ANSI ASTM F1015-2003 Standard Test Method for Relative Abrasiveness of Synthetic Turf Playing Surfaces《人造草皮运动场表面相对耐磨性的试验方法》.pdf
《ANSI ASTM F1015-2003 Standard Test Method for Relative Abrasiveness of Synthetic Turf Playing Surfaces《人造草皮运动场表面相对耐磨性的试验方法》.pdf》由会员分享,可在线阅读,更多相关《ANSI ASTM F1015-2003 Standard Test Method for Relative Abrasiveness of Synthetic Turf Playing Surfaces《人造草皮运动场表面相对耐磨性的试验方法》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F1015 03 (Reapproved 2009) An American National StandardStandard Test Method forRelative Abrasiveness of Synthetic Turf Playing Surfaces1This standard is issued under the fixed designation F1015; the number immediately following the designation indicates the year oforiginal adoption or,
2、 in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method is applicable to both laboratory andfield measurement of synthe
3、tic turf surfaces used for sports.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user
4、 of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C421 Test Method for Tumbling Friability of PreformedBlock-Type and Preformed Pipe-Covering-Type ThermalInsulatio
5、nE105 Practice for Probability Sampling of MaterialsE122 Practice for Calculating Sample Size to Estimate, WithSpecified Precision, the Average for a Characteristic of aLot or ProcessF355 Test Method for ImpactAttenuation of Playing SurfaceSystems and Materials3. Terminology3.1 Definitions of Terms
6、Specific to This Standard:3.1.1 synthetic turf playing surfacea man-made playingsurface incorporating artificial grass-like fibers.3.1.2 abrasivenessthat property of a synthetic turf whichcauses material in moving contact with the turf surface to wearaway.3.1.3 abrasiveness indexa number equal to th
7、e weight lostin grams per foot of travel of a standard weighted friable foamset multiplied by 100, when the foam is pulled through acomplete 1.8-m (6-ft) test cycle.3.1.4 foam friability indexa number equal to the percentmass loss of foam when tested in accordance with theProcedure section of Test M
8、ethod C421.4. Summary of Test Method4.1 Friable foam blocks are attached to a weighted platformwhich is pulled over the playing surface in a prescribedmanner. The weight of foam abraded away determines therelative abrasiveness of the surface.5. Significance and Use5.1 Data obtained from the procedur
9、e of this test method areindicative of the relative abrasiveness of fabric or carpet typesynthetic playing surfaces.6. Apparatus6.1 Abrasiveness Test PlatformA test platform is used tosupport the load on the friable foam material. The platformshall consist of a 20.3 by 20.3 cm (8.00 by 8.00 in.) squ
10、are of0.635-cm thick (0.25 in.) aluminum. Holes 0.635 cm indiameter shall be centered 0.635 cm from the midpoint of eachedge to permit attachment of a suitable hook for pulling. Foamretaining strips,14 in. high by12 in. wide, defining 2 by 2-in.squares, are attached at each corner (Fig. 1). The comp
11、letedplatform should weigh 931 6 28 g.6.2 Test WeightA flat-head (9.072-kg (20.00-lb) missileas used in Test Method F355, ProcedureA, can be used as a testweight. A suitable alternative weight is a steel cylinder about15.2 cm (6.00 in.) in diameter and about 6.35 cm (2.50 in.) inheight. The test wei
12、ght is to be within 56 g (2 oz) of itsspecified weight.6.3 Pull Cable and Direction Changing PulleyAdirectionchanging pulley attached to an operator foot restraint may beused to facilitate moving the loaded platform across the surfacewhile keeping the pull cable parallel to the surface. The pullcabl
13、e must not stretch under tension and must be equipped witha method of determining the distance pulled. For example,mechanical stops on either side of the direction changingpulley can be set to give the 45.7-cm (18-in.) pull length.1This test method is under the jurisdiction of ASTM Committee F08 on
14、SportsEquipment, Playing Surfaces, and Facilitiesand is the direct responsibility ofSubcommittee F08.65 on Artificial Turf Surfaces and Systems.Current edition approved July 1, 2009. Published August 2009. Originallyapproved in 1986. Last previous edition approved in 2003 as F1015 03. DOI:10.1520/F1
15、015-03R09.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive
16、, PO Box C700, West Conshohocken, PA 19428-2959. United States17. Test Foam37.1 The friable foam blocks used as the test material shall berigid closed-cell isocyanurate foam having a bulk density of0.0312 6 0.0008 g/cm3(1.95 6 0.05 lb/ft3). In addition, thetest foam must have a mass loss of 40 6 2 %
17、 as measured byTest Method C421. Test blocks must be cut to 5.08 by 5.08 by2.54 cm, 0.13 cm (2.00 by 2.00 by 1.00 in., 0.05 in.).8. Test Specimen8.1 Test specimens shall be representative of the playingsurface being evaluated. Fabrics used over a shock-absorbingpad should be tested after bonding to
18、that underpad.8.2 In the case of field evaluation abrasiveness, measure-ments should be made in representative areas of the field orspecific area of interest.9. Number of Specimens9.1 At least five specimens shall be tested and may berequired. In the case of field evaluation, five tests shall beperf
19、ormed, and may be required, in the area of interest or overthe entire playing surface depending on the intended data use.9.2 The sampling procedures of Recommended PracticesE105 and E122 should be followed and may be required.10. Sample Conditioning10.1 Field samples shall be under the intended usec
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
2000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ANSIASTMF10152003STANDARDTESTMETHODFORRELATIVEABRASIVENESSOFSYNTHETICTURFPLAYINGSURFACES 人造 草皮 运动场 表面
链接地址:http://www.mydoc123.com/p-432710.html