ANSI BHMA A156.20-2017 STRAP AND TEE HINGES AND HASPS.pdf

《ANSI BHMA A156.20-2017 STRAP AND TEE HINGES AND HASPS.pdf》由会员分享，可在线阅读，更多相关《ANSI BHMA A156.20-2017 STRAP AND TEE HINGES AND HASPS.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 1 ANSI/BHMA A156.20-2017 Revision of ANSI/BHMA A156.20-2012 STANDARD FOR STRAP AND TEE HINGES, AND HASPS SPONSOR BUILDERS HARDWARE MANUFACTURERS ASSOCIATION, INC. Approved by the AMERICAN NATIONAL STANDARDS INSTITUTE December 22, 2017 2 AMERICAN NATIONAL STANDARD An American National Standard impli

2、es a consensus of those substantially concerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether he has ap

3、proved the Standard or not, from manufacturing, marketing, purchasing or using products, processes, or procedures not conforming to the Standard. American National Standards are subject to periodic review and users are cautioned to obtain the latest editions. CAUTION NOTICE: This American National S

4、tandard may be revised or withdrawn at any time. The procedures of the American National Standards Institute require that action be taken to reaffirm, revise, or withdraw this Standard no later than five years from the date of publication. Publishers of American National Standards may receive curren

5、t information on all Standards by calling or writing the American National Standards Institute. Published by BUILDERS HARDWARE MANUFACTURERS ASSOCIATION, INC. 355 Lexington Avenue New York, New York 10017 Copyright 2017 by the Builders Hardware Manufacturers Association, Inc. Not to be reproduced w

6、ithout specific authorization from BHMA Printed in the USA This Standard was approved by ANSI under the Canvass Method. The Builders Hardware Manufacturers Association, Inc. was accredited on 21 March 1983 by ANSI as a sponsor using the canvass method.3 FOREWORD (This Foreword is not a part of ANSI/

7、BHMA A156.20) The general classification of builders hardware includes a wide variety of items which are divided into several categories. To recognize this diversity, a sectional classification system has been established. Strap and Tee Hinges, and Hasps is one such section and this Standard is the

8、result of the collective efforts of members of the Builders Hardware Manufacturers Association, Inc. who manufacture this product. The total Product Standards effort is, therefore, a collection of sections, each covering a specific category of items. The BHMA recognizes that errors will be found, it

9、ems will become obsolete, and new products, methods and materials will be developed. With this in mind, the Association plans to update, correct and revise these Standards on a regular basis. In most cases, products have been described in grade levels related to their durability. Grade classificatio

10、ns indicate levels only within their own product categories. Choice of grade and specific product are made on the basis of utility, aesthetics, security objectives and end use desired. The BHMA numbers which indicate types and functions of hardware do not identify size or finish and are not intended

11、 to be used without necessary supplementary information. Individual manufacturers catalogs are consulted. 4 TABLE OF CONTENTS 1. SCOPE. 5 2. DEFINITIONS. 5 3. GENERAL. 5 TABLE I TEST VALUES FOR STRAP AND TEE HINGES 6 4. HINGE CYCLE TEST 6 5. HINGE PERMANENT SET TEST PROCEDURE the qualifying lateral

12、measurement is the average of these two. 4.2 Cycle Test Cycle the hinges through 90 degrees for 100,000 cycles At the conclusion of the cycle testing, each specimen shall again be measured as in 4.1 to determine the displacement between leaves and knuckles. Wear is determined as the difference betwe

13、en final and initial measurements. Record measurements of wear for all hinges. The measurements of the greatest wear shall be compared to the permissible figures. The hinges passing the test shall comply with the vertical and lateral wear requirements below: 7 4.3 Requirements Cycle Test Requirement

14、s Vertical and Lateral Wear Allowable Maximum Bearing Grade 1 Grade 1 Grade 2 .010 inches (.25 mm) .020 inches (.5mm) .030 inches (.75 mm) 5. HINGE PERMANENT SET TEST PROCEDURE & REQUIREMENT 5.1 Lateral shift. The lateral shift of doors away from jamb shall not exceed .060 in (1.5 mm) when tested in

15、 the following manner. 5.2 Door position. Measure the horizontal position of the door at the top hinge, using the dial indicator, with the door in the closed position. 5.3 Add test weight. Add the test weight, as indicated in the chart for the hinge, at the outer edge of the door. 5.4 Open and close

16、 door. Open the door to the 90 degree open position and return to the closed position. 5.5 Remove the test weight. 5.6 Re-measure door position. Measure the horizontal position of the door as in 5.2. The difference between the two measurements is the horizontal set of the door (or lateral shift). 6.

17、 STRENGTH TEST FOR HASPS 6.1 Mounting. The hasp shall be mounted in the closed position on a steel plate using machine screws of a size equivalent to the fasteners provided with the hasp. The hasp, except key locking type, shall be fastened with a padlock having a shackle with a nominal diameter of

18、0.250 in (6.4 mm). 6.2 Fixed or Adjustable Staple Torque Resistance 6.2.1 A torque measuring device shall be applied to the staple in a plane parallel to the mounting surface. The torque shall be applied gradually using a nominal 0.375 in (9.5 mm) diameter hardened steel rod and sustained for a peri

19、od of 30 seconds. If staple opening does not accommodate both padlock hasp and torque rod, torque shall be applied by inserting torque rod through locked padlock shackle throat. Grade 1 Grade 2 Grade 3 3000 lbf-in (339 Nm) 480 lbf-in ( 54 Nm) 125 lbf-in (14Nm) 6.2.2 After application of the required

20、 torque, the padlock shall continue to be secured to the staple and the staple to the hasp leaf preventing disengagement of the hasp. 6.3 Fixed, Adjustable, Swivel Staple, Staple Rotating Post, or Latching Post Pull Resistance 6.3.1 A load dynamometer shall be applied to load the staple or post perp

21、endicular to the mounting surface. The force shall be applied gradually and be sustained for a period of 30 seconds. Grade 1 250 lbf (1112 N) 6.3.2 After the application of the required load, the hasp shall still be functional. 7. PERFORMANCE REQUIREMENTS FOR FINISHES 7.1 Application. This test appl

22、ies to all products treated by plating or painting. 7.2 Salt Spray Test. This test shall be conducted in accordance with ANSI/BHMA A156.18-2016 for Materials and Finishes. Finishes shall withstand exposure for 24 hours. 8 8. EXPLANATION OF NUMBERING SYSTEM 8.1 The first letter denotes the BHMA Produ

23、ct Section (A). 8.2 The first numeral indicates the general type of material used. 0. Optional Material 8. Wrought Steel 8.3 The second numeral identifies the product category. 1. Strap Hinge 2. Tee Hinge 3. Hasp 4. Pintel 8.4 The third numeral identifies the type of material surface. 1. Not Treated

24、 2. Treated by Plating 3. Treated by Painting 8.5 The fourth numeral identifies the function or description of the item or both. 0. Aluminum Hinge Pin 1. Steel Hinge Pin 2. Brass Hinge Pin (only on products with finish BHMA 603) 3. Adjustable Staple 4. Fixed Staple or Rotating Post 5. Swivel Staple

25、or Latching Post 6. Open Hinged - Fixed Staple 7. Double Hinged - Fixed Staple 8. Heavy Open Hinged - Fixed Staple 9. Key-locking 8.6 The fifth numeral designates the grade classification of the item. 1. Grade 1 or Grade 1 Bearing Type 2. Grade 2 3. Grade 3 9 9. FUNCTIONS AND IDENTIFYING NUMBERS All

26、 illustrations and type numbers are typical. See individual manufacturers catalogs for details. Hinges (see 4 and 5 for required tests) 9.1 Strap Hinges Illustrations Not treated Steel Pin A81111 A81112 Not Treated Aluminum Pin A81101 A81102 Plated Steel Pin A01211 A01212 A81211 A81212 Plated Alumin

27、um Pin A01201 A01202 A81201 A81202 Plated Brass Pin A01221 A01222 A81221 A81222 Painted Steel Pin A81311 A81312 Painted Aluminum Pin A81301 A81302 9.2.1 Tee Hinges Not Treated Steel Pin A82111 A82112 Not Treated Aluminum Pin A82101 A82102 Plated Steel Pin A02211 A02212 A82211 A82212 Plated Aluminum

28、Pin A02201 A02202 A82201 A82202 Plated Brass Pin A02221 A02222 A82221 A82222 Painted Steel Pin A82311 A82312 Painted Aluminum Pin A82301 A82302 9.2.2 Pintle Tee Hinge Not Treated A04111 A04112 A04113 Plated A04211 A04212 A04213 Painted A04311 A04312 A04313 10 9.3 Hasps (see 6 for required tests) Not

29、 Treated A83131 A83132 A83133 Plated A83231 A83232 A83233 Painted A83331 A83332 A83333 Safety Hasp Adjustable Staple Not Treated A83141 A83142 A83143 Plated A83241 A83242 A83243 Painted A83341 A83342 A83343 Safety Hasp Fixed Staple Safety Hasp Rotating Post Not Treated A83151 Plated A83251 Painted A

30、83351 Safety Hasp Swivel Staple Safety Hasp Latching Post Not Treated A83162 A83163 Plated A83262 A86263 Open Hinged Hasp with Fixed Staple Not Treated A83171 A83172 A83173 Plated A83271 A83272 A83273 Double or Multi-link Hinged Hasp with Fixed Staple 11 Not Treated A83181 Plated A83281 Painted A833

31、81 Heavy Open Hinged Hasp with Fixed Staple Not Treated A03191 A03192 A03193 Plated A03291 A03292 A03293 Painted A03391 A03392 A03393 Key-locking Hasp Not Treated A03141 A03142 A03143 Plated A03241 A03242 A03243 Painted A03341 A03342 A03343 Flexible Hasp (multi-link optional) 12 FIGURE 1 (See Table

32、I) 13 APPENDIX A (not a part of ANSI/BHMA A156.20) A-1 CONFORMANCE CRITERIA Certification that products offered meet the requirements of this Standard and conform to individual manufacturers drawings, specifications, standards and quality assurance practices are available and in some circumstances a

33、re required. Buyer requirements determine the need for proof of conformance such as first article inspection, test laboratory reports, or listings. Specifiers requiring assertions of conformance utilize statements of conformance by individual manufacturers, or test reports acceptable to the buyer. A

34、-2 PRESERVATION, PACKAGING AND PACKING Unless other arrangements between buyer and seller are made, preservation, packaging and packing shall be sufficient to protect containers and their contents under normal shipping and handling conditions from the source of supply to the destination point. A-3 M

35、ARKING Unless other arrangements between buyer and seller are made, marking shall be in accordance with the individual manufacturers standard practice. A-4 SECURITY This Standard covers commodity hasps and if security is an objective, additional criteria covering security attributes is to be conside

36、red. A-5 FINISHES If specific decorative or protective finishes are desired, they shall be specified. Users of this Standard correlate corrosion resistance with the third digit in the specified product type number as shown in 8.4 and the salt spray exposure time in 7.2. A-6 GRADES Users of this Standard select product as to grade desired. Grade designation is based on performance criteria with grade 1 subject to the severest test.