ANSI INCITS ISO 8630-1-1987 Information processing - Data interchange on 130 mm (5.25 in) flexible disk cartridges using modified frequency modulation recording at 13 262 ftprad on.pdf

《ANSI INCITS ISO 8630-1-1987 Information processing - Data interchange on 130 mm (5.25 in) flexible disk cartridges using modified frequency modulation recording at 13 262 ftprad on.pdf》由会员分享，可在线阅读，更多相关《ANSI INCITS ISO 8630-1-1987 Information processing - Data interchange on 130 mm (5.25 in) flexible disk cartridges using modified frequency modulation recording at 13 262 ftprad on.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、 INCITS/ISO 8630-1:19872010 (ISO 8630-1:1987, IDT) Information processing - Data interchange on 130 mm (5.25 in) flexible disk cartridges using modified frequency modulation recording at 13 262 ftprad, on 80 tracks on each side - Part 1 : Dimensional, physical and magnetic characteristics Reaffirmed

2、 as INCITS/ISO 8630-1:1987 R2015INCITS/ISO 8630-1:19872010 PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the

3、computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to

4、create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform

5、 the Central Secretariat at the address given below. Adopted by INCITS (InterNational Committee for Information Technology Standards) as an American National Standard. Date of ANSI Approval: 10/6/2010 Published by American National Standards Institute, 25 West 43rd Street, New York, New York 10036 C

6、opyright 2010 by Information Technology Industry Council (ITI). All rights reserved. These materials are subject to copyright claims of International Standardization Organization (ISO), International Electrotechnical Commission (IEC), American National Standards Institute (ANSI), and Information Tec

7、hnology Industry Council (ITI). Not for resale. No part of this publication may be reproduced in any form, including an electronic retrieval system, without the prior written permission of ITI. All requests pertaining to this standard should be submitted to ITI, 1101 K Street NW, Suite 610, Washingt

8、on DC 20005. Printed in the United States of America ii ITIC 2010 All rights reserved ISO 8630-l : 1987 E) Contents 0 Introduction . 1 Scope and field of application 2 Conformance 3 References 4 Definitions 4.1 flexibledisk 4.2 reference flexible disk cartridge . 4.3 Secondary Amplitude Reference Di

9、sk Cartridge . 4.4 Signal Amplitude Reference Disk Cartridge. 4.5 TypicalField . 4.6 ReferenceField 4.7 Test Recording Current 4.6 Standard Reference Amplitude . 4.9 Average Signal Amplitude . 4.10 in-contact . 4.11 formatting . 4.12 initialization. . 4.13 recordingarea . 5 General description. 5.1

10、Generalfigures 5.2 Mainelements 5.3 Description . 5.4 Optionalfeatures 6 General requirements . 6.1 Environment and transportation . 6.2 Materials . 6.3 Direction of rotation . 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 3 iii IS0 8630-l : 1987 (E) 7 Dimensional characteristics 3 7.1 Jacket

11、. 4 7.2 Liner 5 7.3 Disk . 5 6 Physical characteristics . 5 6.1 Flammability . 5 6.2 Coefficient of linear thermal expansion of the disk . 5 6.3 Coefficient of linear hygroscopic expansion of the disk . 5 6.4 Opacity . 5 8.5 Torque 5 9 Magneticcharacteristics 6 9.1 Trackgeometry . 6 9.2 Functional t

12、esting . 6 Annexes A Measurement of the cartridge thickness. 12 B Measurement of light transmittance 14 C Method for measuring the effective track width 16 INTERNATIONAL STANDARD IS0 8630-l : 1987 (E) Information processing - Data interchange on 4130 mm (5.25 in) flexible disk cartridges using modif

13、ied frequency modulation recording at 13 262 ftprad, on 80 tracks on each side - Part 1: Dimensional, physical and magnetic characteristics 0 Introduction IS0 8630 specifies the characteristics of 130 mm (5.25 in) flexible disk cartridges recorded at 13 292 ftprad, using modified frequency modulatio

14、n (MFM) recording, on 80 tracks on each side. IS0 8630-2 and IS0 9630-3 each specify the quality of recorded signals, the track layout, and a track format to be used on 130 mm (5.25 in), 13 292 ftprad flexible disk cartridges intended for data interchange between data processing systems. IS0 9630-l

15、and IS0 9630-2, together with the labelling scheme specified in IS0 7665, provide for full data interchange between data processing systems. IS0 8630-I and IS0 8630-3, together with the labelling scheme specified in IS0 9293, provide an alternative method of full data interchange between data proces

16、sing systems. 1 Scope and field of application This part of IS0 8630 specifies the dimensional, physical and magnetic characteristics of the cartridge so as to provide physical interchangeability between data processing systems. NOTE - Numeric values in the SI and/or Imperial measurement system in t

17、his part of IS0 8630 may have been rounded off and therefore are consistent with, but not exactly equal to, each other. Either system may be used, but the two should be neither intermixed nor re-converted. The original design was made using Imperial units and further developments were made using SI

18、units. 2 Conformance A flexible disk cartridge shall be in conformance with IS0 9630 when it meets all the requirements of this part of IS0 8630 and all those of either IS0 8630-2 or IS0 8630-3. 3 References IS0 646, Information processing - IS0 7-bit coded character set for information interchange.

19、 IS0 2022, Information processing - IS0 Fbit and B-bit coded character sets - Code extension techniques. IS0 4973, Information processing - IS0 8-bit code for infor- mation interchange - Structure and rules for implementation. IS0 9429, Information processing - IS0 7-b - the liner; - the jacket. The

20、 cartridge is stored in an envelope. 5.3 Description The jacket is of a square form. It includes a central window, an index window, and a head window in both sides. The liner is fixed to the inside of the jacket. It comprises two layers of material between which the disk is held. The liner has the s

21、ame openings as the jacket. The disk has only a central hole and an index hole. 5.4 Optional features The interchange characteristics of the jacket allow for varia- tions of its construction as follows: 6 a) the jacket may include flaps (for example three flaps as shown in figure 2, or none); and b)

22、 notches along the reference edge. General requirements 6.1 Environment and transportation 6.1.1 Testing environment Tests and measurements made on the cartridge to check the requirements of IS0 6630 shall be carried out under the follow- ing conditions: - temperature: 23 f 2 OC (73 f 4 OFI; - relat

23、ive humidity: 40 to 60 % ; - conditioning before testing: 24 h minimum. 1) NBS, Office of Standard Reference Materials, Room 311, Chemistry Building, Gaithersburg, MD 20889, USA. 2 IS0 8630-l : 1967 (E) The temperature and the relative humidity shall be measured in the air immediately surrounding th

24、e cartridge. The stray magnetic field at any point on the disk surface, including that resulting from the concentrating effect of the recording head, shall not exceed 4 000 A/m (50 Oe). 6.1.2 Operating environment Cartridges used for data interchange shall be operated under the following conditions:

25、 - temperature: 10 to 51,5 OC (50 to 125 OFI; - relative humidity: 20 to 80 %; - wet-bulb temperature: less than 29 OC (84 OFI. The temperature and the relative humidity shall be measured in the air immediately surrounding the cartridge. It is recom- mended that the rate of change of the temperature

26、 should not exceed 20 OC (36 OFI per hour. It is recommended that the following conditions are not exceeded : - temperature: -4Oto +51,5C(-40to +125OF); - maximum rate of temperature change: 20 OC (36 OFI per hour; - relative humidity: 8 to 90 %. There should be no deposit of moisture on or in the c

27、artridge. 6.1.6 Handling The cartridge shall stay out of its envelope for the shortest time possible. When handling the cartridge the operator shall not touch the exposed magnetic surfaces of the disk and shall avoid exposing the cartridge to direct sunlight, moisture and dust. 6.2 Materials 62.1 Ja

28、cket The jacket may be constructed from any suitable material. There shall be no deposit of moisture on or in the cartridge. The stray magnetic field at any point on the disk surface, including that resulting from the concentrating effect of the recording head, shall not exceed 4 000 A/m (50 Oe). 6.

29、1.3 Storage environment During storage the cartridges shall be kept under the following conditions : - temperature: 4 to 51,5 OC (40 to 125 OFI; - relative humidity: 8 to 80 %. Each cartridge shall be in an envelope and in an upright position. There shall be no deposit of moisture on or in the cartr

30、idge. The ambient stray magnetic field at any point on the disk sur- face shall not exceed 4 000 A/m (50 Oe). NOTE - Cartridges which have been stored at temperatures and humidities outside the operating conditions may exhibit degraded per- formance characteristics. Such cartridges should be subject

31、ed to a conditioning period of not less than 24 h within the operating environ- ment prior to use. 6.1.4 Transportation Responsibility for ensuring that adequate precautions are taken during transportation shall be with the sender. During trans- portation the cartridge shall be in its envelope and i

32、n a protec- tive package. The latter shall be free from dust or extraneous matter. It shall have a clean interior and construction to minimize ingress of dust and moisture. It is recommended that a sufficient space exists between cartridge and outer surface of the final container, so that risk of da

33、mage due to stray magnetic fields will be negligible. 6.2.2 Liner The material of the liner shall be able to retain dust without damage to the disk. 6.2.3 Disk The disk may be constructed from any suitable material (for example bi-axially oriented polyethylene terephthalate) coated on both sides wit

34、h a strong and flexible layer of magnetic material (for example Co-yFe203). 6.2.4 Envelope The envelope may be manufactured from any suitable material (for example paper). 6.3 Direction of rotation The direction of rotation shall be counterclockwise when look- ing at side 0. 7 Dimensional characteri

35、stics The dimensional characteristics listed in the following clauses are indicated in figures 4 to 7. Figure 4 - Jacket dimensions, shows the jacket. Figure 5 - Cartridge thickness, shows a partial cross- section of the jacket. Figure 6 - Disk dimensions, shows the disk. Figure 7 - Disk thickness,

36、shows a cross-section of the disk. All dimensions are referred to the reference edge of the cartridge (see figure 4). IS0 8630-l : 1987 (E) 7.1 Jacket 7.1.1 Form The jacket shall have a square form with angles of 90 f 30 and a side length I, = 133.3 + 0,4 mm (5.250 k 0.015 in) 7.1.2 Thickness 7.1.2.

37、1 Jacket wall and liner In an area defined by rl = 35 mm (1.38 in) r2 = 50 mm (1.97 in) and with a probe having a diameter of 15 mm (0.59 in) applied against the cartridge with a force of 1 N (3.6 ozf), the thickness of the jacket wall and liner shall be el = 0,45 f. 0,15 mm (0.018 f 0.006 in) 7.1.2

38、.2 Cartridge The overall thickness of the cartridge shall be (see also 7.1.7) 1,2 mm (0.047 in) e22,1 mm (0.083 in), when measured according to clauses A.1 and A.2 of annex A. The cartridge shall fall freely through a gauge with a 2,60+$ mm (0.102:8;% in) wide opening having flat, vertical walls and

39、 a depth of 150 mm (5.9 in). 7.1.3 Central windows The central windows shall have a diameter d, = 39,7 + 0.2 mm (1.56 f 0.01 in) The position of their centre is defined by 1, = 66,65 f 0,30 mm (2.624 f 0.012 in) 7.1.4 Index windows 7.1.4.1 Location The centre of the index windows shall be defined by

40、 13 = 42.10 + 0,25 mm (1.657 + 0.010 in) f4 = 60,OO f 0.25 mm (2.362 f 0.010 in) 7.1.4.2 Diameter The diameter of the index windows shall be defined by d2 = 6,35 If: 0,20 mm (0.250 f 0.008 in) 7.1.5 Head windows 7.1.5.1 Location The location of the lowest point of the head windows shall be defined b

41、y I, = 3,30 f 0,25 mm (0.130 f 0.010 in) 7.1.5.2 Dimensions The width of the head windows shall be Is = 12.7 f 0,2 mm (0.500 f 0.008 in) The nominal radius of their ends shall be r3 = 6,35 mm (0.250 in) Their length shall be I, = 35,00 f 0,25 mm (1.378 f 0.010 in) 7.1.6 Reference edge profile Within

42、 an area defined by Is = 25 mm (1.0 in) the Reference Edge shall have a convex profile, for example be rounded off with one or more radii of 0,3 mm min. (0.012 in min.). 7.1.7 Construction of the jacket If the jacket utilizes flaps, their width shall not exceed I, = 12 mm (0.47 in) The total thickne

43、ss e2 of the cartridge with flaps shall satisfy the conditions of 7.1.2.2 (see annex A). 7.1.8 Notches Two notches may be provided along the Reference Edge. If provided, they shall be entirely contained within areas defined by: fle = 48,0 mm min. (1.89 in min.) I, = 68.0 mm max. (2.28 in max.) iI2 =

44、 75.0 mm min. (2.95 in min.) il3 = 85,5 mm max. (3.37 in max.) I, = 2,0 mm max. (0.08 in max.) 4 IS0 8630-l : 1987 (El 7.1.9 Write-enable notch The position and size of the write-enable notch shall be defined by: frs = 96.5 f 0,2 mm (3.799 + 0.008 in) I, = 6.35 + 0,13 mm (0.25 f 0.005 in) 12, = 3,8

45、+ 0,2 mm (0.150 f 0.008 in) Writing is inhibited by covering the notch with a material of suf- ficient stiffness and/or opacity. 7.2 Liner The liner shall extend across the recording area (7.3.4). However, no part of the liner shall protrude by more than 0,5 mm (0.019 in) into the openings of the ja

46、cket. 7.3 Disk 7.3.1 Diameter The external diameter of the disk shall be d3 = 130.2 f 0,2 mm (5.125 f 0.008 in) The inner diameter of the disk shall be d4 = 28,575 + 0,025 mm (1.125 + 0.001 in) 7.3.2 Thickness The thickness of the disk shall be e3 = 0,080 f 0,010 mm (0.003 0 f 0.000 4 in) 7.3.5 Side

47、s For convenience of description the two sides are defined as Side 0 and Side 1; they are shown in figures 1 to 4 and figure 8. 8 Physical characteristics 8.1 Flammability The cartridge shall be made from materials that, if ignited from a match flame, do not continue to burn in a still carbon dioxid

48、e atmosphere. 8.2 Coefficient of linear thermal expansion of the disk The coefficient of thermal expansion of the disk shall be (17 * 8) x 10-e per degree Celsius 8.3 Coefficient of linear hygroscopic expansion of the disk The coefficient of hygroscopic expansion of the disk shall be (0 to 15) x 10-

49、a per percent of relative humidity 8.4 Opacity 6.4.1 Opacity of the jacket The jacket shall have a light transmittance of less than 1 % using an LED with a nominal wavelength of 940 nm as the radiation source when measured according to annex B. Write enable notch covering means are included in the jacket for opacity. 6.4.2 Opacity of