ANSI ASTM F1018 REV A-1987 Standard Specification for Steel Emergency Gear Stowage Locker.pdf

《ANSI ASTM F1018 REV A-1987 Standard Specification for Steel Emergency Gear Stowage Locker.pdf》由会员分享，可在线阅读，更多相关《ANSI ASTM F1018 REV A-1987 Standard Specification for Steel Emergency Gear Stowage Locker.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F1018 87a (Reapproved 2017) An American National StandardStandard Specification forSteel Emergency Gear Stowage Locker1This standard is issued under the fixed designation F1018; the number immediately following the designation indicates the year oforiginal adoption or, in the case of re

2、vision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the design, material, andmanufacture of steel emergency gear stowage loc

3、kers.1.2 Emergency gear lockers shall be of four types (seeSection 3).1.3 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.2. Referenced D

4、ocuments2.1 ASTM Standards:2A36/A36M Specification for Carbon Structural SteelA276 Specification for Stainless Steel Bars and ShapesA366/A366M Specification for Commercial Steel (CS)Sheet, Carbon, (0.15 Maximum Percent) Cold-Rolled(Withdrawn 2000)3A513 Specification for Electric-Resistance-Welded Ca

5、rbonand Alloy Steel Mechanical TubingA563 Specification for Carbon and Alloy Steel NutsB36/B36M Specification for Brass Plate, Sheet, Strip, AndRolled BarB124/B124M Specification for Copper and Copper AlloyForging Rod, Bar, and ShapesB176 Specification for Copper-Alloy Die Castings2.2 ANSI Standards

6、:4ANSI B18.1.1 Small Solid RivetsANSI B18.6.3 Slotted and Recessed Head Machine Screwsand Machine Screw NutsANSI B18.21.1 Lock WashersANSI B27.2 Plain Washers2.3 Other Documents:ABS Rules for Building and Classing Steel Vessels5SSPC Specification 66AWS D1.1 Welding Code73. Classification3.1 Emergenc

7、y gear lockers shall be classified in four typesas follows:3.1.1 Type 1For stowage of one complete firemans outfit,conforming to all requirements of all sections, figures, anddetails of this specification.3.1.2 Type 2For stowage of two complete firemensoutfits, conforming to all requirements of all

8、sections, figures,and details of this specification.3.1.3 Type 3For stowage of one complete firemans outfit,with locker dimensions in accordance with Figs. 2-4 (dimen-sions only), and conforming to the requirements of 3.2, 3.3,4.1, 5.2.4, and Sections 6 and 7 inclusive.3.1.4 Type 4For stowage of two

9、 complete firemensoutfits, with locker dimensions in accordance with Figs. 2-4(dimensions only), and conforming to the requirements of 3.2,3.3, 4.1, 5.2.4, and Sections 6 and 7 inclusive.3.2 One complete firemans outfit shall consist of thefollowing emergency gear (not included in this specification

10、):3.2.1 Self-contained breathing apparatus (24 by 14 by 11 in.(610 by 355 by 280 mm).3.2.2 Recharge air tank (7-in. (180-mm) diameter by 22 in.(560 mm) long).3.2.3 Set protective clothing, including helmet, gloves, andboots.3.2.4 Lifeline (150 ft (45 m), 18 by 18 by 10 in. (455 by 455by 255 mm).3.2.

11、5 Three-cell, explosion-proof flashlight with spare cells.3.2.6 Flame safety lamp.3.2.7 Fire axe.1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition a

12、pproved Jan. 1, 2017. Published January 2017. Originallyapproved in 1986. Last previous edition approved in 2010 as F1018 87a (2010).DOI: 10.1520/F1018-87AR17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of

13、ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.

14、ansi.org.5Available from American Bureau of Shipping (ABS), ABS Plaza, 16855Northchase Dr., Houston, TX 77060, http:/www.eagle.org.6Available from Society for Protective Coatings (SSPC), 800 Trumbull Dr.,Pittsburgh, PA 15205, http:/www.sspc.org.7Available from American Welding Society (AWS), 8669 NW

15、 36 St., #130,Miami, FL 33166-6672, http:/www.aws.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in

16、the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.13.3 In addition to the equipment listed in 3.2, each lockershall contain space for the following (not part of this

17、specifi-cation):3.3.1 First-aid kit, (1), (10 by 10 by 7 in. (255 by 255 by 180mm).3.3.2 Spare air tanks, as space allows (see Figs. 2-4).4. Ordering Information4.1 Order using this ASTM designation, year of issue,locker type, and finish.5. Materials and Manufacture5.1 MaterialsMaterials shall be as

18、 specified in Table 1.5.2 Manufacture:5.2.1 Mandatory dimensions and construction details forTypes 1 and 2 are as depicted in Figs. 1-9.5.2.2 Mandatory dimensions for Types 3 and 4 are as shownin Fig. 2, Fig. 3, and Fig. 5, respectively, and applicable detailsof Sections “A-A and “B-B.Alternative co

19、nstruction detailsare permissible.5.2.3 Construction details depicted in Figs. 4-9, while spe-cifically referring to locker Type 2, shall be adapted to suitlocker Type 1.5.2.4 Welded construction, in accordance with ABS Rulesfor Building and Classing Steel Vessels or AWS D1.1 Struc-tural Welding Cod

20、e shall be used throughout, unless otherwisespecified.6. Dimensions and Tolerances6.1 Dimensions are as indicated.6.2 Tolerance6116 in. (1.5 mm).7. Workmanship, Finish, and Appearance7.1 Entire assembly shall be free of weld spatter, slag,splinters, sharp edges, burrs, projections, and other defects

21、 thatmay be hazardous to personnel.7.2 The locker shall be cleaned after assembly to a com-mercial finish in accordance with SSPC Specification 6.7.3 Unless otherwise required by the ordering documents,the unit shall have the manufacturers standard baked-onenamel finish.7.3.1 The color shall be spec

22、ified in the ordering documents.8. Keywords8.1 emergency gear; firemans locker; firemans outfit;locker; steel locker; stowage lockerF1018 87a (2017)2TABLE 1 Parts List for Locker Type 2NOTE 11 in. = 25.4 mm.DescriptionItemNumberQuantityASTM, ANSIDocumentsLocker top sheet, 16 gage 39 in. long 30 in.

23、wide, carbon steel 1 1 A366/A366MLocker side, right sheet, 16 gage 72 in. long 2958 in. wide, carbonsteel21 A366/A366MLocker side, left sheet, 16 gage 72 in. long 2958 in. wide, carbonsteel31 A366/A366MLocker back sheet, 16 gage 72 in. long 3914 in. wide, carbonsteel41 A366/A366MLocker bottom sheet,

24、 16 gage 42 in. long 31 in. wide, carbon steel 5 1 A366/A366MDoor, right sheet, 16 gage 73 in. long 25 in. wide, carbon steel 6 1 A366/A366MDoor, left sheet, 16 gage 73 in. long 23 in. wide, carbon steel 7 1 A366/A366MShelf, full-width sheet, 16 gage 40 in. long 26 in. wide, carbon steel 8 2 A366/A3

25、66MShelf, half-width sheet, 16 gage 26 in. long 21 in. wide, carbon steel 9 2 A366/A366MPartition, vertical sheet, 16 gage 52 in. long 25 in. wide, carbon steel 10 1 A366/A366MCorner bracket sheet, 16 gage 512 in.long334 in. wide, carbonsteel11 4 A366/A366MLever handle, rightdoorcast brass 12 1 B176

26、 (UNS C86500)Keeper brass 13 1 B124/B124M (UNS C67500)Machine screw oval-head, #10-24 UNC-2A length to suit brass 14 14 ANSI B18.6.3B124/B124M (UNS C67500)Nut hexagon machine, #10-24 UNC-2B 15 14 ANSI B18.6.3brass B124/B124M (UNS C67500)Escutcheon sheet, 16 gage2in.long138 in. wide, brass 16 1 B36/B

27、36MLocking rod, upper round bar,516-in. diameter 37 in. long, carbon steel 17 1 A36/A36MLock rod, lower round bar,516-in. diameter 37 in. long, carbon steel 18 1 A36/A36MGuide, locking rod tube,12-in. outside diameter 0.065-in. wall thickness 118-in. long, carbon steel19 2 A513Latch sheet, 12 gage 3

28、1116 in.long2in.wide,carbonsteel20 1 A366/A366MReinforcing, latch sheet, 16 gage5in.long134 in. wide, carbon steel 21 1 A366/A366MLock washer38-in. nominal size, carbon steel 22 1 ANSI B18.21.1Rivet brazier head,532-in. diameter 23 2 ANSI B18.1.1Rivet flathead,316-in. diameter 24 2 ANSI B 18.1.1Insu

29、lation wool felt,364 in.thick2in.long138 in. wide 25 1Reinforcing clip sheet, 12 gage 112 in. square, carbon steel 26 1 A366/A366MReinforcing clip sheet, 16 gage 114 in. square, carbon steel 27 1 A366/A366MCam sheet, 12 gage 178 in. square, carbon steel 28 1 A366/A366MLatch filler sheet, 16 gage 278

30、 in.long212 in. wide, carbonsteel29 1 A366/A366MStrap sheet, 16 gage 212 in.long1in.wide,carbonsteel 30 1 A366/A366MNut hexagon,38-16 UNC-2B, carbon steel 31 1 A563Liner sheet, 16 gage 112 in.long118 in. wide, carbonsteel32 1 A366/A366MHinge sheet, 16 gage3in.long112 in. wide, carbon steelincluded:3

31、16-in. diameter 112-in. long stainless steelpin33 6 A366/A366MA276Lock washer316-in. nominal size,716-in. outside diameter, carbonsteel34 12 ANSI B18.21.1Liner, hinge sheet, 16 gage2in.long34 in. wide, carbon steel 35 6 A366/A366MLeg angle, 1118 6 in. long, carbon steel 36 4 A36/A36MFoot pad sheet,

32、10 gage 112 in. square, carbon steel 37 4 A366/A366MLeg bracket sheet, 10 gage8in.long3in.wide,carbonsteel 38 4 A366/A366MLeg reinforcement sheet, 10 gage8in.long134 in. widebend toform78-78 -in. angle, carbon steel39 4 A366/A366MMachine screw14-2OUNC-2A 34 in. long, carbon steel 40 16 ANSI B18.6.3N

33、ut hexagon machine,14-2OUNC-2B, carbon steel 41 16 ANSI B18.6.3Lock washer14-in. nominal size, carbon steel 42 16 ANSI B18.21.1F1018 87a (2017)3NOTE 11 in. = 25.4 mm.NOTE 2Approximately 2-in. high red lettering typical.FIG. 1 Emergency Gear Stowage LockerType 1F1018 87a (2017)4NOTE 11 in. = 25.4 mm.

34、NOTE 2Approximately 2-in. high red lettering typical.FIG. 2 Emergency Gear Stowage LockerTypes 2, 3, and 4F1018 87a (2017)5NOTE 11 in. = 25.4 mm.FIG. 3 Emergency Gear Stowage LockerTypes 2, 3, and 4 (Section “A-A”)F1018 87a (2017)6NOTE 11 in. = 25.4 mm.FIG. 4 CornerF1018 87a (2017)7NOTE 11 in. = 25.

35、4 mm.FIG. 5 Lock BoltF1018 87a (2017)8NOTE 11 in. = 25.4 mm.FIG. 6 Locking HandleF1018 87a (2017)9NOTE 11 in. = 25.4 mm.FIG. 7 LatchMiscellaneous DetailsF1018 87a (2017)10NOTE 11 in. = 25.4 mm.FIG. 8 LegF1018 87a (2017)11ASTM International takes no position respecting the validity of any patent righ

36、ts asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any

37、time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments wil

38、l receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by AST

39、M International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 11 in. = 25.4 mm.FIG. 9 Hinge and LinerF1018 87a (2017)12