ANSI IEEE 1101.11-1998 Standard for Mechanical Rear Plug-In Units Specifications for Microcomputers Using IEEE 1101.1 and IEEE 1101.10 Equipment Practice (IEEE Computer Society Doc.pdf

《ANSI IEEE 1101.11-1998 Standard for Mechanical Rear Plug-In Units Specifications for Microcomputers Using IEEE 1101.1 and IEEE 1101.10 Equipment Practice (IEEE Computer Society Doc.pdf》由会员分享，可在线阅读，更多相关《ANSI IEEE 1101.11-1998 Standard for Mechanical Rear Plug-In Units Specifications for Microcomputers Using IEEE 1101.1 and IEEE 1101.10 Equipment Practice (IEEE Computer Society Doc.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、Recognized as anAmerican National Standard (ANSI)The Institute of Electrical and Electronics Engineers, Inc.345 East 47th Street, New York, NY 10017-2394, USACopyright 1998 by the Institute of Electrical and Electronics Engineers, Inc.All rights reserved. Published 1998. Printed in the United States

2、 of America.ISBN 0-7381-0179-6No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher.IEEE Std 1101.11-1998 (R2008)IEEE Standard for Mechanical RearPlug-in Unites Specifications for Microcomputer

3、s Using IEEE 1101.1and IEEE 1101.10 Equipment PracticeSponsorBus Architecture Standards Committeeof theIEEE Computer SocietyReaffirmed 31 January 2008Approved 21 May 1998IEEE-SA Standards BoardApproved 5 February 1999American National Standards InstituteAbstract: Additional dimensions that will ensu

4、re mechanical interchangeability of subracks andplug-in units based on IEEE P1101.1 (D1.0, 1997), IEEE Std 1101.10-1996, and environmentalrequirements of IEC 61587-1 (May 1998-Draft) are specified.Keywords: backplane, compatibility, connector, inline configuration, inspection dimension, plug-inunit,

5、 printed board, shroud, subrackIEEE Standardsdocuments are developed within the IEEE Societies and the Standards Coordinat-ing Committees of the IEEE Standards Association (IEEE-SA) Standards Board. Members of thecommittees serve voluntarily and without compensation. They are not necessarily members

6、 of theInstitute. The standards developed within IEEE represent a consensus of the broad expertise on thesubject within the Institute as well as those activities outside of IEEE that have expressed an inter-est in participating in the development of the standard.Use of an IEEE Standard is wholly vol

7、untary. The existence of an IEEE Standard does not implythat there are no other ways to produce, test, measure, purchase, market, or provide other goods andservices related to the scope of the IEEE Standard. Furthermore, the viewpoint expressed at thetime a standard is approved and issued is subject

8、 to change brought about through developments inthe state of the art and comments received from users of the standard. Every IEEE Standard is sub-jected to review at least every ve years for revision or reafrmation. When a document is morethan ve years old and has not been reafrmed, it is reasonable

9、 to conclude that its contents,although still of some value, do not wholly reect the present state of the art. Users are cautioned tocheck to determine that they have the latest edition of any IEEE Standard.Comments for revision of IEEE Standards are welcome from any interested party, regardless ofm

10、embership afliation with IEEE. Suggestions for changes in documents should be in the form of aproposed change of text, together with appropriate supporting comments.Interpretations: Occasionally questions may arise regarding the meaning of portions of standards asthey relate to specic applications.

11、When the need for interpretations is brought to the attention ofIEEE, the Institute will initiate action to prepare appropriate responses. Since IEEE Standards rep-resent a consensus of all concerned interests, it is important to ensure that any interpretation hasalso received the concurrence of a b

12、alance of interests. For this reason, IEEE and the members of itssocieties and Standards Coordinating Committees are not able to provide an instant response tointerpretation requests except in those cases where the matter has previously received formalconsideration. Comments on standards and request

13、s for interpretations should be addressed to:Secretary, IEEE-SA Standards Board445 Hoes LaneP.O. Box 1331Piscataway, NJ 08855-1331USAAuthorization to photocopy portions of any individual standard for internal or personal use isgranted by the Institute of Electrical and Electronics Engineers, Inc., p

14、rovided that the appropriatefee is paid to Copyright Clearance Center. To arrange for payment of licensing fee, please contactCopyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA;(978) 750-8400. Permission to photocopy portions of any individual standard for educat

15、ional class-room use can also be obtained through the Copyright Clearance Center.Note: Attention is called to the possibility that implementation of this standard mayrequire use of subject matter covered by patent rights. By publication of this standard,no position is taken with respect to the exist

16、ence or validity of any patent rights inconnection therewith. The IEEE shall not be responsible for identifying patents forwhich a license may be required by an IEEE standard or for conducting inquiries intothe legal validity or scope of those patents that are brought to its attention.Copyright 1998

17、 IEEE. All rights reserved.iiiIntroduction(This introduction is not part of IEEE Std 1101.11-1998, IEEE Standard for Mechanical Rear Plug-in Units Specica-tions for Microcomputers Using IEEE 1101.1 and IEEE 1101.10 Equipment Practice.)Despite the push for metrication, the Euroboard (19 in based) con

18、tinues to be the leading choice for theindustrial mechanical equipment practice, and is accepted throughout the world for all kinds of electronicsapplications. Among these are all major bus architectures, such as VME, CompactPCI, etc.This is why the Computer Societys Technical Committee on Microcomp

19、uters and Microprocessors found itappropriate to create an IEEE standard which further expands upon IEEE P1101.1 (D1.0, 1997) and the IEC60297-. series of standards, Dimensions of Mechanical Structures of the 482.6 mm (19 in) Series, IEC60297-3 (1984-01) and IEC 60297-4 (1995-03) for rear plug-in un

20、its.This standard is an extension of IEEE P1101.1 (D1.0, 1997) and IEEE Std 1101.10-1996 (submitted to theIEC) and denes the mechanical rear plug-in unit sizes and interface details. At the time this standard was completed, the P1101.11 Working Group had the following membership:Eike Waltz,ChairFran

21、k Hom,SecretaryThe following persons were on the balloting committee:Ralf BehrensPaul DenommeRobert W. DowningJean-Jacque DumontWayne P. FischerTad KubicPaul MazuraDavid MoorePeter G. OdellGunter PapeElwood T. ParsonsHolly ShernskiMichael G. ThompsonSue WongDavid L. WrightGhassan A. AbbasMalcolm J.

22、AirstRay S. AldermanHarry A. AndreasKeith D. AnthonyEdmund H. BaulsirMartin BlakeRalf BokaemperDavid BrearleyCharles BrillC. H. ChenRobert W. DowningJean-Jacque DumontWayne P. FischerKenneth C. HeckRoger HinsdaleFrank HomConrad A. LaurvickGerald E. LawsRollins LinserGary S. ManchesterJoseph R. Marsh

23、allThanos MentzelopoulosGene E. MilliganKlaus-Dieter MuellerMichael MunroeJoe P. NorrisPeter G. OdellElwood T. ParsonsHermann H. StrassMichael G. ThompsonRobert C. TripiBruce WallaceDavid L. WrightivCopyright 1998 IEEE. All rights reserved.The nal conditions for approval of this standard were met on

24、 21 May 1998. This standard was conditionallyapproved by the IEEE-SA Standards Board on 19 March 1998, with the following membership:Richard J. Holleman,ChairDonald N. Heirman,Vice ChairJudith Gorman,Secretary*Member EmeritusCatherine K.N. BergerIEEE Standards Project EditorCompactPCI is a registere

25、d trademark of the PCI Industrial Computer Manufacturers Group.Satish K. AggarwalClyde R. CampJames T. CarloGary R. EngmannHarold E. EpsteinJay Forster*Thomas F. GarrityRuben D. GarzonJames H. GurneyJim D. IsaakLowell G. JohnsonRobert KennellyE. G. Al KienerJoseph L. Koepnger*Stephen R. LambertJim L

26、ogothetisDonald C. LoughryL. Bruce McClungLouis-Franois PauRonald C. PetersenGerald H. PetersonJohn B. PoseyGary S. RobinsonHans E. WeinrichDonald W. ZipseCopyright 1998 IEEE. All rights reserved.vContents1. Overview 11.1 Scope 11.2 Purpose. 22. References 23. Terminology. 33.1 Abbreviations. 33.2 S

27、pecial word usage 34. General arrangement 45. Relationships of front and rear plug-in units . 55.1 The in-line configuration, non-EMC and EMC. 56. Rear mounted plug-in unit printed board (Euroboard) sizes . 66.1 Board height. 76.2 Board depth 76.3 Rear mounted plug-in unit inspection dimensions. 77.

28、 Connector orientation, pin labeling, and printed board component view 98. Subrack rear attachment plane. 109. Rear backplane mounted plug-in unit fixed connector relationship 1110. Rear subrack connector (backplane mounted) shroud orientation. 1210.1 Connector shroud orientation. 1211. Backplane bo

29、w and support. 1212. Connector performance 1313. Connector alignment 1314. Rear mounted plug-in unit cooling consideration1315. Front and rear plug-in unit front panel protective ground . 1315.1 Mechanical design . 1315.2 Requirement. 1315.3 Resistance 1315.4 Minimum galvanic compatibility and conta

30、ct operations 1415.5 Pass criteria 14Annex A (normative) Inspection Dimensions for Subracks and Associated Plug-in Units inAccordance with IEEE 1101.1, IEEE 1101.10 and IEEE Draft P1101.11 Using theIEC 61076-4-101 Connector Series. 15Annex B (informative) Bibliography 21Copyright 1998 IEEE. All righ

31、ts reserved.1IEEE Standard for Mechanical Rear Plug-in Units Specications for Microcomputers Using IEEE 1101.1 and IEEE 1101.10 Equipment Practice1. Overview1.1 ScopeThis standard may be applied in all elds of electronics where equipment and installations are required toconform to the 482.6 mm (19 i

32、n) equipment practice based on IEEE P1101.1 (D1.0, 1997),1IEEE Std1101.10-1996, IEC 60297-3 (1984-01) B42, and IEC 60297-4 (1995-03) B5 for mounting in equipmentaccording to ANSI/EIA 310-D-1992 B1 and IEC 60297-1 (1986-01) B3 (see Figure 1). This standardcovers subracks equipped with front mounted p

33、lug-in units in accordance with IEEE P1101.1 (D1.0, 1997)and IEEE Std 1101.10-1996, and provides for additional rear mounted plug-in units in the same subrack.This standard permits other suitable IEC connector-related dimensions to be added (see Annex A).1.1.1 Dimensions of printed boardsThis standa

34、rd covers an additional range of printed board (PB) sizes suitable for subrack rear mounted plug-in units based on IEEE P1101.1 (D1.0, 1997), IEEE Std 1101.10-1996, IEC 60297-3 (1984-01) B4, andIEC 60297-4 (1995-03) B5 for mounting in equipment according to ANSI/EIA 310-D-1992 B1 and IEC60297-1 (198

35、6-09) B3.1.1.2 Dimensions of subracksThis standard covers additional dimensions, according to IEEE P1101.1 (D1.0, 1997) and IEEE Std1101.10-1996, for subracks with rear mounted plug-in units.1.1.3 Dimensions of backplanesThis standard covers limits of backplane thickness, according to IEEE P1101.1 (

36、D1.0, 1997) and IEEE Std1101.10-1996, when installed in subracks with rear mounted plug-in units.1Information on references can be found in Clause 2.2The numbers in brackets preceded by the letter B correspond to those of the bibliography in Annex B.IEEEStd 1101.11-1998 IEEE STANDARD FOR MECHANICAL

37、REAR PLUG-IN UNITS SPECIFICATIONS FOR2Copyright 1998 IEEE. All rights reserved.1.1.4 Choice of connectorsThis standard refers only to connectors in accordance with IEC 60603-2 (1995-09) B6 and as referenced inIEEE P1101.1 (D1.0, 1997) and IEEE Std 1101.10-1996. Other IEC connectors may be used by th

38、emselvesor mixed with IEC 60603-2 connectors. This standard denes inspection dimensions required for IEC60603-2 and IEC 61076-4-1xx connectors. Inspection dimensions for the IEC 61076-4-101 series of con-nectors may be found in Annex A. This standard also denes the difference between a front plug-in

39、 unit con-nector and a rear plug-in unit connector (see Figure 6).1.1.5 Rear connector shroudsThis standard denes the dimensions of compatible connector shrouds.1.1.6 Front and rear plug-in unit front panel protective groundThis standard denes mechanical interface and electrical test requirements fo

40、r input/output (I/O) plug-in unitprotective ground protection with reference to IEC 60950 (1991-10) B8.1.2 PurposeThe purpose of this standard is to specify additional dimensions that, when followed, will ensure mechanicalinterchangeability of subracks and plug-in units based on IEEE Std 1101.10-199

41、6 and the environmentalrequirements of IEC 61587-1 (May 1998-Draft) and IEC 61587-3 (May 1998-Draft).NOTEIEEE P1101.1 (D1.0, 1997), IEC 60297-3 (1984-01), and IEC 60297-4 (1995-03) subrack systems not comply-ing with these additional standard requirements have limited compatibility.2. ReferencesThis

42、 standard shall be used in conjunction with the following publications. When they are superseded by anapproved revision, the revision shall apply. The users of this standard are required to be familiar with IEEE P1101.1 (D1.0, 1997) and IEEE Std1101.10-1996.IEC 61587-1 (May 1998-Draft), Climatic, me

43、chanical tests and safety aspects for racks, subracks for theIEC 60917-.and IEC 60297-. Series.3IEC 61587-3 (May 1998-Draft), Electromagnetic shielding performance tests for cabinets, racks and sub-racks for the IEC 60917-. and 60297-.Series.IEEE P1101.1 (D1.0, 1997), DRAFT Standard for Mechanical C

44、ore Specication for MicrocomputersUsing IEC (60)603.2 Connectors.4IEEE Std 1101.10-1996, IEEE Standard for Additional Mechanical Specications for MicrocomputersUsing the IEEE 1101.1-1991 Equipment Practice.53IEC publications are available from IEC Sales Department, Case Postale 131, 3, rue de Varemb

45、, CH-1211, Genve 20, Switzerland/Suisse. IEC publications are also available in the United States from the Sales Department, American National Standards Institute, 11West 42nd Street, 13th Floor, New York, NY 10036, USA.4This IEEE standards project was not approved by the IEEE Standards Board at the

46、 time this publication went to press. For informationabout obtaining a draft, contact the IEEE.5IEEE publications are available from the Institute of Electrical and Electronics Engineers, 445 Hoes Lane, P.O. Box 1331, Piscataway,NJ 08855-1331, USA.IEEEMICROCOMPUTERS USING IEEE 1101.1 AND IEEE 1101.1

47、0 EQUIPMENT PRACTICE Std 1101.11-1998Copyright 1998 IEEE. All rights reserved.33. Terminology3.1 Abbreviations and acronymsDa dimension between front panel mounting hole and connector mounting holeDb printed board depth dimensionDc inspection dimension for subrack front mounted PiUsDg dimension betw

48、een front panel mounting hole and rear end solder side cover mounting holesDT 2 inspection dimension of plug-in unit assemblyEMC electromagnetic compatibilityFSC xed subrack connectorHP horizontal pitch of 5.08 mmI/O input/outputPB printed boardPFC plug-in unit free connectorPiU plug-in unitRDc insp

49、ection dimension for subrack rear mounted PiUsRDx inspection dimension for shroud positioningRFC rear free connectorRSC rear subrack connector (backplane mounted)U subrack height measured in units of 44.45 mm (1.75 in)3.2 Special word usagemay: A keyword indicating exibility of choice with no implied preference.shall: A keyword indicating a mandatory requirement. should: A keyword indicating exibility of choice with a strongly preferred plementary:A keyword indicating that there is no standard as yet