ANSI IEC C78.62035-2004 Discharge Lamps (excluding fluorescent lamps) - Safety Specifications《放电灯(不包括荧光灯).安全规范》.pdf

《ANSI IEC C78.62035-2004 Discharge Lamps (excluding fluorescent lamps) - Safety Specifications《放电灯(不包括荧光灯).安全规范》.pdf》由会员分享，可在线阅读，更多相关《ANSI IEC C78.62035-2004 Discharge Lamps (excluding fluorescent lamps) - Safety Specifications《放电灯(不包括荧光灯).安全规范》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 ANSI_IEC C78.62035-2004 American National Standard for Electric Lamps Discharge Lamps (Excluding Fluorescent Lamps) Safety Specifications Copyright National Electrical Manufacturers Association Provided by IHS under license with NEMANot for ResaleNo reproduction or networking permitted without lice

2、nse from IHS-,-,-Copyright National Electrical Manufacturers Association Provided by IHS under license with NEMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ANSI_IEC C78.620352004 Revision ANSI_IEC C78.62035-2002 American National Standard Approved: July 15, 200

3、4 Secretariat: ANSLG -National Electrical Manufacturers Association for electric lamps -Discharge Lamps (Excluding Fluorescent Lamps) Safety Specifications Copyright 2004 by American National Standard Lighting Group NEMA Copyright National Electrical Manufacturers Association Provided by IHS under l

4、icense with NEMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ANSI_IEC C78.62035-2004 American National Standard Approval of an American National Standard requires verification by ANSI that the requirements for due process, consensus, and other criteria for appro

5、val have been met by the standards developer. An American National Standard implies a consensus of those substantially concerned with its scope and provisions. Consensus is established when, in the judgment of the ANSI Board of Standards Review, substantial agreement has been reached by directly and

6、 materially affected interests. Substantial agreement means much more than a simple majority, but not necessarily unanimity. Consensus requires that all views and objections be considered, and that a concerted effort be made toward their resolution. The existence of an American National Standard doe

7、s not in any respect preclude anyone, whether s/he has approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standards. It is intended as a guide to aid the manufacturer, the consumer, and the general public. The Am

8、erican National Standards Institute does not develop standards and will in no circumstances give an interpretation of any American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an American National Standard in the name of the American National

9、 Standards Institute. Requests for interpretations should be addressed to the Committee Secretariat referred to on the title page. CAUTION NOTICE: This American National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute require that action

10、be taken periodically to reaffirm, revise, or withdraw this standard. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute. Printed and distributed by: Information Handling Services/Global Engineeri

11、ng Documents 15 Inverness Way East, Englewood, CO 80112-5776 Under Contract with National Electrical Manufacturers Association Copyright g2112004 by American National Standard Lighting Group In Affiliation with National Electrical Manufacturers Association All rights reserved. No part of this public

12、ation may be reproduced in any form, in an electronic retrieval system or otherwise, without prior written permission of the publisher. Printed in the United States of America Copyright 2004 by American National Standard Lighting Group NEMA 2Copyright National Electrical Manufacturers Association Pr

13、ovided by IHS under license with NEMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ANSI_IEC C78.62035-2004 Foreword (This foreword is not part of ANSI_IEC C78.62035-2004) Suggestions for improvement of this standard should be submitted to the Secretariat C78, Ame

14、rican National Standard Lighting Group (NEMA), 1300 North 17th Street, Suite 1847, Rosslyn, VA 22209. This standard was processed and approved by Accredited Standards Committee on Electric Lamps, C78, and its Sub-Committee, C78 WG 02. Committee approval of the standard does not necessarily imply tha

15、t all committee members voted for that approval. Information concerning approval of this standard is based on the documents listed in the table below. CDV RV 2ndEdition CDV C78(4)_4135 RV 78(4)_4136 David T. Mullen, Chairman, C78 David T. Mullen, Technical Coordinator Randolph N. Roy, Senior Editor

16、Matthew C. Clark, Coordinating Editor Copyright 2004 by American National Standard Lighting Group NEMA 3Copyright National Electrical Manufacturers Association Provided by IHS under license with NEMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ANSI_IEC C78.62035

17、-2004 Chapter I United States of Americas Deviations to IEC 62035 (2003-08) Ed. 1.1 Consolidated edition 1 Additions to Normative references Add the following to Clause 2, Normative references: ANSI_IEC C81.61-2003 Electrical lamp bases ANSI_IEC C81.62-2003 Lampholders for electrical lamps ANSI_IEC

18、C81.63-2004 Gauges for electric lamp bases and lampholders ANSI C78.40-1992 Specifications for mercury lamps ANSI C78.41-2001 Guidelines for low pressure sodium lamps ANSI C78.42-2001 High pressure sodium lamps ANSI C78.43-2004 Single-ended metal halide lamps ANSI C78.387-1995 Metal-halide lampsmeth

19、od of measuring characteristics ANSI C78.1381-1998 70-watt, M85 double-ended metal halide lamps ANSI C78.1385-1998 150-watt, M81 double-ended metal halide lamps ANSI C78.1386-1998 100-watt, M91 double-ended metal halide lamps ANSI C78.1387-2001 250-watt, M80 double-ended metal halide lamps ANSI C82.

20、4-2002 Ballasts for high intensity discharge and low pressure sodium lamps UL 1029-1994 High intensity discharge ballasts UL 1598-2000 Luminaires Alternate standards can be substituted for the corresponding IEC standard as listed here IEC 60061-1 ANSI C81.61 IEC 60061-2 ANSI C81.62 IEC 60061-3 ANSI

21、C81.63 IEC 60188 . ANSI C78.42 IEC 60192 . ANSI C78.40 IEC 60598-1 UL 1598 IEC 60662 . ANSI C78.41 IEC 60922 . UL 1029 IEC 60923 . ANSI C82.4 IEC 61167 . ANSI C78.43, C78.1381, C78.1385, C78.1386, C78.1387 Copyright 2004 by American National Standard Lighting Group NEMA 4Copyright National Electrica

22、l Manufacturers Association Provided by IHS under license with NEMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ANSI_IEC C78.62035-2004 2 Deviations to clause 5.1.1 Clause 5.1.1 does not apply. 3 Deviations to Table 1 In the line for subclause 5.2.2.3, in column

23、 3 replace “under consideration” with “Design” and in column 5 replace “under consideration” with “use ANSI C78.387.” 4 Deviations to Annex B In Annex B, Table B.2, the heating temperature for E26 and E39 bases shall be identical to, or greater than, the maximum base temperature given in the ANSI la

24、mp designation code for each lamp type. 5 Deviations to Annex E Annex E does not apply 6 Deviations to Annex F Part a of clause F.6 does not apply. Add the following note to clause F.6: Note: Lamps operated on lead circuits with a capacitor in series with the lamp or on electronic ballasts will oper

25、ate such that maximum lamp currents associated with rectification are restricted to values that will not be excessive for the system Copyright 2004 by American National Standard Lighting Group NEMA 5Copyright National Electrical Manufacturers Association Provided by IHS under license with NEMANot fo

26、r ResaleNo reproduction or networking permitted without license from IHS-,-,-ANSI_IEC C78.62035-2004 Copyright 2004 by American National Standard Lighting Group NEMA 6Chapter II IEC 62035 (2003-08) Ed. 1.1 Consolidated Edition Note: The consolidated edition consists of IEC 62035 (1999-10) plus IEC 6

27、2035-am1 (2003-06) The referenced IEC standard is not included in this document and must be obtained separately. IEC standards are available through the US National Committee of ANSI or IEC. This information is offered for your convenience. American National Standards Institute Attn: “eStandard Stor

28、e” 25 West 42ndStreet, 4thFloor New York, NY 10036 Or by calling 212 642-4900 during normal business hours. It may also be purchased electronically at the following URL www.ansi.org Or http:/webstore.ansi.org/ansidocstore/default.asp Copyright National Electrical Manufacturers Association Provided by IHS under license with NEMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-