ANSI ASTM F1025-1994 Standard Guide for Selection and Use of Full-Encirclement-Type Band Clamps for Reinforcement or Repair of Punctures or Holes in Polyethylene Gas Pressure Pipe《.pdf

《ANSI ASTM F1025-1994 Standard Guide for Selection and Use of Full-Encirclement-Type Band Clamps for Reinforcement or Repair of Punctures or Holes in Polyethylene Gas Pressure Pipe《.pdf》由会员分享，可在线阅读，更多相关《ANSI ASTM F1025-1994 Standard Guide for Selection and Use of Full-Encirclement-Type Band Clamps for Reinforcement or Repair of Punctures or Holes in Polyethylene Gas Pressure Pipe《.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F1025 94 (Reapproved 2011) An American National StandardStandard Guide forSelection and Use of Full-Encirclement-Type Band Clampsfor Reinforcement or Repair of Punctures or Holes inPolyethylene Gas Pressure Pipe1This standard is issued under the fixed designation F1025; the number immed

2、iately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This

3、guide specifically addresses the design and instal-lation of full-encirclement-type band clamps for repair ofgouges, punctures, or holes, and for reinforcement of polyeth-ylene plastic pipe. Guidelines are provided for selecting andusing clamps in pipe sizes 2 in. nominal (60 mm) and larger.1.1.1 A

4、test method is also provided for the user to assessthe applicability of the repair clamp. Under appropriatecircumstances, this type of clamp offers a convenient, effective,and safe means of restoring the integrity of an in-servicepipeline, without cutting out a section of pipe (see Note 1). Thepipe

5、to be repaired cannot be backed by a stiffener for internalsupport and cross-sectional dimensional control. Satisfactoryuse of this type of clamp must rely on the crush resistance ofthe pipe itself and a fitting design concept, which retains thecross-sectional pipe configuration while minimizing com

6、pres-sive forces required to obtain an effective leakage seal.NOTE 1The appropriateness for use of this type of clamp should bedetermined by using the information contained in this guide and fromconsultation with, and recommendations of, both the pipe and clampmanufacturers. The basic premise for us

7、e of this type of clamp is that it isrecommended by the manufacturer for this specific application and thatstep-by-step installation instructions are available for that application. It isimportant in the development of this type of clamp that prototype testingbe conducted to evaluate performance exp

8、ectations because of thephysical limitations encountered when designing it for use with plasticpipe.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not consi

9、dered standard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.

10、2. Referenced Documents2.1 ASTM Standards:2F1041 Guide for Squeeze-Off of Polyolefin Gas PressurePipe and Tubing3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 creepthe time-dependent part of strain resultingfrom stress, that is, dimensional change caused by the appli-cation o

11、f load over and above the elastic deformation and withrespect to time.4. Significance and Use4.1 Full-encirclement-type band clamps are recommendedfor repairs only where the pipe is able to maintain its structuralintegrity. These clamps are not recommended for permanentrepair of pipe where the damag

12、e could propagate outside theclamp under anticipated field conditions (see 5.1.1 for repairlimitations). In such situations, cut out and replace the dam-aged pipe with a new piece.4.2 These clamps may be used to cover holes left in the pipefrom abandoned service line connections, purge points, andac

13、cidental punctures.4.3 These clamps may be used to reinforce the pipe wherethe wall thickness has been reduced because of gouges or otherirregularities.4.4 Some users reinforce polyethylene pipe after it has beensqueezed-off as a precaution against pipe damage that mayhave occurred during the squeez

14、e-off process and as a means ofensuring that the pipe will not be squeezed-off again at thesame location. Consult with the polyethylene pipe manufac-turer as to the appropriateness of squeeze-off for their product,and for circumstances when reinforcement is recommended.See Guide F1041.1This guide is

15、 under the jurisdiction of ASTM Committee F17 on Plastic PipingSystems and is the direct responsibility of Subcommittee F17.60 on Gas.Current edition approved Aug. 1, 2011. Published August 2011. Originallyapproved in 1986. Last previous edition approved in 2006 as F1025 94 (2006).DOI: 10.1520/F1025

16、-94R11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, P

17、O Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued

18、by the World Trade Organization Technical Barriers to Trade (TBT) Committee.15. General Considerations5.1 The following general considerations apply to determinethe appropriateness of using full-encirclement-type bandclamps:5.1.1 Type or Extent of FailureConsider repairs only to aclean-cut round hol

19、e or deep scratches or gouges of maximumdimension, less than the nominal diameter of the pipe dividedby three. Do not repair pipe with cracks, jagged punctures, longtears, or deep scratches or gouges which could propagateoutside the clamp under anticipated field loads. Cut out andreplace the damaged

20、 pipe with a new piece.5.1.2 Pipe/Clamp ProfileThis type of clamp is usuallymade from flexible materials which have minimal ring stiff-ness. The clamp, by design, must rely on the pipe itself for anassembled profile and resistance to deformation from second-ary loading.5.1.3 Creep Properties of Pipe

21、 Material Creep propertiesaffect both the pipe strength and its dimensional change. Asresistance to creep increases, stiffness increases and dimen-sional change decreases.5.1.4 Minimum Pipe SizeNormally full-encirclement-typeband clamps have a minimum pipe size limitation due to thebasic design char

22、acteristics and the need to develop minimumsealing pressures against the pipe. The pipe must also be strongenough to resist anticipated secondary loading.5.1.5 Pipe Dimension Ratio (DR)The DR is determinedby dividing the specified average outside diameter of the pipeby the minimum specified wall thi

23、ckness.Alower DR providesgreater resistance to pipe deformation and creep.5.1.6 In-service Internal PressureHigher pressures tend tointernally support the existing pipe dimensions and roundprofile.5.1.7 In-service Operating Temperature Increased tem-peratures lower pipe stiffness and creep resistanc

24、e.6. Design Recommendations6.1 Properly designed full-encirclement-type band clampsshould meet the following recommendations:6.1.1 Maximum allowable operating pressure (MAOP) of100 psig (689 kPa).6.1.2 Maximum and minimum allowable operating tem-perature limits are provided by the manufacturer.6.1.3

25、 All components of the clamp are made fromcorrosion-resistant material, such as stainless steel, fiber-reinforced composite, or other plastic approved for use onburied polyethylene gas piping.6.1.4 The clamp is designed and made of material whichdoes not cause the pipe profile (ring) to assume a dif

26、ferentshape after being installed.6.1.5 The clamp materials have sufficient long-term strengthto last as long as the expected life of the pipe being clamped.6.1.6 The clamp, including the gasket, encircles the pipeand provides 360 reinforcement of the pipe.6.1.7 The gasket material is suitable for t

27、he intended serviceand of such hardness that significant compression of the pipe isnot required to maintain a seal.6.1.8 The interface between the clamp and gasket materialmaintains the position of the gasket within the band configu-ration.6.1.9 The dimensions of the clamp compensate for expectedcir

28、cumferential compression of the pipe, thereby ensuring apressure seal when the pipe is in the contracted position.7. Installation Recommendations7.1 Refer to the general considerations stated in Section 5 ofthis guide to determine the appropriateness of using full-encirclement-type band clamps to re

29、pair plastic pipe.7.2 Select a clamp with a length at least 112 times thenominal diameter of the pipe, but not less than 9 in. (229 mm)long.7.3 Use on pipe which is clean and free of any irregularitiesthat affect its profile.7.4 Center the clamp over the area to be repaired.7.5 Install the clamp in

30、accordance with the clamp manu-facturers recommended procedures.7.6 Leak test the repaired area using an appropriate leakdetector to validate the repair.8. Test Method8.1 This test is recommended as a means for the user toassess the applicability of a candidate repair clamp for use withpolyethylene

31、gas pipe. The user may also wish to performadditional tests (that is, pipe deflection), relevant to the specificintended use.NOTE 2The manufacturer is responsible for selecting a test appropri-ate to the intended applications for its product. Repair limitations,installation requirements, and perform

32、ance expectations should be madeavailable to users by the manufacturer.NOTE 3It is not intended that this or any other user test be the only testmethod used for product qualification.8.2 Select a pipe specimen with a hole size slightly less thanthe nominal diameter of the pipe divided by 3 (that is,

33、 3 in.nominal (89 mm) SDR 11.0 pipe with 1.125-in. (26.6-mm)hole); and of sufficient length to extend at least 12 in. (305 mm)beyond both ends of the clamp being tested.8.3 Select a clamp as specified in 7.2, and center it over thearea to be tested.8.4 Install the clamp following the pipe and clamp

34、manu-facturers recommended installation procedures.8.5 Provide suitable end closures for pressure testing.8.6 Once installed, do not adjust the clamp or retorque bolts.8.7 At 73F (23C), pressurize the specimen to 100 psig(689 kPa) with suitable test fluid and check for leakage.Reduce the pressure to

35、 5 psig (34 kPa).8.7.1 Condition the specimen for 24 h at the lowest operat-ing temperature anticipated by the user. Check again forleakage. Allow the specimen to stabilize at room temperaturefor another 24 h and recheck for leakage.8.7.2 Condition the specimen for 24 h at the highestoperating tempe

36、rature anticipated by the user. Check again forF1025 94 (2011)2leakage. Allow the specimen to stabilize at room temperaturefor another 24 h and recheck for leakage.NOTE 4Most of the significant creep occurs within the first 1000 h.Since the application of a mechanical clamp on polyethylene pipe resu

37、ltsin a rapidly decreasing load because of the initial gasket and pipedeformation, laboratory installations, corroborated by field experience,indicate that visible deformation occurs within 24 to 48 h after the clampis installed. Further deformation with time is not of the magnitudenecessary to affe

38、ct the original pressure seal provided by a suitable clamp.8.8 Remove the clamp and end closures of the specimen andvisually inspect the inside and outside of the pipe that wasbeneath the clamp for cracks or other damage caused by theclamp.9. Rejection9.1 Any leakage detected during the test constit

39、utes failureof the specimen.9.2 Any signs of splitting or cracking in the pipe constitutesrejection of the specific pipe and clamp assembly being tested.10. Keywords10.1 damage; full-encirclement-type band clamp; hole; leakrepair; pipe reinforcement; plastic pipe; punctureASTM International takes no

40、 position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own respons

41、ibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed t

42、o ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the add

43、ress shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 94 (2011)3