ANSI CSA AM Z21.15B-2013 CSA 9.1B-2013 Standard for Manually Operated Gas Valves for Appliances Appliance Connector Valves and Hose End Valves (Addenda to the Second Edition).pdf

《ANSI CSA AM Z21.15B-2013 CSA 9.1B-2013 Standard for Manually Operated Gas Valves for Appliances Appliance Connector Valves and Hose End Valves (Addenda to the Second Edition).pdf》由会员分享，可在线阅读，更多相关《ANSI CSA AM Z21.15B-2013 CSA 9.1B-2013 Standard for Manually Operated Gas Valves for Appliances Appliance Connector Valves and Hose End Valves (Addenda to the Second Edition).pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、ANSI Z21.15b-2013CSA 9.1b-2013Addenda to the Second Edition ANSI Z21.15-2009 CSA 9.1-2009ANSI Z21.15a-2012 CSA 9.1a-2012Standard for Manually Operated Gas Valves for Appliances,Appliance Connector Valves and Hose End ValvesLegal Notice for StandardsCanadian Standards Association and CSA America, Inc

2、. (operating as “CSA Group”) develop standards through a consensusstandards development process approved by the Standards Council of Canada and American National Standards Institute. Thisprocess brings together volunteers representing varied viewpoints and interests to achieve consensus and develop

3、a standard.Although CSA Group administers the process and establishes rules to promote fairness in achieving consensus, it does notindependently test, evaluate, or verify the content of standards.Disclaimer and exclusion of liabilityThis document is provided without any representations, warranties,

4、or conditions of any kind, express or implied, including, withoutlimitation, implied warranties or conditions concerning this documents fitness for a particular purpose or use, its merchantability, orits non-infringement of any third partys intellectual property rights. CSA Group does not warrant th

5、e accuracy, completeness, orcurrency of any of the information published in this document. CSA Group makes no representations or warranties regarding thisdocuments compliance with any applicable statute, rule, or regulation. IN NO EVENT SHALL CSA GROUP, ITS VOLUNTEERS, MEMBERS, SUBSIDIARIES, OR AFFI

6、LIATED COMPANIES, OR THEIR EMPLOYEES,DIRECTORS, OR OFFICERS, BE LIABLE FOR ANY DIRECT, INDIRECT, OR INCIDENTAL DAMAGES, INJURY, LOSS, COSTS, OREXPENSES, HOWSOEVER CAUSED, INCLUDING BUT NOT LIMITED TO SPECIAL OR CONSEQUENTIAL DAMAGES, LOST REVENUE,BUSINESS INTERRUPTION, LOST OR DAMAGED DATA, OR ANY O

7、THER COMMERCIAL OR ECONOMIC LOSS, WHETHER BASED INCONTRACT, TORT (INCLUDING NEGLIGENCE), OR ANY OTHER THEORY OF LIABILITY, ARISING OUT OF OR RESULTING FROMACCESS TO OR POSSESSION OR USE OF THIS DOCUMENT, EVEN IF CSA GROUP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCHDAMAGES, INJURY, LOSS, COSTS, OR EX

8、PENSES.In publishing and making this document available, CSA Group is not undertaking to render professional or other services for or onbehalf of any person or entity or to perform any duty owed by any person or entity to another person or entity. The information inthis document is directed to those

9、 who have the appropriate degree of experience to use and apply its contents, and CSA Groupaccepts no responsibility whatsoever arising in any way from any and all use of or reliance on the information contained in thisdocument. CSA Group is a private not-for-profit company that publishes voluntary

10、standards and related documents. CSA Group has no power,nor does it undertake, to enforce compliance with the contents of the standards or other documents it publishes. Intellectual property rights and ownershipAs between CSA Group and the users of this document (whether it be in printed or electron

11、ic form), CSA Group is the owner, or theauthorized licensee, of all works contained herein that are protected by copyright, all trade-marks (except as otherwise noted to thecontrary), and all inventions and trade secrets that may be contained in this document, whether or not such inventions and trad

12、esecrets are protected by patents and applications for patents. Without limitation, the unauthorized use, modification, copying, ordisclosure of this document may violate laws that protect CSA Groups and/or others intellectual property and may give rise to aright in CSA Group and/or others to seek l

13、egal redress for such use, modification, copying, or disclosure. To the extent permitted bylicence or by law, CSA Group reserves all intellectual property rights in this document.Patent rightsAttention is drawn to the possibility that some of the elements of this standard may be the subject of paten

14、t rights. CSA Group shallnot be held responsible for identifying any or all such patent rights. Users of this standard are expressly advised that determination ofthe validity of any such patent rights is entirely their own responsibility.Authorized use of this documentThis document is being provided

15、 by CSA Group for informational and non-commercial use only. The user of this document isauthorized to do only the following:If this document is in electronic form:load this document onto a computer for the sole purpose of reviewing it;search and browse this document; andprint this document if it is

16、 in PDF format. Limited copies of this document in print or paper form may be distributed only to persons who are authorized by CSA Group to havesuch copies, and only if this Legal Notice appears on each such copy.In addition, users may not and may not permit others toalter this document in any way

17、or remove this Legal Notice from the attached standard;sell this document without authorization from CSA Group; ormake an electronic copy of this document.If you do not agree with any of the terms and conditions contained in this Legal Notice, you may not load or use this document ormake any copies

18、of the contents hereof, and if you do make such copies, you are required to destroy them immediately. Use of thisdocument constitutes your acceptance of the terms and conditions of this Legal Notice.1 Preface The standards set forth herein apply to the second edition of the Standard for Manually Ope

19、rated Gas Valves for Appliances, Appliance Connector Valves and Hose End Valves, ANSI Z21.15-2009 CSA 9.1-2009, and Addenda ANSI Z21.15a-2012 CSA 9.1a-2012, and supersede corresponding standards therein. Following their preparation by the supervising Technical Advisory Group, they were accepted by t

20、he American National Standards Institute (ANSI) and the Interprovincial Gas Advisory Council (IGAC), and subsequently approved. APPROVED IGAC February 23, 2012 March 4, 2013 March 19, 2013 American National Standards Institute, Inc. Interprovincial Advisory Council Effective in Canada November 1, 20

21、14 Standards Developer CSA AMERICA INC. CANADIAN STANDARDS ASSOCIATION 8501 East Pleasant Valley Road 5060 Spectrum Way, Suite 100 Cleveland, Ohio 44131 Mississauga, Ontario, Canada L4W 5N6 Published - March 2013 Copyright 2013 Canadian Standards Association Permission is granted to republish materi

22、al herein in laws or ordinances, and in regulations, administrative orders, or similar documents issued by public authorities. Those desiring permission for other republication should consult Canadian Standards Association, 5060 Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5N6. Copyrigh

23、t 2013 CSA America, Inc. Permission is granted to republish material herein in laws or ordinances, and in regulations, administrative orders, or similar documents issued by public authorities. Those desiring permission for other republication should consult CSA America, Inc., 8501 East Pleasant Vall

24、ey Road, Cleveland, Ohio 44131. 2 Addenda to American National Standard/CSA Standard For Manually Operated Gas Valves For Appliances, Appliance Connector Valves And Hose End Valves Part I: Construction 1.8 Strength 1.8.1 Bending Moment. A valve shall be capable of operation without cracking, breakin

25、g, or leaking while being subjected to a bending moment using the weight specified in Table III, Load For Bending Moment Test, in accordance with the following Method of Test. This test shall not apply to valves which have outlets threaded for orifice fittings. Method of Test This test shall be cond

26、ucted at room temperature. A new sample shall be subjected to the specified test. a. The inlet and outlet connections of the valve shall be assembled leak tight to the appropriate fittings as described below. The length of the inlet fitting shall be such that, after assembly, the dimension from the

27、valve inlet to the end of the inlet fitting will be 13 in (330 mm) 1/2 in (12.7 mm). The tightening torque for threaded pipe or tubing connections shall be one-half that shown in Table IV, Torques For Turning Effort Test. 1. Pipe threaded connections shall be assembled to Schedule 40 iron pipe, or p

28、ipe fitting, using non-Teflon type joint compound. 2. Tubing connections shall be assembled to steel tubing that conforms to the Standard for Welded and Cold Drawn Low Carbon Steel Tubing Annealed for Bending and Flaring, ANSI/SAE J525, or the Standard for Seamless Low-Carbon Steel Tubing Annealed f

29、or Bending and Flaring, ANSI/SAE J524, and has a minimum wall thickness of 0.028 in (0.71 mm), using the attachment means specified by the manufacturer. 1.8.3 Impact. This test applies only to individual manual valves not incorporated in devices that include other means to control main burner gas. 3

30、 a. All valves, except those listed in 1.8.3-b, shall be capable of withstanding the applicable impact specified in Table V, Impact, Foot Pounds (J), without cracking or breaking. Method of Test This test shall be conducted at room temperature. A new sample shall be subjected to the specified test.

31、A valve whose inlet is designed for connection to threaded pipe shall be supported by securing its inlet to a close pipe nipple of Schedule 80 iron pipe or a standard-weight pipe coupling mounted on a rigid surface so the free length of the nipple or coupling is not greater than 1 in (25.4 mm). The

32、valve shall be tightened to the support with a turning effort as specified in Table IV, Torques For Turning Effort Test. A valve whose inlet is designed for connection to semi-rigid tubing shall be mounted on a straight length of steel tubing conforming to the Standard for Welded and Cold Drawn Low

33、Carbon Steel Tubing Annealed for Bending and Flaring, ANSI/SAE J525, or the Standard for Seamless Low-Carbon Steel Tubing Annealed for Bending and Flaring, ANSI/SAE J524, and having a wall thickness of 0.035 in (0.889 mm). The tube fittings supplied with the valve or specified by the manufacturer sh

34、all be used, and the free length of the support tubing shall not exceed 1 in (25.4 mm). The outlet end of the valve shall have assembled to it a fitting of the type for which designed. The test device shall be arranged so the center line of contact between the striking weight and the valve will be 1

35、/4 in (6.4 mm) from the extreme outlet end of the valve. The valve shall then be struck four successive times at right angles to the longitudinal center line of the outlet gas way, with the valve being turned 90 degrees (1.57 rad) between each impact. After each impact, the valve shall be examined v

36、isually for cracks or breakage. A pendulum-type impact machine is shown in Figure 4, Pendulum-Type Impact Machine Used For Testing Gas Valves. b. The following shall withstand the applicable impact specified in Table VI without cracking or breaking: 1. Pilot adjustment and pilot shut-off valves and

37、pilot shut-off devices; 2. Valves with an outlet designed for an orifice fitting; 3. Valves with an inlet designed for connection to other than threaded pipe or tubing; and 4. Hose end valves. Method of Test This test shall be conducted at room temperature. A new sample shall be subjected to the spe

38、cified test. 4 The inlet of a completely assembled valve shall be suitably mounted on a rigid support. If the valve inlet is threaded for connection to iron pipe, it shall be mounted with a close pipe nipple of Schedule 80 pipe or a standard weight pipe coupling so the free length of the nipple or c

39、oupling is not greater than 1 in (25.4 mm). The valve shall be tightened to the support with the turning effort specified in Table IV, Torques For Turning Effort Test. A valve whose inlet is designed for connection to semi-rigid tubing shall be mounted on a straight length of steel tubing conforming

40、 to the Standard for Welded and Cold Drawn Low Carbon Steel Tubing Annealed for Bending and Flaring, ANSI/SAE J525, or the Standard for Seamless Low-Carbon Steel Tubing Annealed for Bending and Flaring, ANSI/SAE J524, and having a wall thickness of 0.035 in (.889 mm). Part III: Manufacturing and Production Tests. 3.2 The manufacturer shall test each device covered by this standard for: a. Leakage to the atmosphere; and b. Leakage through the valve. Each universal gas burner valve shall be tested for leakage when set to deliver each gas (i.e. Natural gas setting and Propane gas setting).