ANSI EIA-948-2004 Component Tray for Automated Handling《自动搬运用组合托盘》.pdf

《ANSI EIA-948-2004 Component Tray for Automated Handling《自动搬运用组合托盘》.pdf》由会员分享，可在线阅读，更多相关《ANSI EIA-948-2004 Component Tray for Automated Handling《自动搬运用组合托盘》.pdf（48页珍藏版）》请在麦多课文档分享上搜索。

1、ANSVEIA-948-2004 Approved: August 9,2004 EIA STANDARD COMPONENT TRAY FOR AUTOMATED HANDLING EIA-948 August 2004 EA Electronic Components, Assemblies CI LL -I- 11 -H #$ x n I li! w I Y U u U U u U I 4.13 Bar code labeling (if required) shall be visible during normal operation. 4.14 Trays should be re

2、cyclable and permanently marked with visible recycling symbology. 4.15 The chamfered corner of the tray shall be used as the reference for component orientation. Copyright Electronic Components, Assemblies . Copyright Electronic Components, Assemblies I; III * DETAIL 2 I II I AT Copyright Electronic

3、 Components, Assemblies it can be always used for smaller sizes. So for example, if some manufacturer is supplying materials in all 4 tray sizes, it can keep only A-tray box and 2 different divider types in storage. The manufacturer is able to supply all shipments by using A-tray box and combination

4、s of dividers. 3.1 .I A-tray box Copyright Electronic Components, Assemblies & Materials Association Reproduced by IHS under license with ECA Not for ResaleNo reproduction or networking permitted without license from IHS-,-3.1.2 B-tray 3.1.2.1 B-tray box 3.1.2.2 B-tray stack in A-tray box Copyright

5、Electronic Components, Assemblies & Materials Association Reproduced by IHS under license with ECA Not for ResaleNo reproduction or networking permitted without license from IHS-,-3.1.3 C-tray 3.1.3.1 C-tray box 3.1.3.2 C-tray stack in A-tray box Copyright Electronic Components, Assemblies & Materia

6、ls Association Reproduced by IHS under license with ECA Not for ResaleNo reproduction or networking permitted without license from IHS-,-3.1.4 D-tray 3.1.4.1 D-tray box 3.1.4.2 D-tray stacks in A-tray box Copyright Electronic Components, Assemblies & Materials Association Reproduced by IHS under lic

7、ense with ECA Not for ResaleNo reproduction or networking permitted without license from IHS-,-3.1.4.3 D-tray stacks in B-tray box 3.1.4.4 D-tray stack in C-tray box Copyright Electronic Components, Assemblies & Materials Association Reproduced by IHS under license with ECA Not for ResaleNo reproduc

8、tion or networking permitted without license from IHS-,-3.2 Trays on pallet 1200x800 mm (so called Euro-pallet) 3.2.1 Tray stacks in boxes on pallet Tray boxes can be loaded to pallets directly and then wrapped with stretch or shrink film, or even placing collar around the stacks and then cover on t

9、op. It is possible also to use bigger container box, where the stacks are placed into. The modular tray sizes enable also that several different sizes of trays are loaded to trays with high packing density. It is recommended that D-trays are always packed to boxes, because the high stacks can be ver

10、y unstable and difficult to handle. The security issues must be taken into account, when choosing outer packaging method. 3.2.1 .I A-tray Copyright Electronic Components, Assemblies & Materials Association Reproduced by IHS under license with ECA Not for ResaleNo reproduction or networking permitted without license from IHS-,-Copyright Electronic Components, Assemblies & Materials Association Reproduced by IHS under license with ECA Not for ResaleNo reproduction or networking permitted without license from IHS-,-