ANSI CAN CSA-C22.2 NO.60745-2-15-10-2010 Hand-held motor operated electric tools - Safety - Part 2-15 Particular requirements for hedge trimmers (First Edition Update No 1 Septembe.pdf

《ANSI CAN CSA-C22.2 NO.60745-2-15-10-2010 Hand-held motor operated electric tools - Safety - Part 2-15 Particular requirements for hedge trimmers (First Edition Update No 1 Septembe.pdf》由会员分享，可在线阅读，更多相关《ANSI CAN CSA-C22.2 NO.60745-2-15-10-2010 Hand-held motor operated electric tools - Safety - Part 2-15 Particular requirements for hedge trimmers (First Edition Update No 1 Septembe.pdf（140页珍藏版）》请在麦多课文档分享上搜索。

1、Hand-held motor operated electric tools Safety Part 2-15: Particular requirements for hedge trimmersCAN/CSA-C22.2 No. 60745-2-15-10(IEC 60745-2-15:2006+A1:2009, MOD)National Standard of CanadaNOT FOR RESALE.PUBLICATION NON DESTINE LA REVENTE.Legal Notice for StandardsCanadian Standards Association (

2、CSA) standards are developed through a consensus standards development process approved by the Standards Council of Canada. This process brings together volunteers representing varied viewpoints and interests to achieve consensus and develop a standard. Although CSA administers the process and estab

3、lishes rules to promote fairness in achieving consensus, it does not independently test, evaluate, or verify the content of standards.Disclaimer and exclusion of liabilityThis document is provided without any representations, warranties, or conditions of any kind, express or implied, including, with

4、out limitation, implied warranties or conditions concerning this documents fitness for a particular purpose or use, its merchantability, or its non-infringement of any third partys intellectual property rights. CSA does not warrant the accuracy, completeness, or currency of any of the information pu

5、blished in this document. CSA makes no representations or warranties regarding this documents compliance with any applicable statute, rule, or regulation. IN NO EVENT SHALL CSA, ITS VOLUNTEERS, MEMBERS, SUBSIDIARIES, OR AFFILIATED COMPANIES, OR THEIR EMPLOYEES, DIRECTORS, OR OFFICERS, BE LIABLE FOR

6、ANY DIRECT, INDIRECT, OR INCIDENTAL DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES, HOWSOEVER CAUSED, INCLUDING BUT NOT LIMITED TO SPECIAL OR CONSEQUENTIAL DAMAGES, LOST REVENUE, BUSINESS INTERRUPTION, LOST OR DAMAGED DATA, OR ANY OTHER COMMERCIAL OR ECONOMIC LOSS, WHETHER BASED IN CONTRACT, TORT (INCLUD

7、ING NEGLIGENCE), OR ANY OTHER THEORY OF LIABILITY, ARISING OUT OF OR RESULTING FROM ACCESS TO OR POSSESSION OR USE OF THIS DOCUMENT, EVEN IF CSA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES.In publishing and making this document available, CSA is not undertak

8、ing to render professional or other services for or on behalf of any person or entity or to perform any duty owed by any person or entity to another person or entity. The information in this document is directed to those who have the appropriate degree of experience to use and apply its contents, an

9、d CSA accepts no responsibility whatsoever arising in any way from any and all use of or reliance on the information contained in this document. CSA is a private not-for-profit company that publishes voluntary standards and related documents. CSA has no power, nor does it undertake, to enforce compl

10、iance with the contents of the standards or other documents it publishes. Intellectual property rights and ownershipAs between CSA and the users of this document (whether it be in printed or electronic form), CSA is the owner, or the authorized licensee, of all works contained herein that are protec

11、ted by copyright, all trade-marks (except as otherwise noted to the contrary), and all inventions and trade secrets that may be contained in this document, whether or not such inventions and trade secrets are protected by patents and applications for patents. Without limitation, the unauthorized use

12、, modification, copying, or disclosure of this document may violate laws that protect CSAs and/or others intellectual property and may give rise to a right in CSA and/or others to seek legal redress for such use, modification, copying, or disclosure. To the extent permitted by licence or by law, CSA

13、 reserves all intellectual property rights in this document.Patent rightsAttention is drawn to the possibility that some of the elements of this standard may be the subject of patent rights. CSA shall not be held responsible for identifying any or all such patent rights. Users of this standard are e

14、xpressly advised that determination of the validity of any such patent rights is entirely their own responsibility.Authorized use of this documentThis document is being provided by CSA for informational and non-commercial use only. The user of this document is authorized to do only the following:If

15、this document is in electronic form:.load this document onto a computer for the sole purpose of reviewing it;.search and browse this document; and.print this document if it is in PDF format. Limited copies of this document in print or paper form may be distributed only to persons who are authorized

16、by CSA to have such copies, and only if this Legal Notice appears on each such copy.In addition, users may not and may not permit others to.alter this document in any way or remove this Legal Notice from the attached standard;.sell this document without authorization from CSA; or.make an electronic

17、copy of this document.If you do not agree with any of the terms and conditions contained in this Legal Notice, you may not load or use this document or make any copies of the contents hereof, and if you do make such copies, you are required to destroy them immediately. Use of this document constitut

18、es your acceptance of the terms and conditions of this Legal Notice.Update No. 4CAN/CSA-C22.2 No. 60745-2-15-10April 2017Note: For information about the Standards Update Service or if you are missing any updates, go to shop.csa.ca or e-mail techsupportcsagroup.org.Title: Hand-held motor operated ele

19、ctric tools Safety Part 2-15: Particular requirements for hedge trimmers originally published June 2010Revisions issued: Update No. 1 September 2011Update No. 2 September 2013Update No. 3 March 2016The following revisions have been formally approved and are marked by a vertical line in the margin on

20、 the attached replacement pages:Revised Title page, copyright page, Contents, Preface, Clause 19.103DV, Table 101DV, and Figure 108DVNew Figures 108DV (a) and 108DV (b)Deleted NoneUpdate your copy by inserting these revised pages.Keep the pages you remove for reference.Blank pageCSAGroupCAN/CSA-C22.

21、2No.60745-2-15-10FirstEdition(IEC60745-2-15:2006+A1:2009,MOD)UnderwritersLaboratoriesInc.UL60745-2-15FirstEditionHand-Held Motor-Operated Electric Tools Safety Part 2-15:ParticularRequirementsforHedgeTrimmersJune 28, 2010(Title Page Reprinted: April 28, 2017)This national standard is based on public

22、ation IEC 60745-2-15, Edition 2.1 (Edition 2:2006 consolidatedwith Amendment 1:2009).ANSI/UL60745-2-15-2017Approved byCommitmentforAmendmentsThis Standard is issued jointly by CSA Group (CSA) and Underwriters Laboratories Inc. (UL).Comments or proposals for revisions on any part of the standard may

23、be submitted to CSA or UL atany time. Revisions to this Standard will be made only after processing according to the standardsdevelopment procedures of CSA and UL. CSA and UL will issue revisions to this Standard by meansof a new edition or revised or additional pages bearing their date of issue.ISB

24、N978-1-55491-386-22010CSAGroupAll rights reserved. No part of this publication may be reproduced in any form whatsoever without theprior permission of the publisher.This Standard is subject to review within five years from the date of publication, and suggestions for itsimprovement will be referred

25、to the appropriate committee. To submit a proposal for change, pleasesend the following information to inquirescsagroup.org and include Proposal for change in thesubject line: Standard designation (number); relevant clause, table, and/or figure number; wording ofthe proposed change; and rationale fo

26、r the change.To purchase CSA Group Standards and related publications, visit CSA Groups Online Store atshop.csa.ca or call toll-free 1-800-463-6727 or 416-747-4044.Copyright2017UnderwritersLaboratoriesInc.ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Stan

27、dardshould be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regardingthose Standards shall remain the sole and exclusive property of UL.This ANSI/UL Standard for Safety consists of the First Edition including revisions through April 28,2017.The most recent desig

28、nation of ANSI/UL 60745-2-15 as an American National Standard (ANSI)occurred on April 28, 2017. ANSI approval for a standard does not include the Cover Page, TransmittalPages, Title Page (front and back), or the Preface. The National Difference Page and IEC Forewordare also excluded from the ANSI ap

29、proval of IEC-based standards.Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time.Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative StandardsDevelopment System (CSDS) at https:/.To purchase UL Standards, visit Comm 2000 a

30、t http:/m- or calltoll-free 1-888-853-3503.CONTENTSPREFACE 5NATIONALDIFFERENCES .7FOREWORD 81 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 Normative references . . . . . . . . . .

31、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 Terms and definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114 General requirements . . . . . . .

32、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125 General conditions for the tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126 Void . . . . . . . . . . . . . . .

33、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127 Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 Mark

34、ing and instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12A9 Protection against access to live parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14A10 Starting . .

35、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14A11 Input and current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

36、4A12 Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14A13 Leakage current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

37、. . . . . . . .14A14 Moisture resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14A15 Electric strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

38、. . . . . . . . . . . . .14A16 Overload protection of transformers and associated circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . .14B17 Endurance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

39、. . .14B18 Abnormal operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14B19 Mechanical hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40、. . .14B19.101 Handles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14B19.102 Hand protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .191

41、9.103 Cutting device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2019.104 Blade stopping time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20C19.105 Lower barr

42、ier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2319.106 Cutting device cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2420 Mechanical strength . . . .

43、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2421 Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24A22 Internal wiring

44、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2523 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .262

45、4 Supply connections and external flexible cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2625 Terminals for external conductors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2726 Provision for earthin

46、g . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2727 Screws and connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2728 Creepage distance

47、s, clearances and distances through insulation . . . . . . . . . . . . . . . . . . . . . . . .2729 Resistance to heat, fire and tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2730 Resistance to rusting . . . . . . . . . . . . . . . . . . .

48、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2731 Radiation, toxicity and similar hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27APRIL28,2017 CAN/CSA-C22.2NO.60745-2-15-10 UL60745-2-15 3AnnexesAn

49、nexK(normative)BatterytoolsandbatterypacksAnnex L (normative) Battery tools and battery packs provided with mains connection ornon-isolatedsourcesAnnexAA(normative)SymbolsforsafetyrecommendationsandwarningsBibliographyJUNE28,2010CAN/CSA-C22.2NO.60745-2-15-10 UL60745-2-154PREFACEThis is the harmonized CSA Group and UL Standard for Hand-Held Motor-Operated Electric Tools Safety Part 2-15: Particular Requirements For Hedge Trimmers. It is the first edition of CAN/CSA-C22.2No. 60745-2-15, and the first edition