ANSI INCITS ISO IEC 7811-3-1995 Identification Cards - Recording Technique - Part 3 Location of Embossed Characters on ID-1 Cards (Adopted by INCITS).pdf

《ANSI INCITS ISO IEC 7811-3-1995 Identification Cards - Recording Technique - Part 3 Location of Embossed Characters on ID-1 Cards (Adopted by INCITS).pdf》由会员分享，可在线阅读，更多相关《ANSI INCITS ISO IEC 7811-3-1995 Identification Cards - Recording Technique - Part 3 Location of Embossed Characters on ID-1 Cards (Adopted by INCITS).pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、 INCITS/ISO/IEC 7811-3-1995(formerly ANSI/ISO/IEC 7811-3-1995)for Identification Cards -Recording Technique -Part 3: Location of Embossed Characterson ID-1 CardsANSI/ISO/IEC 7811-3-l 995 Revision and redesignation of ANSI/IS0 781 l-3=1985(R1988) American National Standard for Identification Cards -

2、Recording Technique - Part 3: Location of Embossed Characters on ID-1 Cards Secretariat Information Technology Industry Council Approved August 17, 1995 American National Standards Institute, Inc. AmericanNationalStandardApproval of an American National Standard requires review by ANSI that therequi

3、rements for due process, consensus, and other criteria for approval havebeen met by the standards developer.Consensus is established when, in the judgment of the ANSI Board of StandardsReview, substantial agreement has been reached by directly and materiallyaffected interests. Substantial agreement

4、means much more than a simplemajority, but not necessarily unanimity. Consensus requires that all views andobjections be considered, and that a concerted effort be made toward theirresolution.The use of American National Standards is completely voluntary; their existencedoes not in any respect precl

5、ude anyone, whether he has approved the standardsor not, from manufacturing, marketing, purchasing, or using products, processes,or procedures not conforming to the standards.The American National Standards Institute does not develop standards and will inno circumstances give an interpretation of an

6、y American National Standard.Moreover, no person shall have the right or authority to issue an interpretation ofan American National Standard in the name of the American National StandardsInstitute. Requests for interpretations should be addressed to the secretariat orsponsor whose name appears on t

7、he title page of this standard.CAUTION NOTICE: This American National Standard may be revised orwithdrawn at any time. The procedures of the American National StandardsInstitute require that action be taken periodically to reaffirm, revise, or withdrawthis standard. Purchasers of American National S

8、tandards may receive currentinformation on all standards by calling or writing the American National StandardsInstitute.Published byAmerican National Standards Institute11 West 42nd Street, New York, New York 10036Copyright 1996 by Information Technology Industry Council (ITI)All rights reserved.The

9、se materials are subject to copyright claims of International Standardization Organization (ISO),International Electrotechnical Commission (IEC), American National Standards Institute (ANSI), andInformation Technology Industry Council (ITI). Not for resale. No part of this publication may bereproduc

10、ed in any form, including an electronic retrieval system, without the prior written permission of ITI.All requests pertaining to this standard should be submitted to ITI, 1250 Eye Street NW, Washington, DC20005.Printed in the United States of AmericaContents Page Foreword . . . . . . . . . . . . . .

11、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12、 . . . . . . . . . . . . . . . . . . . . . . . . . . . iv 1 Scope 1 2 Conformance . 1 3 Normative references . . . . . . . . . . . . . . . . . . . . . . . *. 1 4 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13、. . . . . . . . . . . . . . . . . . . . . . . . . . 1 5 Assigned areas 1 6 Identification number line . 2 7 Name and address area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Figure 1 Embossing locations .

14、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . * 3 Foreword (This foreword is not part of American National Standard ANSI/ISO/IEC 7811-3-1995. This document is identical to ISO/IEC 7811-3-I 995 and the following five paragraphs are the or

15、iginal foreword as it appeared in that document.) IS0 (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of IS0 or IEC participate in the development

16、of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. IS0 and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in

17、 liaison with IS0 and IEC, also take part in the work. In the field of information technology, IS0 and IEC have established a joint technical committee, ISO/IEC JTC 1. Draft International Standards adopt- ed by the joint technical committee are circulated to the member bodies for voting. Publication

18、 as an International Standard requires approval by at least 75% of the national bodies casting a vote. International Standard ISO/IEC 781 l-3 was prepared by Joint Technical Committee ISO/IEC JTC 1, information technology, Subcommittee SC 17, Identification cards and related devices. This second edi

19、tion cancels and replaces the first edition (IS0 7811-3: 1985), of which it constitutes a technical revision. ISO/IEC 7811 consists of the following parts, under the general title /den tifica tion cards - Recording technique: - Part I: Embossing - Part 2: Magnetic stripe - Part 3: Location of emboss

20、ed characters on ID-I cards - Part 4: Location of read-only magnetic tracks - Tracks I and 2 - Part 5: Location of read-write magnetic tracks - Tracks 2 Requests for interpretation, suggestions for improvement or addenda, or defect reports are welcome. They should be sent to the X3 Secretariat, Info

21、rmation Technology Industry Council, 1250 Eye Street, NW, Suite 200, Washington, DC 20005. This standard was processed and approved for submittal to ANSI by Accredited Standards Committee on Information Technology, X3. Committee approval of the standard does not necessarily imply that all committee

22、members voted for its approval. At the time it approved this standard, the X3 Committee had the following members: James D. Converse, Chair Donald C. Loughry, Vice-Chair Joanne Flanagan, Secretary Organization Represented Name of Representative American Nuclear Society . . . . . . . . . . . . . . .

23、. . . . . . . . . . . . . . . . . . . . . . . . . . * Geraldine C. Main Sally Hartzell (Alt.) AMP, Inc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Edward Kelly Charles Brill (Alt.) Apple Computer, Inc . . . . . . . . . . . . . . . . . . . . . . . .

24、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . David K. Michael ii Organization Represented Name of Representative AT - make allowances for an identification number with maximum length; - for financial applications if a character position is avail- able, a blank space is recomm

25、ended to be inserted between the issuer identification and the individual account identifier of the identification number (refer to ISO/IEC 7812). If these provisions are not taken into account, it may be necessary to agree on certain limitations before the inter- change of cards and data among diff

26、erent systems can effectively take place. The location follows: specifications (see figure 1) shall be as a) b) cl distance, A, between the centreline of the identification number line and the bottom edge of the card: 21,42 mm f. 0,12 mm (0,843 in f 0,005 in) distance, B, between the centreline of t

27、he first character position and the left edge of the card: lo,18 mm * 0,25 mm (0,401 in f 0,010 in) distance, C, between the centreline of the first character position and the 19th character position shall not exceed: 65,31 mm * 0,76 mm (2,571 in f 0,030 in) d) maximum distance, H, from the bottom e

28、dge of the card to the top of Area 1 shall be: 24,03 mm (0,946 in) 7 Name and address area The name and address area provides space for four lines of 27 characters each at a nominal spacing of 10 characters per 25,4 mm (IO characters per inch) of the type specified in lSO/IEC 781 l-l. Any informatio

29、n embossed in the name and address area should always be embossed as far as possible from the identification number (see figure I). WARNING - Those card issuers who require embossment of four name and address lines should be aware that the imprinted documents produced from their cards may not be acc

30、eptable in an interchange environment due to OCR clear area requirements on some types of OCR reading equipment. The location specifications (see figure follows: I) shall be as a) maximum height, D, of the name and address area: 14,53 mm (0,572 in) NOTE - The measurement is referenced surface and do

31、es not include tolerances. to the printing b) bottom margin, E, between name and address area and the edge of the card: 2,41 mm min. (0,095 in min.) 3,30 mm max. (0,130 in max.) NOTE - When used in conjunction with a magnetic stripe, the minimum margin should be 2,54 mm (0,100 in); see ISO/IEC 7810.

32、 cl the distance, F, between the centreline of the first character position of each line and the left edge of the card: 7,65 mm f 0,25 mm (0,301 in f 0,010 in) NOTE - The first character in the name and address area need not be justified to the left. However, the use of 27 character positions is bas

33、ed on 7,65 mm (0,301 in) distance to the edge of the card as stated above. d) distance, G, between the centreline of the first character position and the 27th character position shall not exceed: 66,04 mm f 0,76 mm (2,600 in f: 0,030 in) 2 l- a 2- /: Lu . ! -moooooooooooooo- I 0000000000000000000000000 _oooocKlooooo.oooooooocloooo 0000000000000000000000000 00000000000000000000000000 I I - ANSI/ISO/IEC 7811-3-I 995 Figure 1 - Embossing locations 3