ANSI INCITS 137-1988 Information Technology - One- and Two-Sided Unformatted 90-mm (3.5-in) 5 3-tpmm (135-tpi) Flexible Disk Cartridge for 7958 bpr Use - General Physical and Magne.pdf

《ANSI INCITS 137-1988 Information Technology - One- and Two-Sided Unformatted 90-mm (3.5-in) 5 3-tpmm (135-tpi) Flexible Disk Cartridge for 7958 bpr Use - General Physical and Magne.pdf》由会员分享，可在线阅读，更多相关《ANSI INCITS 137-1988 Information Technology - One- and Two-Sided Unformatted 90-mm (3.5-in) 5 3-tpmm (135-tpi) Flexible Disk Cartridge for 7958 bpr Use - General Physical and Magne.pdf（36页珍藏版）》请在麦多课文档分享上搜索。

1、kNSI INCITS 137-1988/AMI-1999 formerly ANSI X3.137- 1988/AM1-1999) (Supplement to ANSI INCITS 13 7-1 988 formerly ANSI X3.137-1988) for Information Technology - One- and Two-sided, Unformatted, 90-mm (3.5- in) 5,3-tpmm (1 35-tp9, Flexible Disk Cartridge for 7958 bpr Use - General, Physical and Magne

2、tic Requirements Developed by Where IT all begins ANSI X3.137-I 988/AM1-1999 supplement to ANSI X3.137-1988 for Information Technology - One- and Two-sided, Unformatted, 90-mm (3.5-in) 5,3- tpmm (135-tpi), Flexible Disk Cartridge for 7958 bpr Use - General, Physical and Magnetic Requirements Approve

3、d June 21, 1999 Secretariat: Information Technology Industry Council ) Page 1 of 3 pages Change fhe definifions in clause 3 fo read as follows: 3.1 measured peak-to-peak over the whole track. 3.2 3.3 3.4 transmitted to the disk. It ensures centering of the disk on the drive shaft in a unique angular

4、 position. 3.5 with the magnetic head(s). 3.6 3.7 protection from abrasion. 3.8 as the standard for reference fields, signal amplitudes, resolution, peak shift, and overwrite. Track O0 Track 79 on both sides are declared as reference tracks. The reference tracks are calibrated at 300 r/min. NOTE: Th

5、is Master Standard has been established by the Physikalisch-Technische Bundesanstalt (PTB). (See 3.12 for further information.) Average Signal Amplitude. The arithmetically averaged value for a track of the output voltages Cartridge. An assembly of recording disk and case. Case. A protective enclosu

6、re including a shutter mechanism and a write-inhibit hole. Hub. A centering and referencing device attached to the center of the disk that allows torque to be Contact. An operating condition in which the magnetic surfaces of the disk are in physical contact Index. The point on a track that determine

7、s the beginning and end of the track. Liner. Suitable material positioned between the case and the disk to provide cleaning action and Master Standard Reference Flexible Disk Cartridge. A reference flexible disk cartridge selected 3.9 I1 O nm and a half power bandwidth of 50 nm, maximum, and a silic

8、on photovoltaic cell with an appropriate aperture operating in the short circuit mode, spaced 10 mm (0.39 in) apart, with their optical axes parallel and contained in a suitable light-tight cover. 3.10 Recording Disk. A flexible disk that accepts and retains, on the specified side or sides, magnetic

9、 signals intended for inputloutput and storage purposes. 3.11 Reference Field. The typical field of the Master Standard Reference Flexible Disk Cartridge. There are two Reference fields. one for each side. Optical System. A system consisting of a light-emitting diode with a peak power point at 940 m

10、m An American National Standard implies a consensus of those substantially concerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The exist- ence of an American National Standard does not in any res

11、pect preclude anyone, whether he has approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the stan- dard. American National Standards are subject to periodic review and users are cautioned to obtain the latest editions

12、. The American National Standards Institute does not develop standards and will in no circumstances give an interpretation of any American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an Amer- ican National Standard in the name of the America

13、n National Standards Institute. CAUTION NOTICE: This American National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute require that action be taken to reaffirm, revise, or withdraw this standard no later than five years from the date of a

14、pproval. Purchasers of American National Standards may receive current information on all stan- dards by calling or writing the American National Standards Institute. Copyright O 1999 by Information Technology Industry Council (ITI), 1250 Eye Street NW, Washington, DC 20005 Page 2 of 3 pages 3.12 Se

15、condary Standard Reference Flexible Disk Cartridge. A flexible disk cartridge, the performance of which is known and stated in relation to that of the Master Standard Reference Flexible Disk Cartridge. NOTE: Secondary Standard Reference Flexible Disk Cartridges can be ordered under part number RM 88

16、60 from PTB Lab 1.41, Physikalisch-Technische Bundesanstalt (PTB), Bundesallee 100, D-3300 Braunschweig, Germany, F.R. It is intended that these be used for calibrating further cartridges for use in routine calibration. 3.13 Shutter. A device that uncovers the head windows upon insertion and automat

17、ically covers them upon removal from the drive. 3.14 Side Number. Side O is the side engaged by the spindle. Side 1 is the opposite side. 3.15 Standard Reference Amplitudes (SRAS). The average signal amplitudes derived from the reference tracks of the Master Standard Reference Flexible Disk Cartridg

18、e using the Test Recording Current. There are four SRAs, two for each side: SRA-If is the Average Signal Amplitude from a recording using Test Frequency If at Track 00; SRA-2f is the Average Signal Amplitude from a recording using Test Frequency 2f at Track 79. 3.16 Test Recording Current. The curre

19、nt between 148% and 152% of the current that produces the Reference field at Test Frequency If on Track OO. There are two Test Record Currents, one for each side. 3.17 Test Recording Frequency (at the Recording Head). The number of flux transitions per unit of time, usu- ally expressed as flux trans

20、itions per second (ftps) (1 Hz = 2 ftps). 3.18 Transmittance. The radiant energy that passes through a sample, divided by the radiant energy that is inci- dent upon the sample. Transmittance is usually multiplied by 100 and is called percent transmittance (PT). The maximum allowable transmittance sh

21、all be defined by the reading obtained with neutral density filter with a known transmittance between 0.95% and 1.05%, calibrated at a 940-nm wavelength when used in place of the sample. 3.19 Typical Field. The minimum field that causes a signal output equal to 95% of the maximum Average Signal Ampl

22、itude in the plot of Average Signal Amplitude against recording field at the specified track and flux transition density. In 5.2.1, change fhe inch conversion of fhe forque range fo read: (0.071 to 0.354 ozf in). In 6.3.1, Nominal Locafions, change fhe formula fo calculafe fhe nominal radius R of fh

23、e cenferline of all fracks from: R = X-0,1875 N mm X (R=z4 i 7.3818 x 10-3N in where X = 393 mm (1.5551 in) for side O X = 38,O mm (1.4961 in) for side 1 N =track number R = X-0,1875 N mm (R = X - 7.3818 x IOp3 N in) X = 393 mm (1.5551 in) for side O X = 38,O mm (1.4961 in) for side 1 N =track numbe

24、r fo: where In 8.1.5, Ovemrife, change fhe lasf senfence from: “At the outermost track, the ratio shall be not more than 125% of the value of the same ratio for the Master Standard Reference Flexible Disk Cartridge.” fo: “At the outermost track, the ratio shall be not more than 150% of the value of

25、the same ratio for the Master Stan- dard Reference Flexible Disk Cartridge.” ANSI X3.137-I 988/AM1-1999 Page 3 of 3 pages In fhe fable in Figure 4, Side 1 View and Hub Defail, change fhe values of references N and P fo read as follows: Reference Dimension Tolerance (I) mm in mm in N 31,15 1.2264 max

26、 max P 1,36 0.054 0,1 0.004 In Appendix E, Peak Shiff Measuremenf, change fhe fexf of Secfion E2 fo read as follows: E2. Definition T- T Peak Shift = - 2 where T = the mean period of the peaks of the reproduced waveform T = the period of the peak of the 2f pattern (2 microseconds at 300 r/min) The p

27、eak shift value of the disk under test, expressed in percentage should be: pt ps - x Kx 100 where Pt = the peak shift value obtained for the disk under test P, = the peak shift value obtained for the Secondary Standard Reference Flexible Disk Cartridge K = the calibration factor of the Secondary Sta

28、ndard Reference Flexible Disk Cartridge ANSI X3.137-I 988/AM1-1999 ANSI X3.139 88 09241i50 0018537 1 ANSI X3.137-1988 for information syst _ ANSI X3.137 88 m 0724350 0038538 3 m American National Approval of an American National Standard requires verification by ANSI that the re- quirements for due

29、process, consensus, and other criteria for approval have been met by the standards developer. Standard Consensus is established when, in the judgment of the ANSI Board of Standards Review, substantial agreement has been reached by directly and materially affected interests. Sub- stantial agreement m

30、eans much more than a simple majority, but not necessarily unanim- ity. Consensus requires that all views and objections be considered, and that a concerted effort be made toward their resolution. The use of American Natio,nal Standards is completely voluntary; their existence does not in any respec

31、t preclude anyone, whether he hasapproved the standards or not, from man- ufacturing, marketing, purchasing, or using products, processes. or procedures not con- forming to the standards. The American National Standards Institute does not develop standards and will in no cir- cumstances give an inte

32、rpretation of any American National Standard. Moreover, no per- son shall have the right or authority to issue an interpretation of an American National Standard in the name of the American National Standards Institute. Requests for inter- pretations should be addressed to the secretariat or sponsor

33、 whose name appears on the title page of this standard. CAUTION NOTICE: This American National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute require that action be taken periodically to reaffirm, revise, or withdraw this standard. Purch

34、asers of American National Standards may receive current information on all standards by calling or writing the American Nationabstandards Institute. Published by American National Standards Institute 1430 Broadway, New York, New York 10018 Copyright O 1988 by American National Standards Institute,

35、Inc All rights resewed. No part of this publication may be reproduced in any forni, in an ekctronic retrieval system or otherwise, without the prior written permission of the publisher. Printed in the United States of America ANSI X3.337 88 0724350 0038537 5 = ANSI X3.137-1988 American National Stan

36、dard for Information Systems - One- and Two-sided, Unformatted, 90-mm (3.5-in), 5,3-tpmm (I 35-tpi), Flexible Disk Cartridge for 7958 bpr Use - General, Physical, and Magnetic Requirements Secretariat Computer and Business Equipment Manufacturers Association Approved January 29,1988 American Nationa

37、l Standards Institute, Inc a (This Foreword is not part of American National Standard X3.137-1988.) This standard presents, for the purpose of physical and magnetic interchange, a one- and two-sided 90-mm (3.5-in) (nominal) flexible disk cartridge for 7958 bits per radian (bpr) use as required to ac

38、hieve unformatted disk cartridge inter- change among disk drives using 80 tracks per side and associated information processing systems. Subsequent related standards may contain specifications that differ from this standard as a result of the normal evolution of the product. Original source dimensio

39、ns for this standard were in the International System of units (SI), and reconversion from U.S. customary unit equivalents back to SI units should not be performed. This standard was developed by the X3B8 Technical Committee on Flexible Disks, which consists of a group of experienced and knowledgeab

40、le persons uni- quely qualified with respect to the flexible disk cartridge and its performance re- quirements. Although most members are affiliated with industry or government organizations, this standard represents the sum of individual efforts. Suggestions for improvement of this standard will be

41、 welcome. They should be sent to the Computer and Business Equipment Manufacturers Association, 3 11 First Street, NW, Washington, DC 20001. Foreword This standard was processed and approved for submittal to ANSI by Accredited Standards Committee on Information Processing Systems, X3. Committee ap-

42、proval of the standard does not necessarily imply that all members voted for its approval. At the time it approved this standard, the X3 committee had the fol- lowing members: Richard Gibson, Chair Donald C. Loughry, Vice-Chair Catherine A. Kachurik, Administrative Secretary Organizafion Represented

43、 Nome of Representative American Library Association American Nuclear Society Geraldine C. Main AMPIncorporated EdwardKelly Association of the Institute for Certification of AT&T . PaulD. Bartoli Thomas F. Frost (Alt) Control Data Corporation Charles E. Cooper Keith Lucke (Alt) Cooperating Users of

44、Borroughs Equipment . Thomas Easterday Donald Miller (Alt) Data General Corporation Lee Schiller Lyman Chapin (Alt) Data Processing Management Association Wallace R. McPherson (Alt) Digital Equipment Computer Users Society Digital Equipment Corporation . Gary S. Robinson EastmanKodak GaryHaines Gene

45、ral Electric Company GUIDE International . Frank Kirshenbaum . Paul Peters Sally Hartzell (Alt) Computer Professionals Thomas M. Kurihara Ward Arrington . Dennis Perry Delbert L. Shoemaker (Alt) Charleton C. Bard (Alt) William R. Kruesi (Alt) Sandra Swartz Abraham (Alt) . Richard W. Signor Hewlett-P

46、ackard . Donald C. Loughry Honeywell Bull David M. Taylor IBM Corporation . Mary Anne Gray Robert H. Follett (Alt) ! I ANSI X3.137 88 0724150 0018541 3 = Organization Represen fed IEEE Computer Society . Sava I. Sherr Name of Representative Thomas A. Varetoni (Alt) Helen Wood (Alt) Robert L. Fink (A

47、lt) Mike Kaminski (Alt) Lawrence Berkeley Laboratory . David F. Stevens MAPROP . James D. Converse Moore Business Forms Delmer H. Oddy National Bureau of Standards Robert E. Rountree National Communications System . Dennis Bodson NCR Corporation . William E. Snyder OMNICOM HaroldC. Folts Prime Compu

48、ter, Inc . Arthur Norton Railinc Corporation . Moncure N. Lyon Recognition Technology Users Association Herbert F. Schantz G. W. Wetzel (Alt) Scientific Computer Systems Corporation Carl Haberland (Alt) SHARE, Inc Thomas B. Steel Robert A. Rannie (Alt) 3M Company . Paul D. Jahnke Travelers Insurance

49、 Companies, Inc Joseph T. Brophy Unisys . Marvin W. Bass Stanley Fenner (Alt) U.S. Department of Defense Belkis bong-Hong (Alt) U.S. General Services Administration . William C. Rinehuls Larry L. Jackson (Alt) VIM ChrisTanner Madeleine Sparks (Alt) VISA U.S.A. . Jean T. McKenna Patty Greenhalgh (Alt) Xerox Corporation John L. Wheeler Roy Pierce (Alt) James H. Burrows (Alt) George W. White (Alt) A. Raymond Daniels (Alt) Catherine Howelis (Alt) Donna A. Poulack (Alt) James A. Baker Fred Virtue Technical Committee X3B8 on Flexible Disks, which developed this standard, had the following member