ANSI INCITS ISO IEC 7811-1-2002 Identification cards Recording technique Part 1 Embossing.pdf

《ANSI INCITS ISO IEC 7811-1-2002 Identification cards Recording technique Part 1 Embossing.pdf》由会员分享，可在线阅读，更多相关《ANSI INCITS ISO IEC 7811-1-2002 Identification cards Recording technique Part 1 Embossing.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference numberISO/IEC 7811-1:2002(E)ISO/IEC 2002INTERNATIONAL STANDARD ISO/IEC7811-1Third edition2002-09-15Identification cards Recording technique Part 1: Embossing Cartes didentification Technique denregistrement Partie 1: Estampage Adopted by INCITS (InterNational Committee for Information Tec

2、hnology Standards) as an American National Standard.Date of ANSI Approval: 2/13/2003Published by American National Standards Institute,25 West 43rd Street, New York, New York 10036Copyright 2003 by Information Technology Industry Council (ITI).All rights reserved.These materials are subject to copyr

3、ight claims of International Standardization Organization (ISO), InternationalElectrotechnical Commission (IEC), American National Standards Institute (ANSI), and Information Technology Industry Council(ITI). Not for resale. No part of this publication may be reproduced in any form, including an ele

4、ctronic retrieval system, withoutthe prior written permission of ITI. All requests pertaining to this standard should be submitted to ITI, 1250 Eye Street NW,Washington, DC 20005.Printed in the United States of AmericaISO/IEC 7811-1:2002(E) PDF disclaimer This PDF file may contain embedded typefaces

5、. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing

6、 Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized

7、 for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO/IEC 2002 All rights reserved. Unless otherwise specified, no

8、part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postal

9、e 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO/IEC 2002 All rights reservedISO/IEC 7811-1:2002(E) ISO/IEC 2002 All rights reserved iiiContents Page Foreword.iv 1 Scope 1 2 Conformance1 3 Normative references1 4

10、Terms and definitions .2 5 Card characteristics 2 5.1 Card warpage .2 5.2 Surface distortions 2 5.3 Card width and height.3 6 Visually and machine readable characters.3 6.1 Character set and type font 3 6.2 Character spacing .4 6.3 Character height 4 6.4 Relief height of embossed characters.4 7 Visu

11、ally readable characters 4 7.1 Character set and type font 4 7.2 Character spacing .4 7.3 Relief height of embossed characters.4 8 Assigned embossing areas 4 8.1 Identification number line.5 8.2 Name and address area 6 Annex A (normative) Pictorial representation of numeric data7 Annex B (normative)

12、 Farrington 7B Print specifications8 Annex C (informative) Embossability20 ISO/IEC 7811-1:2002(E) iv ISO/IEC 2002 All rights reserved Foreword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide st

13、andardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields

14、 of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in

15、accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an Internationa

16、l Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO/IEC 7811 may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent righ

17、ts. ISO/IEC 7811-1 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 17, Cards and personal identification. This third edition of ISO/IEC 7811-1 cancels and replaces ISO/IEC 7811-1:1995 and ISO/IEC 7811-3:1995. The user is encouraged to review the entir

18、e standard for revisions and updates. The major changes made during this revision are listed below. 1. The requirements given in ISO/IEC 7811-3:1995 are included in this edition of ISO/IEC 7811-1. 2. Special physical characteristics for embossing formerly detailed in ISO/IEC 7810:1995 have been move

19、d to this standard. 3. Added an informative annex for a test method for embossability. ISO/IEC 7811 consists of the following parts, under the general title Identification cards Recording technique: Part 1: Embossing Part 2: Magnetic stripe Low coercivity Part 6: Magnetic stripe High coercivity Anne

20、xes A and B form a normative part of this part of ISO/IEC 7811. Annex C is information only. 11 ScopeThis part of ISO/IEC 7811 is one of a series of standards describing the parameters for identification cards asdefined in the definitions clause and the use of such cards for international interchang

21、e.This part of ISO/IEC 7811 specifies requirements for embossed characters on identification cards. The embossedcharacters are intended for transfer of data either by use of imprinters or by visual or machine reading. It takes intoconsideration both human and machine aspects and states minimum requi

22、rements.It is the purpose of this series of standards to provide criteria to which cards shall perform. No consideration isgiven within these standards to the amount of use, if any, experienced by the card prior to test. Failure to conformto specified criteria should be negotiated between the involv

23、ed parties.ISO/IEC 10373-1 specifies the test procedures used to check cards against the parameters specified in thispart of ISO/IEC 7811.NOTE Numeric values in the SI and/or Imperial measurement system in this part of ISO/IEC 7811 may have beenrounded off and therefore are consistent with, but not

24、exactly equal to, each other. Either system may be used, but the twoshould not be intermixed or reconverted. The original design was made using the Imperial measurement system.2 ConformanceA prerequisite for conformance with this part of ISO/IEC 7811 is conformance with ISO/IEC 7810 for the ID-1 siz

25、ecard. An identification card is in conformance with this part of ISO/IEC 7811 if it meets all mandatory requirementsspecified herein. Default values apply if no others are specified.3 Normative referencesThe following normative documents contain provisions which, through reference in this text, con

26、stitute provisions ofthis part of ISO/IEC 7811. For dated references, subsequent amendments to, or revisions of, any of thesepublications do not apply. However, parties to agreements based on this part of ISO/IEC 7811 are encouraged toinvestigate the possibility of applying the most recent editions

27、of the normative documents indicated below. Forundated references, the latest edition of the normative document referred to applies. Members of ISO and IECmaintain registers of currently valid International StandardsISO 1073-1, Alphanumeric character sets for optical recognition Part 1: Character se

28、t OCR-A Shapes anddimensions of the printed imageISO 1073-2, Alphanumeric character sets for optical recognition Part 2: Character set OCR-B Shapes anddimensions of the printed imageISO 1831, Printing specifications for optical character recognitionISO/IEC 7810, Identification cards Physical charact

29、eristicsISO/IEC 7812-1, Identification cards Identification of issuers Part 1: Numbering systemINTERNATIONAL STANDARD ISO/IEC 7811-1:2002(E)Identification cards Recording technique Part 1: Embossing ISO/IEC 2002 All rights reserved 2ISO/IEC 7812-2, Identification cards Identification of issuers Part

30、 2: Application and registration proceduresISO/IEC 10373-1, Identification cards Test methods Part 1: General characteristics tests4 Terms and definitionsFor the purposes of this part of ISO/IEC 7811, the definition of “identification card” given in ISO/IEC 7810 and thefollowing terms and definition

31、s apply.4.1embossingto raise characters in relief from the front surface of the card4.2unused cardcard which has been embossed with all the characters required for its intended purpose but has not been issued4.3returned cardembossed card after it has been issued to the card holder and returned for t

32、he purpose of testing4.4identification numbernumber that identifies the card holder5 Card characteristicsSpecial attention shall be paid to the characteristics of the material affecting its suitability for this purpose,particularly in respect to its ability to resist crushing and collapsing of the e

33、mbossed parts when operating inimprinters.Cards shall be made of PVC (polyvinyl chloride) and/or PVCA (polyvinyl chloride acetate) or materials having equalor better performance such as polyesters, polyethylenes and polycarbonates.NOTE Refer to machine manufacturer instructions regarding card constr

34、uction requirements for achieving embossedcharacter relief heights in compliance with this part of ISO/IEC 7811. At the time of publication there was no agreed testmethod for verifying the suitability of card structures for embossing. See Informative Annex C.5.1 Card warpageWhen lying convex side up

35、 on a flat rigid surface, the maximum distance from the flat surface to any non-embossedportion of the convex side of an embossed card immediately prior to issue shall not be greater than 2,5 mm(0.10 in) including the card thickness.NOTE The amount of card warpage depends on the card material and th

36、e embossing technique used.5.2 Surface distortionsNo raised area shall exceed 0,51 mm (0.020 in) on the front of the card in the area A as shown in Figure 1.ISO/IEC 7811-1:2002(E) ISO/IEC 2002 All rights reserved 3widthheight2,54(0.100)dimensions in millimetres (inches)24,03(0.946)AreaAfront of card

37、top reference edgeWidth Heightmaximum minimum maximum minimum85,90 (3.382) 85,47 (3.365) 54,18 (2.133) 53,92 (2.123)Figure 1 Embossed card dimensions5.3 Card width and heightAll points on the edges of the embossed card in the finished state, except for the rounded corners, shall fallbetween two conc

38、entric, similarly aligned rectangles as defined in Figure 1 for maximum height and width, andminimum height and width.NOTE 1 Card width and height tolerances given here are different than those in ISO/IEC 7810 to account for changes in cardsize due to embossing.NOTE 2 All identification card standar

39、ds use the top edge of the card as the reference edge for dimensions, except for thisembossing standard which, for historical reasons, uses the bottom edge of the card as the reference.6 Visually and machine readable characters6.1 Character set and type fontThe numeric characters of one of the follo

40、wing type fonts shall be used for embossed characters intended for visualand/or machine reading, either directly from the card or from card imprints (see annex A): ISO 1073-1, OCR-A, Sizes I and IV; ISO 1073-2, OCR-B, Sizes I and IV; Type font Farrington 7B as described in Annex B.NOTE To ensure sys

41、tem compatibility in the choice of font, the attention of intending users is drawn to the necessity ofagreement with their potential interchange partners. ISO/IEC 2002 All rights reserved ISO/IEC 7811-1:2002(E) 4Print specifications are given in ISO 1831.6.2 Character spacingThe centreline to centre

42、line character spacing shall be 3,63 mm 0,15 mm (0.143 in 0.006 in).6.3 Character heightMaximum height at the printing surface of the embossed characters, encompassing centreline skew and charactermisalignment shall be 4,32 mm (0.170 in).6.4 Relief height of embossed charactersRelief height of impri

43、nting character surfaces above the card surface as measured from the non-embossed surfaceof the card to the highest point on the embossed character is shown in Table 1 for unused cards and for returnedcards.7 Visually readable characters7.1 Character set and type fontA type font such as the alphanum

44、eric, upper case characters described in ISO 1073-2, OCR-B, Size I, shouldbe used for embossed characters intended for visually reading directly from the card or from card imprints.7.2 Character spacingThe centreline to centreline character spacing shall be 2,54 mm 0,15 mm (0.100 in 0.006 in).7.3 Re

45、lief height of embossed charactersRelief height of imprinting character surfaces above the card surface as measured from the non-embossed surfaceof the card to the highest point on the embossed character is shown in Table 1 for unused cards and for returnedcards.Table 1 Relief height of embossed cha

46、ractersDimensions in millimetres (inches)Visually and machine readable characters Visually readable charactersmaximum minimum maximum minimumUnused card 0,48 0,40 0,46 0,36(0.019) (0.016) (0.018) (0.014)Returned cards 0,48 0,30 0,46 0,26(0.019) (0.012) (0.018) (0.010)NOTE Values in the table show on

47、ly the limits within which cards will function normally, and do not imply anyguarantee of relief height during the valid term for issued cards.8 Assigned embossing areasTwo areas for embossing shall be assigned to the card as shown in Figure 2.Area 1 Area reserved for the identification number line

48、according to ISO/IEC 7812. The characters inISO/IEC 7811-1:2002(E) ISO/IEC 2002 All rights reserved 5this area and imprints of the area are intended both for visual and machine reading;Area 2 Area provided for the card holders identification data such as name, address, and other datawhich may be req

49、uired. It is called “name and address area”. Data contained in this area of thecard or imprinted from the card is only intended for visual reading.adefhcbgcentreline ofcharacter 1centreline ofcharacter 19centreline ofcharacter 27centreline ofcharacter 1Identification number line (Area 1)Name and address area (Area 2)dimensions in millimetres (inches)Top reference edgeFront of cardIdentification number line (Area 1) Name and address area (Area 2)a 21,42 0,12 (0.843 0.005) e 14,53 (0.572) max