaard Control Valve Solutions - 7 - ANSI/ISA-75.08.06-2002 (R2013) This standard was approved for reaffirmation by the ISA Standards and Practices Board on 14 January 2013: NAME COMPANY D. Dunn, Vice President Aramco Services Co. R. Bartusiak ExxonMobil Chemical Co

35、mpany P. Brett Honeywell Inc. J. Campbell Consultant M. Coppler Det Norske Veritas Certification Inc. E. Cosman The Dow Chemical Co. B. Dumortier Schneider Electric J. Federlein Federlein & Assoc. Inc. J. Gilsinn Kenexis Consulting E. Icayan ACES Inc. J. Jamison Spectra Energy Ltd. K. Lindner Endres

36、s+Hauser Process Solutions AG V. Maggioli Feltronics Corp. T. McAvinew Instrumentation and Control Engineering LLC R. Reimer Rockwell Automation S. Russell Valero Energy Corp. N. Sands DuPont H. Sasajima Azbil Corp. T. Schnaare Rosemount Inc. J. Tatera Tatera & Associates Inc. I. Verhappen Industria

37、l Automation Networks Inc. W. Weidman WCW Consulting J. Weiss Applied Control Solutions LLC M. Wilkins Yokogawa IA Global Marketing (USMK) D. Zetterberg Chevron Energy Technology Company This page intentionally left blank. - 9 - ANSI/ISA-75.08.06-2002 (R2013) Contents 1 Scope . 11 2 Purpose 11 3 Def

38、initions 11 4 Dimensional data . 11 5 References . 13 Annex A Dimensions for metrically sized valves 15 This page intentionally left blank. - 11 - ANSI/ISA-75.08.06-2002 (R2013) 1 Scope This standard applies to flanged globe-style control valves, sizes 15 mm (1/2 inch) through 450 mm (18 inches), ha

39、ving top, top and bottom, port, or cage guiding. 2 Purpose 2.1 The purpose of this standard is to aid users in their piping design by providing Classes 900, 1500, and 2500, flanged globe-style control valve dimensions, without giving special consideration to the equipment manufacturer to be used. 2.

40、2 The short-long dimensions provided in Table 1 clarify 2.1 by consolidating the diversity of existing manufacturers lengths into two sets of dimensions for each valve size. Before using either the short or long dimension, the piping designer should confirm with the selected valve manufacturer which

41、 dimension is correct for the valve(s) being supplied. 3 Definitions For definitions of terms used in this standard, see ANSI/ISA-75.05.01-2000 (R2005), Control Valve Terminology. 4 Dimensional data 4.1 For face-to-face dimensions for flanged globe-style control valves, see Table 1. 4.2 For end-to-e

42、nd dimensions of flanged with ring joint ends, Dimension “A“ shall be adjusted according to ASME B16.10-2000 (R2003), paragraph 3.3. ANSI/ISA-75.08.06-2002 (R2013) - 12 - Table 1 Face-to-face dimensions for flanged globe-style control valves Nominal Valve Size PN 150 (Class 900) PN 250 (Class 1500)

43、PN 420 (Class 2500) Tolerance Dimension “A“ Dimension “A“ Dimension “A“ mm inches mm inches mm inches mm inches Short Long Short Long Short Long Short Long Short Long Short Long mm inches 15 1/2 273 292 10.75 11.50 273 292 10.75 11.50 308 318 12.12 12.50 1.6 0.062 20 3/4 273 292 10.75 11.50 273 292

44、10.75 11.50 308 318 12.12 12.50 1.6 0.062 25 1 273 292 10.75 11.50 273 292 10.75 11.50 308 318 12.12 12.50 1.6 0.062 40 1-1/2 311 333 12.25 13.12 311 333 12.25 13.12 359 381 14.12 15.00 1.6 0.062 50 2 340 375 13.38 14.75 340 375 13.38 14.75 400 16.25 1.6 0.062 65 2-1/2 410 16.12 410 16.12 441 17.38

45、1.6 0.062 80 3 387 441 15.25 17.38 406 460 16.00 18.12 498 660 19.62 26.00 1.6 0.062 100 4 464 511 18.25 20.12 483 530 19.00 20.87 575 737 22.62 29.00 1.6 0.062 150 6 600 714 21.87 28.12 692 768 24.00 30.25 819 864 32.25 34.00 1.6 0.062 200 8 781 914 30.75 36.00 838 972 33.00 38.25 1022 40.25 1.6 0.

46、062 250 10 864 991 34.00 39.00 991 1067 39.00 42.00 1270 1372 50.00 54.00 1.6 0.062 300 12 1016 1130 40.00 44.50 1130 1219 44.50 48.00 1321 1575 52.00 62.00 3.2 0.125 350 14 1257 49.50 1257 49.50 3.2 0.125 400 16 1422 56.00 1422 56.00 3.2 0.125 450 18 1727 68.00 1727 68.00 3.2 0.125 - 13 - ANSI/ISA-

47、75.08.06-2002 (R2013) 5 References The following references are included for the definition of pressure classes, flange dimensions, material identification, and cross-reference information. AMERICAN SOCIETY OF MECHANICAL ENGINEERS (ASME) ASME B16.5-2003 Pipe Flanges and Flanged Fittings: NPS 1/2 thr

48、ough 24 ASME B16.10-2000 (R2003) Face-to-Face and End-to-End Dimensions of Valves ASME B16.34-2004 Valves Flanged, Threaded, and Welding End Available from: ASME Three Park Avenue New York, NY 10016-5990 Tel: 800-843-2763 http:/www.asme.org This page intentionally left blank. 15 ANSI/ISA-75.08.06-20

49、02 (R2013) Annex A Dimensions for metrically sized valves This annex is not part of ANSI/ISA-75.08.06-2002 (R2013), but is included to facilitate its use. The ANSI standards listed in the bibliography contain valve body design information in addition to face-to-face dimensions. Dimensions for metrically sized valves are nominal conversions that are conventionally used in the Manufacturers Standardization Society (MSS) of the Valve and Fitting Industrys Publication MSS-SP-86-2002, and in International Standards Organization (ISO) an