ANSI ASTM F1865-2009 Standard Specification for Mechanical Cold Expansion Insert Fitting With Compression Sleeve for Cross-linked Polyethylene (PEX) Tubing.pdf

《ANSI ASTM F1865-2009 Standard Specification for Mechanical Cold Expansion Insert Fitting With Compression Sleeve for Cross-linked Polyethylene (PEX) Tubing.pdf》由会员分享，可在线阅读，更多相关《ANSI ASTM F1865-2009 Standard Specification for Mechanical Cold Expansion Insert Fitting With Compression Sleeve for Cross-linked Polyethylene (PEX) Tubing.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F1865 09 An American National StandardStandard Specification forMechanical Cold Expansion Insert Fitting With CompressionSleeve for Cross-linked Polyethylene (PEX) Tubing1This standard is issued under the fixed designation F1865; the number immediately following the designation indicate

2、s the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers mechanical cold exp

3、ansioninsert fittings with compression sleeve suitable for use withcross-linked polyethylene PEX plastic tubing in38,12,58,34 ,and 1in. and larger nominal diameters that meet the require-ments of Specifications F876 and F877. These fittings areintended for use in 100 psi (689.5 kPa) cold and hot wat

4、erdistributions systems operating at temperatures up to andincluding 180 F (82C). Included are the requirements formaterials, workmanship, dimensions, and markings to be usedon the fittings and compression sleeves1.2 The values stated in inch-pound units are to be regardedas standard. The values giv

5、en in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish

6、appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2B16/B16M Specification for Free-Cutting Brass Rod, Barand Shapes for Use in Screw MachinesB140/B140M Specification for Copper-Zinc-Lead (RedBras

7、s or Hardware Bronze) Rod, Bar, and ShapesB283 Specification for Copper and Copper-Alloy Die Forg-ings (Hot-Pressed)D1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsE18 Test Methods for Rockwell Hardness of Me

8、tallic Ma-terialsF412 Terminology Relating to Plastic Piping SystemsF876 Specification for Crosslinked Polyethylene (PEX) Tub-ingF877 Specification for Crosslinked Polyethylene (PEX) Hot-and Cold-Water Distribution Systems2.2 ASME Standards:3B 1.20.1 Pipe Threads General Purpose (inch)B 16.18 Cast C

9、opper Alloy Solder Joint Pressure FittingsB 16.22 Wrought Copper and Copper Alloy Solder JointPressure Fittings2.3 NSF International Standards:4NSF 14 Plastic Piping Components and Related MaterialsNSF 61 Drinking Water System Components-Health Effects2.4 MSS Standard:5SP-104 Wrought Copper Solder J

10、oint Pressure Fittings3. Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nology F412 and abbreviations are in accordance with Termi-nology D1600 unless otherwise indicated.4. Classification4.1 This specification covers one class of mechanical coldexpansion insert fittings with com

11、pression sleeve suitable foruse with PEX tubing that meets the requirements of Specifi-cation F876 and F877.5. Materials and Manufacture5.1 FittingsThe fittings shall be made from one of thefollowing metals:1This specification is under the jurisdiction of CommitteeF17 on Plastic PipingSystems and is

12、 the direct responsibility of SubcommitteeF17.10 on Fittings.Current edition approved Dec. 1, 2009. Published January 2010. Originallyapproved in 1998. Last previous edition approved 2009 as F186502a(2009). DOI:10.1520/F1865-09.2For referenced ASTM standards, visit the ASTM website, www.astm.org, or

13、contact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American Society of Mechanical Engineers (ASME), ASMEInternational Headquarters, Three Park Ave., New York, NY 10016-

14、5990, http:/www.asme.org.4Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., AnnArbor, MI 48113-0140, http:/www.nsf.org.5Available from Manufacturers Standardization Society of the Valve and FittingsIndustry (MSS), 127 Park St., NE, Vienna, VA 22180-4602, http:/www.mss-.*A Summar

15、y of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established i

16、n the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.15.1.1 Machined Brass FittingsMachined brass fittingsshall be made from material meeting the requirements ofSpecif

17、ication B140/B140M CopperAlloy UNS C31400, Speci-fication B16/B16M Copper Alloy UNS C38500, or CopperAlloy UNS No. C27450, or DIN 17660 CuZn39Pb3.5.1.2 Forged Brass FittingsForged brass fittings shall bemade from material meeting the requirements of SpecificationB283 Copper Alloy UNS C37700, or Copp

18、er Alloy UNS No.C27450, or DIN 17660-CuZn40Pb2.5.1.3 Compression SleevesCompression sleeves shall bemade from material meeting the requirements of SpecificationB140/B140M Copper Alloy UNS C37700, Specification B16/B16M Copper Alloy UNS C38500, or DIN 17660-CuZn39PB3.6. General Requirements6.1 The fo

19、llowing sections of Specification F877 constitutea part of this specification:6.1.1 Requirements,6.1.2 Test Methods, and6.1.3 Retest and Rejection6.2 In addition, when a section with a title identical to thatreferenced in 6.1, above, appears in this specification, itcontains additional requirements

20、that supplement those appear-ing in F877.6.3 DimensionsRandomly selected fitting or fittings shallbe used to determine dimensions. Measurements shall be madein accordance with Test Method D2122. Determine the diam-eters by making measurements at four points spaced approxi-mately 45 apart around the

21、circumference. Inspection andgauging of solder joint ends shall be in accordance with ANSIB16.18, ANSI B16.22, or MSS SP-104. Inspection and gaug-ing of taper pipe threads shall be in accordance with ANSI/ASME G1.20.1. All fittings that will be subjected to secondaryprocesses of mechanical marking t

22、hat affect their dimensionaltolerances shall be tested in their final marked configuration.7. Dimensions7.1 Dimensions and TolerancesThe dimensions and toler-ances of fittings and compression sleeves shall be as shown inFig. 1 and Fig. 2 when measured in accordance with 6.3.Standard Size InchesABCDE

23、FGEWLRibWidth TypNumberof RibsGapWidth TypStopDia. minInsideDia. minInsertDiameterRibDiameterMinimumWallEXDepth38 in. 0.04 + 0.01 4 0.071 0.010 0.620 0.30 0.370 + 0.008 0.410 + 0.008 0.025 0.020 0.5912 in. 0.04 + 0.01 4 0.071 0.010 0.78 0.40 0.510 + 0.008 0.540 + 0.008 0.040 0.030 0.5958 in. 0.04 +

24、0.01 4 0.071 0.010 0.86 0.51 0.630 + 0.008 0.670 + 0.008 0.045 0.030 0.5934 in. 0.04 + 0.01 5 0.102 0.010 1.00 0.59 0.730 + 0.008 0.780 + 0.008 0.050 0.035 0.831 in. 0.04 + 0.01 5 0.126 0.010 1.40 0.77 0.900 + 0.008 0.950 + 0.008 0.055 0.035 0.94Metric millimetersSize A B C D E F G EW LSTD (nom) Rib

25、Width TypNumberof RibsGapWidth TypStopDia. minInsideDia. minInsertDiameterRibDiameterMinimumWallEXDepth38 in. (10 mm) (1 0.25) 4 (1.8 0.25) (16) (7.70) (9.5 + 0.2) (10.3 + 0.2) (0.63) (0.50) (15)12 in. (13 mm) (1 0.25) 4 (1.8 0.25) (20) (10.3) (13.0 + 0.2) (13.8 + 0.2) (1.0) (0.80) (15)58 in. (16 mm

26、) (1 0.25) 4 (1.8 0.25) (22) (12.9) (16.0 + 0.2) 17.0 + 0.2) (1.14) (0.80) (15)34 in. (19 mm) (1 0.25) 5 (2.6 0.25) (27) (15.0) (18.6 + 0.2) (19.8 + 0.2) (1.27) (0.89) (21)1 in. (25 mm) (1 0.25) 5 (3.2 0.25) (34) (19.5) (22.9 + 0.2) (24.0 + 0.2) (1.40) (0.89) (24)FIG. 1 Mechanical Insert Dimensions

27、and TolerancesF1865 0927.1.1 AlignmentThe maximum angular variation of anyopening shall not exceed12 off the true centerline axis.7.1.2 Fittings with Solder Joint EndsSolder joint endsshall be in accordance with ASME B 16.22, ASMEB 16.18B 16.18 or MSS SP-1047.1.3 Tapered Threaded EndsFitting threads

28、 shall beright-hand conforming to ASME B 1.20.1. They shall be taperthreads (NPT).8. Workmanship, Finish and Appearance8.1 The sealing, mating and threaded surfaces of the fit-ting(s) shall be smooth and free of foreign material. The fittingwalls shall be free of cracks, holes, blisters, voids, fore

29、igninclusions, or other defects that are visible to the unmagnifiedeye and that may affect the wall integrity.9. Assembly9.1 JointsMechanical Cold Expansion Insert Fittings withCompression Sleeve shall be joined to the PEX tubing bydrawing a compression sleeve over the PEX tubing that hasbeen cold e

30、xpanded and into which the fitting has beeninserted. This action forces the tubing into annular spacesformed by ribs on the fitting. Fittings and compression sleevesshall meet the dimensional tolerances of this Specification.PEX tubing shall meet the requirements of Specification F876or F877.Standar

31、d InchesSize H I J K M IWInside Diameter Groove Diameter Outside Diameter Length Groove Recess Chamfer Depth38 in. 0.52 0.002 0.56 0.01 0.63 0.01 0.59 0.02 0.14 0.0412 in. 0.66 0.002 0.7 0.01 0.75 0.01 0.59 0.02 0.14 0.0458 in. 0.80 0.002 0.84 0.01 0.94 0.01 0.59 0.02 0.14 0.0434 in. 0.93 0.002 0.97

32、 0.01 1.1 0.01 0.73 0.02 0.17 0.041 in. 1.15 0.002 1.19 0.01 1.3 0.01 0.91 0.02 0.22 0.04Metric millimetresSize H I J K M IWSTD (nom) Inside Diameter Groove Diameter Outside Diameter Length Groove Recess Chamfer Depth38 in. (10 mm) (13.20 0.05) (14.2 + 0.15) (16.00 0.25) (15.0 0.5) (3.5) (1)12 in. (

33、13 mm) (16.75 0.05) (17.75 + 0.15) (19.00 0.25) (15.0 0.5) (3.5) (1)58 in. (16 mm) (20.35 0.05) (21.3 + 0.15) (24.00 0.25) (15.0 0.5) (3.5) (1)34 in. (19 mm) (23.6 0.05) (24.5 + 0.15) (28.00 0.25) (18.5 0.5) (4.25) (1)1 in. (25 mm) (29.25 0.05) (30.2 + 0.15) (33.00 0.25) (23.0 0.5) (5.6) (1)FIG. 2 D

34、imensions and Tolerances of Fittings and Compression SleevesF1865 0939.1.1 Solder Joints Soldering of fittings joints shall becompleted prior to installation of the PEX tubing. Excessiveheat from the soldering operation will damage the PEX tubing.9.2 Assembly ProcedureTo affix the mechanical cold ex

35、-pansion insert fitting with compression sleeve to the PEXtubing, the procedure shall be as follows: Cut the tubing squareusing a cutter designed for plastic tubing. Inspect the end forburrs or foreign debris. Slide the compression sleeve onto thetubing at least 1 in. (25 mm) beyond the end of the t

36、ube. Insertthe properly sized expansion tool (see Note 1) fully into thetubing until the end of the tube meets the stop on the tool.Expand the tubing to the fullest reach of the tool. The fullestreach of the tool shall not expand the inside diameter of thetubing more than 0.20 in. (5.0 mm) for sizes

37、 up to58 in.nominal and 0.24 in. (6.0 mm) for larger sizes up to 1 in. Insertthe fitting into the expanded tube. Place the joining tool ontothe fitting assembly in accordance with the tool manufacturersinstructions (see Note 1). Operate the joining tool to slide thecompression sleeve over the tubing

38、 and until it reaches the stopon the fitting. Remove the joining tool. Compression sleevesthat are damaged in any way shall not be re-used.NOTE 1Tool manufacturers provide a variety of expansion tools andjoining tools with adapters for use on the various fittings configurationsand sizes. These tools

39、 may utilize mechanical, electrical, hydraulic, orpneumatic devices to actuate their mechanisms. One inch sizes may notrequire expansion.10. Quality Assurance10.1 When the product or product packing is marked withtheASTM designation F1865, the manufacturer affirms that theproduct was manufactured, i

40、nspected, sampled, and tested inaccordance with this specification, and has been found to meetthe requirements of this specification.11. Product Marking11.1 Quality of MarkingThe marking shall be applied tothe fittings in such a manner that it remains legible afterinstallation and inspection.11.2 Co

41、ntent of Marking:11.2.1 Marking on fittings shall include manufacturersname or trademark, or some other identifying mark. Additionalmarking shall includeASTM standard number and PEX, if sizepermits.11.2.1.1 Where recessed marking is used on fittings, careshall be taken to see that in no case shall t

42、he marking causecracks or reduce the wall thickness below the minimumspecified.11.2.2 Marking on packaging shall include manufacturersname, fitting size, and ASTM F1865.11.2.3 Markings on compression sleeves shall includemanufacturers trademark or some other identifying mark andASTM F1865.11.3 When

43、the product is marked with this ASTM designa-tion ASTM F1865, the manufacturer affirms that the productwas manufactured, inspected, sampled, and tested in accor-dance with this specification and has been found to meet therequirements of this specification.12. Keywords12.1 cold and hot water distribu

44、tion; cold expansion insertfittings; compression sleeve; crosslinked polyethylene; PEXSUPPLEMENTARY REQUIREMENTSThis requirement applies whenever a regulatory authority or user calls for product to be used toconvey or be in contact with potable water.S1. Potable Water Requirements Products intended

45、forthe transport of potable water shall be evaluated, tested, andcertified for conformance with ANSI/NSF Standard No. 61 orthe health effects portion of NSF Standard No. 14 by anacceptable certifying organization when required by the regu-latory authority having jurisdiction.SUMMARY OF CHANGESCommit

46、tee F17 has identified the location of selected changes to this standard since the last issue(F186502a(2009) that may impact the use of this standard.(1) Copper Alloy UNS No. C27450 was added to 5.1.1 and5.1.2.F1865 094ASTM International takes no position respecting the validity of any patent rights

47、 asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any ti

48、me by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will

49、receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single