ANSI CSA C22.2 NO.227.1-6-2006 Electrical Nonmetallic Tubing (Fourth Edition Update No 1 April 2007 Update No 2 December 2014).pdf

《ANSI CSA C22.2 NO.227.1-6-2006 Electrical Nonmetallic Tubing (Fourth Edition Update No 1 April 2007 Update No 2 December 2014).pdf》由会员分享，可在线阅读，更多相关《ANSI CSA C22.2 NO.227.1-6-2006 Electrical Nonmetallic Tubing (Fourth Edition Update No 1 April 2007 Update No 2 December 2014).pdf（58页珍藏版）》请在麦多课文档分享上搜索。

1、C22.2 No. 227.1-06(reaffirmed 2016)Electrical Nonmetallic TubingUpdate No. 2CAN/CSA-C22.2 No. 227.1-06December 2014Note: For information about the Standards Update Service or if you are missing any updates, go to shop.csa.ca or e-mail techsupportcsagroup.org.Title: Electrical nonmetallic tubing orig

2、inally published May 2006Revisions issued: Update No. 1 April 2007The following revisions have been formally approved and are marked by a vertical line in the margin on the attached replacement pages: Update your copy by inserting these revised pages.Keep the pages you remove for reference.Revised T

3、itle page, copyright page, Preface, Clauses 7.5.1.1, 9.1, and 9.2, and Tables 1, 2, and 3New Clause 7.5.1.2Deleted Foreword (CSA)CSA GroupCAN/CSA C22.2 No. 227.1-06Fourth EditionUnderwriters Laboratories Inc.UL 1653Second EditionElectrical Nonmetallic TubingMay 19, 2006(Title Page Reprinted: Decembe

4、r 23, 2014)ANSI/UL 1653-2014Approved byCommitment for AmendmentsThis standard is issued jointly by the Canadian Standards Association (operating as “CSA Group”) andUnderwriters Laboratories Inc. (UL). Comments or proposals for revisions on any part of the standardmay be submitted to CSA Group or UL

5、at any time. Revisions to this standard will be made only afterprocessing according to the standards development procedures of CSA Group and UL. CSA Group andUL will issue revisions to this standard by means of a revised or additional pages bearing their date ofissue.ISBN 1554360013 2006 CSA GroupAl

6、l rights reserved. No part of this publication may be reproduced in any form whatsoever without theprior permission of the publisher.This Standard is subject to review five years from the date of publication, and suggestions for itsimprovement will be referred to the appropriate committee. To submit

7、 a proposal for change, pleasesend the following information to inquirescsagroup.org and include “Proposal for change” in thesubject line: Standard designation (number); relevant clause, table, and/or figure number; wording ofthe proposed change; and rationale for the change.To purchase CSA Group St

8、andards and related publications, visit CSA Groups Online Store atwww.shop.csa.ca or call toll-free 1-800-463-6727 or 416-747-4044.Copyright 2014 Underwriters Laboratories Inc.ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standardshould be altered in any

9、way. All of ULs Standards and all copyrights, ownerships, and rights regardingthose Standards shall remain the sole and exclusive property of UL.This ANSI/UL Standard for Safety consists of the second edition including revisions through December23, 2014. The most recent designation of ANSI/UL 1653 a

10、s an American National Standard (ANSI)occurred on December 23, 2014. ANSI approval for a standard does not include the Cover Page,Transmittal Pages, Title Page (front and back), or the Preface.Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time.Proposal

11、s should be submitted via a Proposal Request in ULs On-Line Collaborative StandardsDevelopment System (CSDS) at http:/.To purchase UL Standards, visit Comm 2000 at http:/m- call toll-free 1-888-853-3503.PrefaceThis is the harmonized CSA Group and UL standard for Electrical Nonmetallic Tubing. It is

12、the fourthedition of CSA C22.2 No. 227.1 and the second edition of UL 1653. This edition of CSA C22.2 No. 227.1supersedes the previous edition published in 1997. This edition of UL 1653 supersedes the previousedition published in 1997. This harmonized standard has been jointly revised on December 23

13、, 2014. Forthis purpose, CSA Group and UL are issuing revision pages dated December 23, 2014.This harmonized standard was prepared by the CSA Group and Underwriters Laboratories Inc. (UL). Theefforts and support of the Technical Harmonization Committee 23A ENT Working Group of the Council onthe Harm

14、onization of Electrotechnical Standards of the Nations of the Americas (CANENA) are gratefullyacknowledged.This standard is considered suitable for use for conformity assessment within the stated scope of thestandard.This standard was reviewed by the CSA Subcommittee on Nonmetallic Conduit, Tubing,

15、and Fittings,under the jurisdiction of the CSA Technical Committee on Wiring Products and the CSA Strategic SteeringCommittee on Requirements for Electrical Safety, and has been formally approved by the CSA TechnicalCommittee.This standard has been approved as a National Standard of Canada by the St

16、andards Council of Canada(SCC).This standard has been approved by the American National Standards Institute (ANSI) as an AmericanNational Standard.Application of StandardWhere reference is made to a specific number of samples to be tested, the specified number shall beconsidered a minimum quantity.N

17、ote: Although the intended primary application of this standard is stated in its scope, it is important to note thatit remains the responsibility of the users of the standard to judge its suitability for their particular purpose.Level of harmonizationThis standard uses the IEC format but is not base

18、d on, nor shall it be considered equivalent to, an IECstandard. This standard is published as an equivalent standard for CSA Group and UL.An equivalent standard is a standard that is substantially the same in technical content, except as follows:Technical national differences are allowed for codes a

19、nd governmental regulations as well as thoserecognized as being in accordance with NAFTA Article 905, for example, because of fundamental climatic,geographical, technological, or infrastructural factors, scientific justification, or the level of protection thatthe country considers appropriate. Pres

20、entation is word for word except for editorial changes.Reasons for differences from IECThe Technical Harmonization Committee determined the safe use of electrical nonmetallic tubing andfittings is dependent on the design and performance of the raceway and cable systems with which theyare intended to

21、 be installed. Significant investigation is required to assess safety and system compatibilityissues that may lead to harmonization of traditional North American nonmetallic tubing and fittings withDECEMBER 23, 2014 CSA C22.2 NO. 227.1-06 UL 1653 5those presently addressed in the known IEC standards

22、. The THC agreed such future investigation mightbe facilitated by completion of harmonization of the North American standards for electrical nonmetallictubing and fittings.InterpretationsThe interpretation by the standards development organization of an identical or equivalent standard isbased on th

23、e literal text to determine compliance with the standard in accordance with the proceduralrules of the standards development organization. If more than one interpretation of the literal text has beenidentified, a revision is to be proposed as soon as possible to each of the standards developmentorga

24、nizations to more accurately reflect the intent.CSA Group Effective DateThe effective date for CSA Group will be announced through a CSA Informs or CSA Group CertificationNotice.UL Effective DateAs of December 23, 2014 all products Listed or Recognized by UL must comply with the requirements inthis

25、standard.A UL effective date is one established by Underwriters Laboratories Inc. and is not part of the ANSIapproved standard.DECEMBER 23, 2014CSA C22.2 NO. 227.1-06 UL 165366.2 Flame6.2.1 When subjected to the test in Clause 8.2, specimen plaques of the fitting material shall not burn formore than

26、 10 s. Flaming or glowing particles shall not fall from the specimen at any time during the test.This test need not be conducted on materials with a flame classification of 5 VA when evaluated inaccordance with UL 94 or CAN/CSA-C22.2 No. 0.17.6.3 Impact6.3.1 When subjected to the test in accordance

27、with Clause 8.3, the three samples of each trade sizeshall not show cracks, chips, or ruptures on the inside or outside when examined visually.6.4 Resistance to deflection split-type couplings6.4.1 Split-type couplings shall not show chips or cracks and shall remain secured to the ENT after beingsub

28、jected to the test in Clause 8.4.6.5 Concrete-tightness6.5.1 When a concrete-tight fitting is tested in accordance with Clause 8.5, there shall not be entrance ofconcrete aggregate into the fitting, outlet box, or ENT used in the test assembly. This test is not requiredif the smallest package of the

29、 fitting is marked in accordance with Clause 9.4(f).7 Test methods for ENT7.1 Conditioning7.1.1 Unless otherwise specified, all ENT shall be conditioned for not less than 24 h at 23 2C (73.43.6F) before being tested.7.2 Vertical flame (500 W burner)7.2.1 Using the test apparatus specified for the Ve

30、rtical Flame Test, Section 1060, in UL 1581 or for theVertical Test/FT1 (Nominal 500 W), Clause 4.11.1, in CSA C22.2 No. 0.3, the flame shall be applied fivetimes to three samples of each trade size, each approximately 450 mm (18 in) in length, for 15 s.MAY 19, 2006 CSA C22.2 NO. 227.1-06 UL 1653 13

31、7.3 Flame test in cable trays FT4 (Optional)7.3.1 Specimens of finished ENT shall be tested in accordance with the Vertical Flame Test (FT4) Conduit or Tubing on Cable Tray, in CSA C22.2 No. 211.0.Note: The FT4 flame test is a National Building Code of Canada requirement in designated applications i

32、n noncombustibleconstruction buildings.7.4 Bending7.4.1 A 750-mm (30-in) length of ENT of each size submitted shall be bent 90 around a mandrel with aradius as specified in Table 2.7.4.2 Distortion of the internal circular cross-section shall be determined by the free passage of a sphereor equivalen

33、t through the bore of the ENT. The diameter of the sphere shall be as specified in Table 3.In the case of a discrepancy, the sphere shall serve as the reference test method.7.5 Resistance to deflection7.5.1 General7.5.1.1 Six samples of each trade size shall be subjected to a load of 4448 N (1000 lb

34、f) for 16 (1/2) tradesize, 3470 N (780 lbf) for 21 (3/4) trade size, 3380 N (760 lbf) for 27 (1) trade size, and 1779 N (400 lbf)for 35 (1-1/4) through 53 (2) trade sizes. Each sample shall consist of a 150 3mm(61/8 in) length ofENT.7.5.1.2 In Canada, six samples of 63 (2-1/2) trade size shall be su

35、bjected to a load of 1334 N (300 lbf).Each sample shall consist of a 150 3mm(61/8 in) length of ENT.In the United States, this requirement does not apply.7.5.2 Apparatus7.5.2.1 The apparatus for this test shall consist of:a) an inside micrometer or telescopic gauges and a caliper; andb) a compressio

36、n machine having two steel platens at least 150 mm (6 in) long and 12.7 mm(1/2 in) thick, capable of running at a speed within the range of 10 15 mm/min (3/8 5/8in/min). The steel plates shall close together at a rate of 12.7 mm (1/2 in) per min.DECEMBER 23, 2014CSA C22.2 NO. 227.1-06 UL 165314f) th

37、e manufacturers code (date of manufacture);g) “For use in residential attics up to 900 mm (3 ft) above the bottom of the ceiling joist” whenthe ENT material complies with Clause 4.1.4; andh) in the United States, the manufacturing plant identification when the manufacturer has morethan one plant tha

38、t manufactures ENT.In Canada, Item (h) does not apply.i) in Canada, Trade Size 63 (2-1/2) shall be marked “For Canada Only”.9.2 The smallest package of cut lengths, coils, or reels of finished product shall be marked with:a) the manufacturers name, trademark, or other recognized symbol of identifica

39、tion;b) type ENT;c) the material used in construction, PVC;d) the metric designator and the trade size, for example 16 (1/2);e) the total length of product in the package;f) the manufacturers instructions for securing solvent-attached fittings (this marking may appearon the package or an accompanyin

40、g pamphlet); andg) “For use in residential attics up to 900 mm (3 ft) above the bottom of the ceiling joist” whenthe ENT material complies with Clause 4.1.4.h) in Canada, Trade Size 63 (2-1/2) shall be marked “ For Canada Only”.9.3 A fitting shall be legibly and durably marked with:a) the manufactur

41、ers name, trademark, or other recognized symbol of identification;b) the metric designator and the trade size, for example 16 (1/2); andc) in the United States, the manufacturing plant identification when the manufacturer has morethan one plant that manufactures ENT fittings.In Canada, Item (c) does

42、 not apply.9.4 The smallest package of fittings shall be marked with:a) the manufacturers name, trademark, or other recognized symbol of identification;b) the catalog number or equivalent designation;c) the metric designator and the trade size, for example 16 (1/2);d) the manufacturers code (date of

43、 manufacture);DECEMBER 23, 2014 CSA C22.2 NO. 227.1-06 UL 1653 21e) FOR CONCRETE ENCASEMENT, when the fittings comply with Clause 6.5;f) CONCRETE-TIGHT WHEN TAPED (optional); andg) identification of the specific ENT manufacturers that the fitting is intended for use with,unless it complies with Clau

44、se 6.1 when tested with all manufacturers ENT.DECEMBER 23, 2014CSA C22.2 NO. 227.1-06 UL 165322Table 1 ENT size and dimensions(See Clause 4.3.1 and Figure 1)Outside diameter (OD) Inside diameter (ID)Metric designator (tradesize)Minimum Maximum Minimum Maximummm (in) mm (in) mm (in) mm (in)16 (1/2) 2

45、1.13 (0.832) 21.54 (0.848) 14.58 (0.574) 16.00 (0.630)21 (3/4) 26.42 (1.040) 26.92 (1.060) 19.66 (0.774) 21.18 (0.834)27 (1) 33.15 (1.305) 33.66 (1.325) 25.37 (0.999) 26.90 (1.059)35 (1-1/4) 41.86 (1.648) 42.47 (1.672) 33.73 (1.328) 35.36 (1.392)41 (1-1/2) 47.96 (1.888) 48.56 (1.912) 39.57 (1.558) 4

46、1.20 (1.622)53 (2) 60.02 (2.363) 60.63 (2.387) 51.18 (2.015) 52.81 (2.079)63* 2-1/2* 72.45* (2.852)* 73.15* (2.880)* 61.7* (2.429)* 63.7* (2.508)*For Canada onlyTable 2 Mandrel sizes(See Clauses 7.4.1, 7.7.1, and 8.1.2.1)RadiusMetric designator (trade size) mm (in)16 (1/2) 87 (3.4)21 (3/4) 119 (4.7)

47、27 (1) 152 (6.0)35 (1-1/4) 204 (8.0)41 (1-1/2) 239 (9.4)53 (2) 305 (12.0)63* 2-1/2* 371* 14.6*For Canada onlyTable 3 Sphere sizes(See Clause 7.4.2)Sphere diameterMetric designator (trade size) mm (in)16 (1/2) 12.4 (0.49)21 (3/4) 16.8 (0.66)27 (1) 21.6 (0.85)35 (1-1/4) 28.9 (1.14)41 (1-1/2) 33.9 (1.3

48、3)53 (2) 43.6 (1.72)63* (2-1/2)* 52.3* (2.06)*For Canada onlyDECEMBER 23, 2014 CSA C22.2 NO. 227.1-06 UL 1653 23This is generated text for figtxt.Figure 1 ENT geometry(See Table 1)DECEMBER 23, 2014CSA C22.2 NO. 227.1-06 UL 165324Update No. 1C22.2 No. 227.1-06April 2007Note: General Instructions for

49、CSA Standards are now called Updates. Please contact CSA Information Products Sales or visit www.ShopCSA.ca for information about the CSA Standards Update Service.Title: Electrical Nonmetallic Tubing originally published May 2006The following revisions have been formally approved:Revised Outside front cover, inside front cover, and title pageNew National Standards of Canada textDeleted NoneCSA C22.2 No. 227.1-06 originally consisted of 26 pages, each dated May 20