ANSI ASA S1.40-2006 AMERICAN NATIONAL STANDARD Specifications and Verification Procedures for Sound Calibrators《声音校准器的规格和核查程序》.pdf

《ANSI ASA S1.40-2006 AMERICAN NATIONAL STANDARD Specifications and Verification Procedures for Sound Calibrators《声音校准器的规格和核查程序》.pdf》由会员分享，可在线阅读，更多相关《ANSI ASA S1.40-2006 AMERICAN NATIONAL STANDARD Specifications and Verification Procedures for Sound Calibrators《声音校准器的规格和核查程序》.pdf（50页珍藏版）》请在麦多课文档分享上搜索。

1、 ANSI S1.40-2006 (Revision of ANSI S1.40-1984) AMERICAN NATIONAL STANDARD Specifications and Verification Procedures for Sound CalibratorsAccredited Standards Committee S1, Acoustics Standards Secretariat Acoustical Society of America 35 Pinelawn Road, Suite 114 E Melville, NY 11747-3177ANSI S1.40-2

2、006 Reaffirmed by ANSI on October 27, 2011 5HDIILUPHGE$16,6HSWHPEHUThe American National Standards Institute, Inc. (ANSI) is the national coordinator of voluntary standards development and the clearinghouse in the U.S.A. for information on national and international standards. The Acoustical Society

3、 of America (ASA) is an organization of scientists and engineers formed in 1929 to increase and diffuse the knowledge of acoustics and to promote its practical applications. ANSI S1.40-2006 (Revision of ANSI S1.40-1984) AMERICAN NATIONAL STANDARD Specifications and Verification Procedures for Sound

4、Calibrators Secretariat Acoustical Society of America Approved 20 September 2006: American National Standards Institute, Inc. Abstract This Standard specifies performance requirements for coupler-type sound calibrators. It replaces ANSI S1.40-1984 American National Standard Specifications for Acoust

5、ical Calibrators, and is technically equivalent (except for the absence of requirements for radio-frequency emissions) to International Standard IEC 60942:2003, ElectroacousticsSound calibrators. The standard specifies performance requirements for the sound pressure level, frequency, and total disto

6、rtion generated by a sound calibrator. It also provides requirements for the influence of environmental conditions, for electromagnetic compatibility, and for instrument marking and documentation. The standard gives details of the tests necessary to verify that a model of sound calibrator conforms t

7、o all the requirements, as well as details of the method for periodic testing of a sound calibrator. The tests require the determination of the actual uncertainties of measurement which are to not exceed the maximum uncertainties allowed for laboratory measurements. AMERICAN NATIONAL STANDARDS ON AC

8、OUSTICS The Acoustical Society of America (ASA) provides the Secretariat for Accredited Standards Committees S1 on Acoustics, S2 on Mechanical Vibration and Shock, S3 on Bioacoustics, and S12 on Noise. These committees have wide representation from the technical community (manufacturers, consumers,

9、trade associations, organizations with a general interest, and government representatives). The standards are published by the Acoustical Society of America as American National Standards after approval by their respective Standards Committees and the American National Standards Institute. These sta

10、ndards are developed and published as a public service to provide standards useful to the public, industry, and consumers, and to Federal, State, and local governments. Each of the accredited Standards Committees operating in accordance with procedures approved by American National Standards Institu

11、te (ANSI) is responsible for developing, voting upon, and maintaining or revising its own Standards. The ASA Standards Secretariat administers Committee organization and activity and provides liaison between the Accredited Standards Committees and ANSI. After the Standards have been produced and ado

12、pted by the Accredited Standards Committees, and approved as American National Standards by ANSI, the ASA Standards Secretariat arranges for their publication and distribution. An American National Standard implies a consensus of those substantially concerned with its scope and provisions. Consensus

13、 is established when, in the judgment of the ANSI Board of Standards Review, substantial agreement has been reached by directly and materially affected interests. Substantial agreement means much more than a simple majority, but not necessarily unanimity. Consensus requires that all views and object

14、ions be considered and that a concerted effort be made towards their resolution. The use of an American National Standard is completely voluntary. Their existence does not in any respect preclude anyone, whether he or she has approved the Standards or not, from manufacturing, marketing, purchasing,

15、or using products, processes, or procedures not conforming to the Standards. NOTICE: This American National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute require that action be taken periodically to reaffirm, revise, or withdraw this St

16、andard. Acoustical Society of America ASA Secretariat 35 Pinelawn Road, Suite 114E Melville, New York 11747-3177 Telephone: 1 (631) 390-0215 Fax: 1 (631) 390-0217 E-mail: asastdsaip.org 2006 by Acoustical Society of America. This Standard may not be reproduced in whole or in part in any form for sal

17、e, promotion, or any commercial purpose, or any purpose not falling within the provisions of the U.S. Copyright Act of 1976, without prior written permission of the publisher. For permission, address a request to the Standards Secretariat of the Acoustical Society of America. Acoustical Society of A

18、merica 2006 All rights reserved iContents 1 Scope . 1 2 Normative references. 2 3 Terms and definitions. 2 4 Reference environmental conditions 4 5 Requirements . 4 5.1 General . 4 5.2 Sound pressure level 6 5.3 Frequency. 8 5.4 Influence of static pressure, air temperature, and humidity 9 5.5 Total

19、 distortion 10 5.6 Power supply 11 5.7 Specification and calibration of microphones . 11 5.8 Electromagnetic compatibility . 12 6 Instrument marking and documentation. 13 6.1 Marking . 13 6.2 Individual calibration chart for a class LS sound calibrator 13 6.3 Instruction Manual 13 Annex A (normative

20、) Verification. 16 A.1 Introduction. 16 A.2 Verification sample size 16 A.3 Principal values. 17 A.4 Marking of the sound calibrator and supplied documentation 17 A.5 Performance tests at and around reference environmental conditions 17 A.6 Environmental tests 23 A.7 Electromagnetic compatibility .

21、32 Annex B (normative) Periodic tests . 35 B.1 Introduction. 35 B.2 Submission for test . 35 B.3 Preliminary inspection. 35 B.4 Performance tests. 36 B.5 Calibration of the sound calibrator with other models of microphone 38 B.6 Documentation 39 B.7 Bibliography for Annex B 40 Acoustical Society of

22、America 2006 All rights reserved ii Tables Table 1 Tolerance limits for sound pressure level and short-term level fluctuation, at and around reference environmental conditions . 7 Table 2 Tolerance limits for the influence of supply voltage on sound pressure level, at and around reference environmen

23、tal conditions . 7 Table 3 Tolerance limits for frequency, at and around reference environmental conditions. 8 Table 4 Tolerance limits for sound pressure level, over the specified range of environmental conditions . 9 Table 5 Tolerance limits for frequency, over the specified range of environmental

24、 conditions. 10 Table 6 Maximum total distortion 11 Table A.1 Maximum permitted expanded uncertainty of measurement for sound pressure level and short-term level fluctuation, at and around reference environmental conditions . 20 Table A.2 Maximum permitted expanded uncertainty of measurement for fre

25、quency, at and around reference environmental conditions . 21 Table A.3 Maximum permitted expanded uncertainty of measurement for total distortion, over the appropriate range of environmental conditions 22 Table A.4 Maximum permitted expanded uncertainty of measurement for sound pressure level, over

26、 the specified range of environmental conditions 24 Table A.5 Maximum permitted expanded uncertainty of measurement for frequency, over the specified range of environmental conditions 28 Acoustical Society of America 2006 All rights reserved iiiForeword This Foreword is for information only, and is

27、not an integral part of the American National Standard ANSI S1.402006 American National Standard Specifications and Verification Procedures for Sound Calibrators. This Standard comprises a part of a group of definitions, standards, and specifications for use in acoustics. It was developed and approv

28、ed by Accredited Standards Committee S1 Acoustics, under its approved operating procedures. Those procedures have been accredited by the American National Standards Institute (ANSI). The Scope of Accredited Standards Committee S1 is as follows: Standards, specifications, methods of measurement and t

29、est, and terminology in the field of physical acoustics, including architectural acoustics, electroacoustics, sonics and ultrasonics, and underwater sound, but excluding those aspects which pertain to biological safety, tolerances, and comfort. This Standard replaces ANSI S1.40-1984 (R2001), America

30、n National Standard Specifications for Acoustical Calibrators. This Standard is technically equivalent (except for the absence of requirements regarding radio-frequency emissions from calibrators) to International Standard IEC 60942:2003, Electroacoustics Sound calibrators. This Standard includes tw

31、o normative annexes that are considered to be integral parts of this Standard. At the time this Standard was submitted to Accredited Standards Committee S1, Acoustics for approval, the membership was as follows: J.P. Seiler, Chair G.S.K. Wong, Vice-Chair S.B. Blaeser, Secretary Acoustical Society of

32、 America. J.P. Seiler .G.S.K. Wong (Alt.) Air-Conditioning and Refrigeration Institute . S. Lind . D. Brown (Alt.) American Industrial Hygiene Association. D. Driscoll D. Sandfort (Alt.) Bruel FAX: 631-390-0217; E-mail: asastdsaip.org AMERICAN NATIONAL STANDARD ANSI S1.40-2006 Acoustical Society of

33、America 2006 All rights reserved 1American National Standard Specifications and Verification Procedures for Sound Calibrators 1 Scope Sound calibrators generate known sound pressure levels at one or more frequencies in a coupler into which a specified model of microphone is inserted in a specified c

34、onfiguration. NOTE An example of a specified configuration may be with or without a grid. This Standard specifies performance requirements and verification procedures for three classes of coupler-type sound calibrators: Class LS: Laboratory Standard calibrator with the smallest tolerance limits. Cla

35、ss 1: Sound calibrators that are generally intended for field use with class 1 sound level meters and similar instruments. Class 2: Sound calibrators that are generally intended for field use with class 2 sound level meters, dosimeters, and similar instruments. For class LS calibrators, the Standard

36、 requires the use of a laboratory standard microphone as specified in ANSI S1.15-1997/Part 1. For class 1 and class 2 calibrators, the Standard requires the use of a working standard microphone as specified in IEC 61094-4:1995. Tolerance limits in this Standard include maximum permitted expanded unc

37、ertainties of measurement as well as the tolerance limits allowed for design and manufacturing. This Standard applies to sound calibrators that are used to check or adjust the sensitivity of sound measuring instruments and systems including conventional, integrating-averaging and integrating sound l

38、evel meters, and personal noise dosimeters. This Standard does not include requirements for the Instruction Manual to provide data for use in adjusting a sound level indicated by a sound level meter, or equivalent instrument, in response to application of a sound calibrator to the equivalent free-fi

39、eld or random-incidence sound level. Sound calibrators may provide two or more sound pressure levels and operate at two or more frequencies. These multiple-level / multiple-frequency calibrators have a single class designation for all combinations of levels and frequencies for which the Instruction

40、Manual states conformance to the requirements of this Standard. Additional useful functions such as tonebursts may be provided. Requirements for these additional functions are not included in this Standard. ANSI S1.40-2006 Acoustical Society of America 2006 All rights reserved 2 2 Normative referenc

41、es The following referenced documents are indispensable for the application of this Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ANSI S1.1-1994 (R 2004), American National Sta

42、ndard Acoustical Terminology. ANSI S1.6-1984 (R 2006), American National Standard Preferred Frequencies, Frequency Levels, and Band Numbers for Acoustical Measurements. ANSI S1.15-1997/Part 1 (R 2006), American National Standard Measurement Microphones Part 1: Specifications for Laboratory Standard

43、Microphones ANSI S1.15-2005/Part 2, American National Standard Measurement Microphones Part 2: Primary Method for Pressure Calibration of Laboratory Standard Microphones by the Reciprocity Technique. IEC 61094-4:1995, Measurement microphones - Part 4: Specifications for working standard microphones

44、IEC 61094-5:2001, Measurement microphones - Part 5: Methods for pressure calibration of working standard microphones by comparison IEC 61000-4-2:1995, Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 2: Electrostatic discharge immunity test. Basic EMC Publicatio

45、n IEC 61000-4-3:1998, Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 3: Radiated, radio-frequency, electromagnetic field immunity test, Edition 1.1 IEC 61000-6-1:1997, Electromagnetic compatibility (EMC) Part 6: Generic standards Section 1: Immunity for reside

46、ntial, commercial and light-industrial environments IEC 61000-6-2:1999, Electromagnetic compatibility (EMC) Part 6: Generic standards Section 2: Immunity for industrial environments CISPR 22:1997, Information technology equipment Radio disturbance characteristics Limits and methods of measurement Gu

47、ide to the expression of uncertainty in measurement: 1995, ISBN: 9267101889 3 Terms and definitions For the purposes of this Standard, the terms and definitions given in ANSI S1.1-1994, and the following apply. 3.1 sound calibrator device that generates a sinusoidal sound pressure of specified sound

48、 pressure level and frequency when coupled to specified models of microphone in specified configurations ANSI S1.40-2006 Acoustical Society of America 2006 All rights reserved 33.2 specified sound pressure level sound pressure level(s) generated under reference environmental conditions for use with

49、a particular microphone model and configuration, valid for either an individual sound calibrator (in the case of a class LS sound calibrator) or all sound calibrators of the same model (in the case of a class 1 or class 2 calibrator) 3.3 nominal sound pressure level close approximation to the specified sound pressure level(s), valid for all sound calibrators of the same model, rounded to the nearest decibel (intended for marking) 3.4 specified frequency