ANSI American Society of Sanitary Engineering 1044-2015 Performance Requirements for Trap Seal Primer - Drainage Types and Electric Design Types.pdf

《ANSI American Society of Sanitary Engineering 1044-2015 Performance Requirements for Trap Seal Primer - Drainage Types and Electric Design Types.pdf》由会员分享，可在线阅读，更多相关《ANSI American Society of Sanitary Engineering 1044-2015 Performance Requirements for Trap Seal Primer - Drainage Types and Electric Design Types.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、Performance Requirements for Trap Seal Primer Drainage Types and Electric Design TypesASSE InternationalASSE Standard #1044-2015ASSE Board Approved: March 2015ANSI Approved: March 2015An American National StandardTrap Seal Primer Drainage Types and Electric Design Types iASSE Standard #1044-2015ASSE

2、 InternationalMokena, ILCopyright 2015, 2001, 1986All rights reserved.Neither this standard, nor any portion thereof, may be reproduced without the written consent of ASSE International.No product may be said to be listed by ASSE unless the manufacturer has applied to ASSE International, has had the

3、 product tested according to the applicable standards, and when the product has passed the test, displays the ASSE Seal on the product.Instructions for receiving the authorization to display the seal are available from the ASSE International office. Organizations wishing to adopt or list any ASSE st

4、andard should print the ASSE standard number on the cover page first in equal or larger type to that of the adopting or listing organization.General Informationii Trap Seal Primer Drainage Types and Electric Design Types ASSE Standard #1044-2015This foreword shall not be considered a part of the sta

5、ndard. However, it is offered to provide background information.ASSE standards are developed in the interest of consumer safety. The ASSE Product Standards Committee encourages manufacturers to develop performance requirement standards and testing procedures for their products. These standards have

6、the consensus of manufacturers and others who have pertinent interests in plumbing systems and are acceptable to this organization.For many years, the method of priming traps has been with the use of a water supply trap primer, which is activated by flow in the water supply piping. This method of pr

7、iming utilizes primers that comply with ASSE 1018, Performance Requirements for Trap Seal Primer Valves Potable Water Supplied. This standard addresses alternate methods to ASSE 1018 and addresses trap primers utilizing electric design and drainage-type trap seal primers.Although many of the materia

8、l specifications are detailed within Section 4.1 of this standard, it is the responsibility of the manufacturer and the installer to comply with the relevant jurisdictional requirements.The ASSE 1044 working group, which developed this standard revision, was set up within the framework of the ASSE I

9、nternational Product Standards Committee.Recognition is made of the time volunteered by members of the working group and of the support of manufacturers, who also participated in the meetings for this standard.This standard does not imply ASSE Internationals endorsement of a product that conforms to

10、 these requirements. Compliance with this standard does not imply acceptance by any code body.It is recommended that these trap seal primers be installed, consistent with local codes, by qualified and trained professionals.This standard was promulgated in accordance with procedures developed by the

11、American National Standards Institute (ANSI).This edition of the standard was approved by the ASSE International Product Standards Committee on Nov. 13, 2014 and approved by the Board of Directors on March 4, 2015 as an ASSE standard. ForewordTrap Seal Primer Drainage Types and Electric Design Types

12、 iiiASSE Standard #1044-2015iv Trap Seal Primer Drainage Types and Electric Design Types ASSE Standard #1044-2015Edward J. Lyczko, ChairpersonCleveland Clinic Retiree Cleveland, OHWilliam Briggs Jr.MGJ AssociatesNew York, NYTerry BurgerCSA GroupIndependence, OHMaribel CamposICC Evaluation ServicesWh

13、ittier, CAWilliam ChapinProfessional Code Consulting, LLCCullman, ALRon GeorgePlumb-Tech Design b) Those that are used in conjunction with ballcock assemblies;c) Those that receive flow from flushometer valves; andd) Those electric trap seal primers that discharge water automatically and are upstrea

14、m of the air gap or vacuum breaker.1.2.2 Fixture Connected TypeTubing size shall be not less than 1 NPS (32 DN) nominal size. Makeup water supply connection shall be a minimum of NPS (10 DN) nominal size.1.2.3 Ballcock Connected TypeMakeup water supply connections to the refill tube shall not be les

15、s than NPS (8 DN) nominal size.1.2.4 Flushometer Connected TypeMakeup type water supply connections shall be a minimum of NPS (10 DN) nominal size of chrome-plated copper, brass or stainless steel.1.2.5 Electric TypeThe minimum inlet size shall be NPS (15 DN). The minimum outlet size shall be NPS (1

16、0 DN)1.2.6 Working PressurePressurized trap seal primers shall be designed for a working water pressure range of 25.0 to 125.0 psi (172 to 861.8 kPa). 2 Trap Seal Primer Drainage Types and Electric Design Types ASSE Standard #1044-20151.2.7 Connections1.2.7.1 Tapered pipe threads shall comply with A

17、SME B1.20.1.1.2.7.2 Dry seal pipe threads shall comply with ASME B1.20.3.1.2.7.3 Compression assemblies shall comply with SAE J 512.1.2.7.4 Solder connection fittings shall comply with ASME B16.18, ASME B16.22, ASME B16.23 or ASME B16.29. 1.2.8 Fixture Tailpiece Trap Seal PrimersFixture trap or tail

18、piece trap seal primers shall consist of a 1 inch (32 mm) or larger tailpiece or trap assembly that is designed to connect to a supply tube that drains to the floor drain trap inlet.1.2.9 Ballcock Trap Seal PrimersBallcock trap seal primers shall consist of a refill tube diversion mechanism, a close

19、 coupled tank bolt/drain assembly, and related fittings for connection to the closet tank and ballcock. The diversion refill tube assembly shall be fitted with clear vinyl tubing, not less than inch (6.4 mm) inside diameter from the point of connection to the check member, a inch (6.4 mm) tee fittin

20、g, a check valve and a flow restrictor. Connections from the outlet of the close coupled tank connector tube shall not be less than inch (9.5 mm) outside diameter.1.2.9.1 Ballcock trap seal primer shall be used in conjunction with anti-siphon fill valves complying with ASSE 1002.1.2.10 Flushometer T

21、ailpiece/Trap Seal PrimersFlushometer tailpiece/trap seal primers shall be chrome-plated with minimum tailpiece wall thickness of 0.040 inch (1.0 mm) with a minimum inch (9.5 mm) outside diameter compression type chrome-plated brass fitting. Compression fittings shall comply with SAE J512.1.2.10.1 F

22、lushometer Tailpiece/Trap Seal Primer UseFlushometer tailpiece/trap seal primers shall only be used in conjunction with a flushometer complying with ASSE 1037 and shall be installed below the critical level of the vacuum breaker.1.2.11 Electric Trap Seal Primers1.2.11.1 Electric Trap Priming Assembl

23、yElectric trap priming assemblies shall comply with one or more of the following standards:a) UL 1951, Standard for Electric Plumbing Accessoriesb) CSA-C22.2 No. 68, Motor-Operated Appliances (Household and Commercial)1.2.11.2 Backflow ProtectionBackflow protection shall be installed at the discharg

24、e point and comply with ASSE 1001 or ASME A112.1.2.1.3 Reference Standards ASME A112.1.2-2012, Air Gaps in Plumbing Systems (For Plumbing Fixtures and Water-Connected Receptors ASME B1.20.1-2013, Pipe Threads, General Purpose (Inch) ASME B1.20.3-1976 (R2013), Dryseal Pipe Threads (Inch) ASME B16.18-

25、2012, Cast Copper Alloy Solder Joint Pressure Fittings ASME B16.22-2013, Wrought Copper and Copper Alloy Solder-Joint Pressure Fittings ASME B16.23-2011, Cast Copper Alloy Solder Joint Drainage Fittings: DWV ASME B16.29-2012, Wrought Copper and Wrought Copper Alloy Solder-Joint Drainage Fittings - D

26、WV ASSE 1001-2008, Performance Requirements for Atmospheric Type Vacuum BreakersTrap Seal Primer Drainage Types and Electric Design Types 3ASSE Standard #1044-2015 ASSE 1002-2008, Performance Requirements for Anti-Siphon Fill Valves for Water Closet Tanks ASSE 1037-1990, Performance Requirements for

27、 Pressurized Flushing Devices (Flushometers) for Plumbing Fixtures CSA 22.2 No. 68-09 (R2014), Motor-Operated Appliances (Household and Commercial) SAE J512-1997, Automotive Tube Fittings UL 1951-2014, Standard for Electric Plumbing Accessories 4 Trap Seal Primer Drainage Types and Electric Design T

28、ypes ASSE Standard #1044-2015Section II2.0 Test Specimens2.1 Samples TestedThree (3) trap seal primers of each size and model shall be submitted by the manufacturer. The testing agency shall select one (1) of each type or model and size for the full test. Tests shall be performed in the order listed

29、 on one (1) trap seal primer of each size submitted.2.2 DrawingsAssembly and installation drawings, and any other data that is needed to enable a testing agency to determine compliance with this standard shall accompany the trap seal primer when submitted for examination and performance testing unde

30、r this standard.2.3 RejectionFailure of one (1) trap seal primer shall result in a rejection of that type or model.Trap Seal Primer Drainage Types and Electric Design Types 5ASSE Standard #1044-2015Section III3.0 Performance Requirements and Compliance Testing3.1 Hydrostatic Test for Electric Type3.

31、1.1 PurposeThe purpose of this test is to evaluate high-pressure trap seal primers for hydrostatic integrity.3.1.2 ProcedureThe trap seal primer shall be connected to a water source that is capable of achieving 125.0 psi (861.8 kPa) or two (2) times the manufacturers maximum rated working pressure,

32、whichever is greater. Circulate water through the trap seal primer to purge the air. All outlets from the trap seal primer shall be sealed (the manufacturer shall be permitted to provide components to facilitate sealing of the outlets). The trap seal primer shall be pressurized to 125.0 psi (861.8 k

33、Pa) or two (2) times the manufacturers maximum rated working pressure, whichever is greater, for a period of 5 minutes. 3.1.3 CriteriaAny indication of external leakage shall result in a rejection of the trap seal primer.3.2 Verification of Manufacturers Performance Rating3.2.1 PurposeThe purpose of

34、 this test is to verify the flow rates as provided by the manufacturer.3.2.2 ProcedureThe manufacturer shall furnish the minimum discharge rate of flow through the supply line.3.2.2.1 Procedure for Fixture Tailpiece Trap Seal Primer The manufacturer shall specify the discharge rates over a period of

35、 1 minute through the primer line for faucet flow rates of 0.5 GPM (1.9 L/min) and 2.5 GPM (9.5 L/min) at 20.0 psi (138 kPa) pressure.Five (5) tests shall be run for a period of 1 minute each using a faucet with a flow rate of 0.5 GPM (1.9 L/min) at a pressure of 20.0 psi (138 kPa).A grid strainer s

36、hall be installed upstream of the primer. The volume of water collected by each test shall be recorded.3.2.2.2 CriteriaFailure to meet the manufacturers specified ratings on each test shall result in a rejection of the trap seal primer.3.2.2.3 Procedure for Ballcock Trap Seal Primer The trap seal pr

37、imer shall be installed, in accordance with the manufacturers instructions, in the tank of a 1.28 gallons per flush (gpf) (4.8 Lpf) closed coupled water closet. Water shall be added to the bowl and the water level shall then be marked with non-water soluble ink or marker. The tank shall be filled an

38、d the ballcock shall be operated at a static pressure of 40.0 psi (276 kPa) for a series of twenty (20) flushes. Repeat the test at a flowing pressure of 8.0 psi (55 kPa) for a series of twenty (20) flushes.6 Trap Seal Primer Drainage Types and Electric Design Types ASSE Standard #1044-20153.2.2.4 C

39、riteriaAny leakage from the tank bolt connection shall result in a rejection of the trap seal primer. Failure of the trap seal primer to demonstrate the minimum rated flow per Section 3.2.2 through the primer tube at either pressure shall result in rejection of the trap seal primer. Failure of the w

40、ater closet to reseal to full trap seal depth after each flush shall result in a rejection of the trap seal primer.3.2.2.5 Procedure for Flushometer Tailpiece/Trap Seal Primer The trap seal primer shall be installed between a 1.28 gpf (4.8 Lpf) flushometer valve and a water closet bowl in accordance

41、 with manufacturers instructions. The assembly shall be operated at a flowing pressure of 50.0 psi (345 kPa) for a series of twenty (20) flushes.3.2.2.6 CriteriaAny indication of leakage from any connection shall result in a rejection of the trap seal primer. Failure to achieve the minimum rated flo

42、w per Section 3.2.2 through the primer drain tube, per flush, shall result in rejection of the trap seal primer.3.2.2.7 Procedure for Electric Trap Seal PrimerThe trap seal primer shall be installed per the manufacturers instructions. A water supply shall be connected to the inlet and the trap seal

43、primer shall be pressurized to the manufacturers rated working pressure. The cycle “on” time shall be set to the lowest adjustable setting permitted on the device. The trap seal primer shall be activated for a period of five (5) cycles and the discharge from each outlet shall be measured.3.2.2.8 Cri

44、teriaFailure to achieve a minimum of 2.0 ounces (59 ml) per outlet during any test shall result in rejection of the trap seal primer.3.3 Cycle Test for Electric Trap Seal Primer3.3.1 PurposeThe purpose of this test is to determine any deterioration of performance upon completion of five thousand (5,

45、000) cycles.3.3.2 ProcedureThe trap primer seal shall be installed per the manufacturers instructions. A water supply shall be connected to the inlet and shall be pressurized to 50.0 psi (345 kPa). A method shall be employed to activate the trap seal primer for a period of five thousand (5,000) cycl

46、es. Each cycle shall consist of the manufacturers “on” cycle time, then 5 seconds off.3.3.3 CriteriaAny indications of failure or leakage during the cycle test shall result in a rejection of the trap seal primer.Trap Seal Primer Drainage Types and Electric Design Types 7ASSE Standard #1044-2015Secti

47、on IV4.0 Detailed Requirements4.1 Materials4.1.1 Solder and FluxesSolder and fluxes containing lead in excess of 0.2% shall not be used in contact with potable water. 4.1.2 Corrosion of Interior PartsAll metal parts, except springs, in contact with water shall have a corrosion resistance at least eq

48、ual to a copper alloy of not less than 58% copper.4.1.3 SpringsSprings in contact with water shall have a corrosion resistance at least equal to 300-series stainless steel.4.1.4 Elastomeric PartsDiaphragms, valve discs, seating facings or other flexible non-metallic parts shall be designed for conti

49、nuous exposure to water at the manufacturers maximum rated operating temperature of the trap seal primer without change in physical characteristics that would prevent full compliance with all requirements of this standard.4.2 Documentation4.2.1 Installation and MaintenanceFull instructions for proper installation and maintenance shall be packaged with the trap seal primer. The instructions shall include data to guide the installer in order to select the appropriate amount of water required for the designs of the mati