AIR FORCE MIL-R-25085 C (3)-1982 RACK BOMB AIRCRAFT ELECTRIC TYPE MB-3A A《 MB-3A A型轰炸机电动机架》.pdf

《AIR FORCE MIL-R-25085 C (3)-1982 RACK BOMB AIRCRAFT ELECTRIC TYPE MB-3A A《 MB-3A A型轰炸机电动机架》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE MIL-R-25085 C (3)-1982 RACK BOMB AIRCRAFT ELECTRIC TYPE MB-3A A《 MB-3A A型轰炸机电动机架》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-R-25085C (3) 20 7977706 0309378 7 I % -37-03 MIL-R-25085C (UsAl?) AMENDMENT 3 19 March 1982 SUPERSEDING AMENDMENT 2 9 MAY 1980 MILITARY SPECIFICATION RACK, BOMB AIRCRAFT, ELECTRIC, TYPE MB-3A/A This amendment forms a part of Military Specif icat ion MIL-R-25085C (US) dated 3 June 1959, and is ap

2、proved for use by the Department of the Air Force and is available for use by all Departments and Agencies of the Depart me n t of De fe ns e. PAGE 1 2.1: *Under “SPECIFICATION“ “FEDERAL“: Delete: QQ-2-325 Zinc Coating, Electrodeposit Add: QQ-P-4 16 Plating Cadium, Electrodeposit PAGE 3 Sect ion 3,

3、Under “REQUIREMENTS“ * Paragraph 3.3.1. Change I. in accordance with QQ-2-325“ to read I . in accordance with QQ-P-416.“ Add new paragraph: “3.3.4 Materials: the maximum extent possible in lieu of virgin raw materials as long as these materials do not jeopardize the intended use and fully comply wit

4、h the contract requirements. Materials used shall be free from defects which would adversely affect the performance or maintainability of individual components or the over- all assembly. Materials not specified herein shall be of the same quality used for the intended purpose in commercial practice.

5、 interpreted to mean that the use of used or rebuilt products will be allowed.“ Recycled and recovered raw materials should be used to None of the above shall be PAGE 4 Pa.ragrnph 3.5.4. read I . shall conform to MIL-L-7870.“ Change I. shall conform to MIL-3278 or MIL-L-7870“ to PAGE 6 Add the follo

6、wing new paragraph: Page 1 of 2 FSC 1095 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-R-25085C (3) LO 9799906 0304379 9 MIL-R-25085C (USAF) . AMENDMENT 2 “3.6.5.1 Safety Pin. The safety pin shall provide the means for preventing the bmb rack

7、from unlatching when the linkage is released. PAGE 10 Add the following new subparagraph: “3.6.1.2.f. A test store of not less than 1750 pounds shall be latched to the bomb rack. With the safety pin in position the release mechanism shall be triggered. When released the load shall be retained in the

8、 latched con- dition. A pull force of not less than 150 pounds shall be required to remove the safety pin and remove the load.“ * Identification of Changes. an asterisk to indicate where changes (additions, modifications, corrections, The margins of this amendment are marked with deletions) from the

9、 previous amendment were made. ience only and the Government assumes no reliability whatsoever for any in- accuracies in these notations. Bidders and contractors are cautioned to eval- uate the requirements of this document based on the entire content irrespective of the marginal notations and relat

10、ionship to the last previous amendment .I1 This was done as a conven- Change the Preparing Activity and Custodian to: Custodian: Preparing Activity: Air Force - 99 Air Force - 99 Project No. 1095-F165 Page 2 of 2 -. ft U.8. BOVERNMENT PRINTING OFFICE: l982-505-022/24i0 GI Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-