ANSI CSA AM CSA HGV 4.10-2012 Standard For Fittings for compressed hydrogen gas and hydrogen rich gas mixtures (First Edition).pdf

《ANSI CSA AM CSA HGV 4.10-2012 Standard For Fittings for compressed hydrogen gas and hydrogen rich gas mixtures (First Edition).pdf》由会员分享，可在线阅读，更多相关《ANSI CSA AM CSA HGV 4.10-2012 Standard For Fittings for compressed hydrogen gas and hydrogen rich gas mixtures (First Edition).pdf（27页珍藏版）》请在麦多课文档分享上搜索。

1、ANSI/CSA HGV 4.10-2012Standard ForFittings for compressed hydrogen gas and hydrogen rich gas mixturesLegal Notice for StandardsCanadian Standards Association and CSA America, Inc. (operating as “CSA Group”) develop standards through a consensusstandards development process approved by the Standards

2、Council of Canada. This process brings together volunteers representingvaried viewpoints and interests to achieve consensus and develop a standard. Although CSA Group administers the process andestablishes rules to promote fairness in achieving consensus, it does not independently test, evaluate, or

3、 verify the content ofstandards.Disclaimer and exclusion of liabilityThis document is provided without any representations, warranties, or conditions of any kind, express or implied, including, withoutlimitation, implied warranties or conditions concerning this documents fitness for a particular pur

4、pose or use, its merchantability, orits non-infringement of any third partys intellectual property rights. CSA Group does not warrant the accuracy, completeness, orcurrency of any of the information published in this document. CSA Group makes no representations or warranties regarding thisdocuments

5、compliance with any applicable statute, rule, or regulation. IN NO EVENT SHALL CSA GROUP, ITS VOLUNTEERS, MEMBERS, SUBSIDIARIES, OR AFFILIATED COMPANIES, OR THEIR EMPLOYEES,DIRECTORS, OR OFFICERS, BE LIABLE FOR ANY DIRECT, INDIRECT, OR INCIDENTAL DAMAGES, INJURY, LOSS, COSTS, OREXPENSES, HOWSOEVER C

6、AUSED, INCLUDING BUT NOT LIMITED TO SPECIAL OR CONSEQUENTIAL DAMAGES, LOST REVENUE,BUSINESS INTERRUPTION, LOST OR DAMAGED DATA, OR ANY OTHER COMMERCIAL OR ECONOMIC LOSS, WHETHER BASED INCONTRACT, TORT (INCLUDING NEGLIGENCE), OR ANY OTHER THEORY OF LIABILITY, ARISING OUT OF OR RESULTING FROMACCESS TO

7、 OR POSSESSION OR USE OF THIS DOCUMENT, EVEN IF CSA GROUP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCHDAMAGES, INJURY, LOSS, COSTS, OR EXPENSES.In publishing and making this document available, CSA Group is not undertaking to render professional or other services for or onbehalf of any person or enti

8、ty or to perform any duty owed by any person or entity to another person or entity. The information inthis document is directed to those who have the appropriate degree of experience to use and apply its contents, and CSA Groupaccepts no responsibility whatsoever arising in any way from any and all

9、use of or reliance on the information contained in thisdocument. CSA Group is a private not-for-profit company that publishes voluntary standards and related documents. CSA Group has no power,nor does it undertake, to enforce compliance with the contents of the standards or other documents it publis

10、hes. Intellectual property rights and ownershipAs between CSA Group and the users of this document (whether it be in printed or electronic form), CSA Group is the owner, or theauthorized licensee, of all works contained herein that are protected by copyright, all trade-marks (except as otherwise not

11、ed to thecontrary), and all inventions and trade secrets that may be contained in this document, whether or not such inventions and tradesecrets are protected by patents and applications for patents. Without limitation, the unauthorized use, modification, copying, ordisclosure of this document may v

12、iolate laws that protect CSA Groups and/or others intellectual property and may give rise to aright in CSA Group and/or others to seek legal redress for such use, modification, copying, or disclosure. To the extent permitted bylicence or by law, CSA Group reserves all intellectual property rights in

13、 this document.Patent rightsAttention is drawn to the possibility that some of the elements of this standard may be the subject of patent rights. CSA Group shallnot be held responsible for identifying any or all such patent rights. Users of this standard are expressly advised that determination ofth

14、e validity of any such patent rights is entirely their own responsibility.Authorized use of this documentThis document is being provided by CSA Group for informational and non-commercial use only. The user of this document isauthorized to do only the following:If this document is in electronic form:

15、load this document onto a computer for the sole purpose of reviewing it;search and browse this document; andprint this document if it is in PDF format. Limited copies of this document in print or paper form may be distributed only to persons who are authorized by CSA Group to havesuch copies, and on

16、ly if this Legal Notice appears on each such copy.In addition, users may not and may not permit others toalter this document in any way or remove this Legal Notice from the attached standard;sell this document without authorization from CSA Group; ormake an electronic copy of this document.If you do

17、 not agree with any of the terms and conditions contained in this Legal Notice, you may not load or use this document ormake any copies of the contents hereof, and if you do make such copies, you are required to destroy them immediately. Use of thisdocument constitutes your acceptance of the terms a

18、nd conditions of this Legal Notice.PrefaceThis publication represents a standard for safe operation, substantial and durable construction and performance testing of fittings used with compressed hydrogen gas and hydrogen rich gas mixtures, within limitations given below and in the scope of this stan

19、dard.This standard is based on engineering principles, research and the combined expertise of manufacturers, users, and others having specialized experience.Nothing in this standard is to be considered in any way as indicating a measure of quality beyond compliance with the provisions it contains. I

20、t is designed to allow compliance of products which may exceed that specified in the provisions herein. In its preparation, full recognition has been given to possibilities of improvement through ingenuity of design. This standard is subject to revision as further experience and investigation may sh

21、ow it is necessary and desirable.CSA Group, does not assume or undertake to discharge any responsibility of the manufacturer or any other party. CSA Group shall not incur any obligation or liability for damages, including consequential damages, arising out of or in connection with the use, interpret

22、ation of or reliance upon this standard.Users of this American National Standard are advised that the devices, products, and activities within its scope may be subject to regulation at the federal, state, or local levels. Users are strongly urged to investigate this possibility through appropriate c

23、hannels. In the event of a conflict with this standard, the federal, state, or local regulations should be followed.CAUTION NOTICE: This American National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute, Inc., require that action be taken

24、 to reaffirm, revise or withdraw this standard no later than five (5) years from the date of approval. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute, Inc., 25 West 43rd Street, Fourth Floor,

25、New York, N.Y. 10036, (212) 642-4900.EFFECTIVE DATE: An organization using this standard for product evaluation as a part of its certification program will normally establish the date by which all products certified by that organization should comply with this standard.History Of Development Of ANSI

26、/CSA HGV 4.10 (This history is informative and is not part of the standard.)NOTE: This is the first edition of ANSI HGV 4.10.In September 2002, CSA met with the U.S. Department of Energy, Renewable Fuels Group in Washington, D.C. to discuss standards development opportunities in the hydrogen technol

27、ogy area. During this meeting, DOE requested that CSA provide a proposal relating to the development of hydrogen technology standards and codes in the United States. Industry recognized that an important consideration in the successful commercialization of hydrogen gas as a vehicle fuel was the issu

28、e of codes and standards, pertaining to both fueling stations and vehicle fuel system components. CSA undertook the goal of establishing a program for the development of an organized family of coordinated standards that addresses hydrogen gas vehicles and fueling stations.Industry and CSA recognized

29、 there was no standard that addressed safety requirements for hydrogen fittings. The development of such a standard was necessary based on industry needs and feedback: (1) Conventional fitting technology used in 350 bar hydrogen applications may have technical issues when used in long term applicati

30、ons at the 700 bar level. (2) There were no standards available for piping systems for hydrogen applications at the 700 bar pressure levels. (3) Automotive OEMs driving the application of hydrogen as a fuel for vehicles expressed concern over solutions in demonstration projects in the field. The foc

31、us of the new fittings standard established performance based safety requirements for the material, design, manufacture and testing of fittings and stud ends for use with compressed gaseous hydrogen. CSA has positioned itself as a leader in the fuel cell, hydrogen and natural gas sectors as a Standa

32、rds Developing Organization (SDO). CSA is aggressively updating and developing national standards, and is playing a major role in the promulgation of US technologies nationally. As US TAG Administrator to IEC TC 105 for Fuel Cell Technologies and as US TAG members of ISO TC 197 and ISO TC 22 / SC 25

33、, CSA is facilitating US technology internationally. CSA organized committees to address technical issues in the development of standards which would affect future expansion of the hydrogen industry.The HGV 4.10 hydrogen fittings standard was processed as an American National Standard in accordance

34、with procedures of the American National Standards Institute (ANSI).This is the first edition of the HGV 4.10 hydrogen fittings standard, and was approved by the American National Standards Institute, Inc. on April 26, 2012.Previous editions of this standard are as follows:CSA America HGV 4.10-2008

35、TIRTechnical Advisory Group on Standards For Performance of Fittings For Compressed Hydrogen Gas And Hydrogen Rich Gas Mixtures William Collins UTC Power ChairmanRobert Boyd Boyd Hydrogen LLCRonald Czischke Underwriters Laboratories IncMark McDougall Powertech Labs Inc.Phil Robinson Parker HannifinM

36、ike Spears SSP FittingsMike Steele General Motors Corp.Joint Automotive Technical Committee Livio Gambone Powertech Labs Inc. ChairmanJoe Cohen Air Products and Chemicals Inc.Douglas Horne Clean Vehicle Education FoundationJohn Jordan Agility Fuel SystemsSusana Katz S. Katz and Associates Inc.Norman

37、 Newhouse Lincoln Composites, Inc.Gini Sage General Motors of Canada LimitedStan Sinclair Southern California Gas CompanyNeel Sirosh Quantum Fuel Systems Technologies Worldwide, Inc.Mike Spears SSP Fittings CorporationRhoads Stephenson Motor Vehicle Fire Research InstituteANSI/CSA HGV 4.10-2012Fitti

38、ngs for compressed hydrogen gas and hydrogen rich gas mixturesA trade-mark of the Canadian Standards Association, operating as “CSA Group”Published in May 2012 by CSA GroupA not-for-profit private sector organization5060 Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5N61-800-463-6727 416

39、-747-4044Visit our Online Store at shop.csa.caTo purchase standards and related publications, visit our Online Store at shop.csa.ca or call toll-free 1-800-463-6727 or 416-747-4044.ISBN 978-1-55491-982-6 2012 CSA GroupAll rights reserved. No part of this publication may be reproduced in any form wha

40、tsoever without the prior permission of the publisher.1ContentsPageMay 2012 2012 CSA GroupPart I Construction 1.1 Scope .21.2 General .31.3 Instructions .31.4 Marking 3Part II Performance 2.1 General .52.2 Design Qualification or Type Tests 62.3 External Leak Test .62.4 Hydrostatic Burst Test .72.5

41、Hydraulic Cyclic Endurance Test 72.6 Gas Cyclic Endurance Test 82.7 Rotary Flex Test .92.8 Explosive Decompression 92.9 Make and Break Test .102.10 Thermal Shock 11Table I Hydraulic Cyclic Endurance Test Requirements 12Part III Manufacturing And Production Test .133.1 .133.2 .133.3 .133.4 .133.5 .13

42、Part IV Definitions 14EXHIBIT A Normative References .15APPENDIX A Additional Standards and References .19NOTEThis standard contains SI (Metric) equivalents to the yard/pound quantities, the purpose being to allow the standard to be used in SI (Metric) units. (Standard for use of the International S

43、ystem of Units (SI): The Modern Metric System, IEEE/ASTM SI I0 or Metric Practice Guide, CAN/CSA Z234.1 are used as a guide in making metric conversion from yard/pound quantities.) If a value for a measurement and an equivalent value in other units, the first stated is to be regarded as the requirem

44、ent. The given equivalent value may be approximate. If a value for a measurement and an equivalent value in other units, are both specified as a quoted marking requirement, the first stated unit, or both shall be provided.2May 2012ANSI/CSA HGV 4.10-2012 2012 CSA GroupANSI/CSA HGV 4.10-2012Performanc

45、e Of Fittings For Compressed Hydrogen Gas And Hydrogen Rich Gas Mixtures Part I: Construction1.1 Scope This standard specifies uniform methods for testing and evaluating the performance of fittings for use with compressed hydrogen gas and hydrogen rich gas mixtures. It does not address special requi

46、rements for liquid and slush hydrogen. This standard applies to hydrogen systems applications to meet current market needs. In this standard, the term “fittings” includes fittings, connectors, and stud ends for ports. This standard does not apply to stand alone components, such as:1. Quick Action co

47、uplings, (i.e., quick connects);2. Flanges; or3. Welded joints.This standard applies to newly manufactured fittings. It does not apply to fittings qualified for hydrogen service by other relevant Nationally Recognized standards or regulations such as AFNOR, BSI, CGA, JIS, etc. If the value for measu

48、rement as given in this standard is followed by an equivalent value in other units, the first stated value is to be regarded as the specification.All references to pressure throughout this standard are to be considered gauge pressures, unless otherwise specified.2The requirements of this standard ma

49、y be superseded by an application specific standard.The construction of parts not covered by this standard shall be in accordance with reasonable concepts of safety, substantiality and durability.All specifications as to construction set forth herein may be satisfied by the construction actually prescribed or such other construction as will provide at least equivalent performance.3May 2012Standard for fittings for compressed hydrogen 2012 CSA Group gas and hydrogen rich gas mixtures1.2 General1.2.1 Material Requirements.Materials normally in hydrogen contact shall be demonstrated