AIR FORCE MIL-HDBK-1568-1996 MATERIAL AND PROCESSES FOR CORROSION PREVENTION AND CONTROL IN AEROSPACE WEAPONS SYSTEMS《在航空航天武器系统工艺材料的预防腐蚀和控制》.pdf

《AIR FORCE MIL-HDBK-1568-1996 MATERIAL AND PROCESSES FOR CORROSION PREVENTION AND CONTROL IN AEROSPACE WEAPONS SYSTEMS《在航空航天武器系统工艺材料的预防腐蚀和控制》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE MIL-HDBK-1568-1996 MATERIAL AND PROCESSES FOR CORROSION PREVENTION AND CONTROL IN AEROSPACE WEAPONS SYSTEMS《在航空航天武器系统工艺材料的预防腐蚀和控制》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、NOTE: MIL-STD-1568B(USAF) has beenredesignated as a handbook and is to be usedfor guidance purposes only. This document isno longer to be cited as a requirement. Foradministrative expediency, the only physicalchange from MIL-STD-1568B(USAF) is thiscover page. However, this document is nolonger to be

2、 cited as a requirement. If cited asa requirement, contractors may disregard therequirements of this document and interpret itscontents only as guidance.INCH-POUNDMIL-HDBK-1568(USAF)18 JULY 1996SUPERSEDINGMIL-STD-1568B(USAF)12 October 1994MILITARY HANDBOOKMATERIALS AND PROCESSES FORCORROSION PREVENT

3、ION AND CONTROL INAEROSPACE WEAPONS SYSTEMSAMSC N/A FSC MFFPDISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking pe

4、rmitted without license from IHS-,-,-MIL-STD- 1568B(USAF)28 February 1989iFORWARD1. This military standard is approved for use by the Air Force and is available for use by allDepartments and Agencies of the Department of Defense.2. Beneficial comments (recommendations, additions, deletions) and any

5、pertinent data whichmay be of use in improving this document should be addressed to : ASC/ENISD, Wright-Patterson AFB OH 45433-7809, by using the self-addressed Standardization DocumentImprovement Proposal (DD Form 1426) appearing at the end of this document or by letter.3. The purpose of this stand

6、ard is to establish the requirements for materials, processes andtechniques, and to identify the tasks required to implement an effective corrosion prevention andcontrol program during the conceptual, validation, development and production phases ofaerospace weapons systems.Provided by IHSNot for Re

7、saleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD- 1568B(SUAF)28 February 1989ii1 SCOPE 11.1 Scope. 11.2 Intended use. . 11.3 Applicability. . 12 APPLICABLE DOCUMENTS . 12.1 Government Documents 12.1.1 Secifications and standards. . 12.1.2 Other Government documents, d

8、rawings, and publicat ions. 32.2 Non-Government publications. . 32.3 Order of precedence. . 43 DEFINITIONS 44 GENERAL REQUIREMENTS 44.1 General requirements. . 45 DETAIL REQUIREMENTS 55.1 Documentation. 55.2 Schedule for submission 55.2.1 Corrosion prevention a nd control plans. 55.2.2 System peculi

9、ar corrosion control technical order. 55.3 Implementation of corrosion prevention advisory board . 65.3.1 Corrosion prevention advisory board (CPAB) 65.3.1.1 Establishment. . 65.3.1.2 Membership. 65.3.2 Contractors corrosion team (CCT) 75.3.2.1 Membership . 75.3.2.2 CCT Duties. . 75.4 Materials and

10、process considerations in design . 85.4.1 Selection considerations. 85.4.2 General design guidelin es for corrosion prevention . 85.4.2.1 Exclusion of rain and airborne spray. . 85.4.2.2 Ventilation. . 85.4.2.3 Drainage. . 85.4.2.4 Dissimi lar metals. . 85.4.3 Metallic materials 95.4.3.1 Aluminum .

11、95.4.3.1.1 Alloy selection. . 95.4.3.1.2 Aluminum allov selection limitations. 95.4.3.1.3 Maximum metal removal. 95.4.3.1.4 Shot peening for stress corrosion resistance and fatigue life improvement. 115.4.3.1.5 Stress corrosion factor. . 115.4.3.2 Low alloy, high strength steels. 115.4.3.2.1 Limitat

12、ion on use of protective metallic coatings. 115.4.3.2.2 Stress corrosion factors. . 115.4.3.3 Corrosion resistant steels. 125.4.3.3.1 Corrosion resistant steels limitations. 125.4.3.4 Titanium . 125.4.3.4.1 Surface considerations. 125.4.3.4.2 Fretting. 125.4.3.4.3 Special precautions. . 125.4.3.5 Ma

13、gnesium. . 14Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD- 1568B(USAF)28 February 1989iii5.4.3.6 Beryllium. . 145.4.3.7 Mercu ry. . 145.4.3.8 Depleted uranium. 145.4.4 Insulating blankets. . 145.5 Corrosion prevention during manufacturing

14、operations. . 145.5.1 Cle aning. . 145.5.1.1 Titanium contamination. . 145.5.2 Surface damage. . 155.5.3 Marking pencils. 155.5.4 Cleaning after assembly. . 155.5.5 Protection of parts during storage and shipment. 155.6 Inorganic finishes . 155.6.1 Detail requirements. 155.6.1.1 Aluminum. 155.6.1.2

15、Cadmium coatings. 155.6.1.3 Aluminum coatings. 165.6.1.4 Magnesium. . 165.7 Organic finishes . 165.7.1 De tail requirements. 165.7.1.1 Organic finishes. 165.7.1.2 Organic finish applications. 165.7.1.3 Magnesium surfaces. . 165.8 Environmen tal Sealing . 165.8.1 Detail Requirements. . 165.9 Fastener

16、 installation . 175.9.1 Detail requirements. 175.9.2 Removable- fasteners. 175.9.3 Fasteners in titanium. 175.9.4 Monel and stainless steel fastener. . 175.9.5 Fasteners in graphite composites. . 175.9.6 Interferenc e fit fasteners. . 175.10 Special consideration 185.10.1 Cadmium plated parts. . 185

17、.10.2 Engine corrosion susceptibility testing. 185.10.3 Electronic or avionics systems . 195.10.3.1 Cleaning of printed wiring boards (PWBs). . 195.10.3.2 Conformal coatings. . 195.10.3.3 PWB orientation. 195.10.3.4 Hermetic sealing. . 195.10.3.5 Electrical connectors. . 195.10.3.6 General requireme

18、nt. . 196 INFORMATION FOR GUIDANCE ONLY . 196.1 Intended use. . 196.2 Issue of DoDISS. 206.3 Data requirements. . 206.4 Key words 206.5 Changes from previous issue. 20Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo rep

19、roduction or networking permitted without license from IHS-,-,-MIL-STD- 1568B(USAF)28 February 198911 SCOPE1.1 Scope.This standard establishes the requirements for materials, processes and techniques, andidentifies the tasks required to implement an effective corrosion prevention and control program

20、during the conceptual, validation, development and production phases of aerospace weaponsystems. The intent is to minimize life cycle cost due to corrosion and to obtain improvedreliability.1.2 Intended use.This standard is to provide a mechanism for implementation of sound materials selectionpracti

21、ces and finish treatments during the design, development, production and operationalcycles of the aerospace weapon systems. This standard defines requirements to ensureestablishment and implementation of a corrosion prevention advisory board (where applicable),a corrosion prevention and control plan

22、 and its accompanying finish specification as directed inSection 4. The corrosion prevention and control plan will dictate the organization of the boards,their basic duties, operating procedures, and the finish philosophies used in the systems. Thefinish specification will therefore be required to s

23、pecify the detailed finish and coating systems tobe used on the respective aerospace weapons system in accordance with the finishphilosophies as approved in the corrosion prevention and control plan. This standard is derivedfrom experience gained on protection of aerospace weapons systems against co

24、rrosion by themilitary services and industry. It represents technical guidance and requirements forincorporation in the corrosion prevention and control plan and finish specification.1.3 Applicability.This standard is applicable for use by all Air Force procuring activities and their respectivecontr

25、actors involved in the design and procurement of aerospace weapon systems. Thedetailed corrosion prevention and control plan and the finish specification applies to all elementsof aerospace weapon systems, including spares. Materials and processes required forcorrosion prevention and control in supp

26、ort equipment are covered in MIL-STD-808. Materialsand Process Requirements for Air Force Weapon Systems are covered in MIL-STD-1587. Thisstandard when used in conjunction with MIL-STD-808 and MIL-STD-1587 will result in reliableaerospace systems having a good balance between acquisition costs and l

27、ife cycle cost. Therequirement for the establishment of a corrosion prevention advisory board shall pertain tomajor aerospace systems approved for Air Force use as defined by AFR 800-2, AcquisitionProgram Management.2 APPLICABLE DOCUMENTS2.1 Government Documents2.1.1 Secifications and standards.The

28、following specifications and standards form a part of this specification to the extentspecified herein. Unless otherwise specified, the issues of these documents shall be thoselisted in the issue of the Department of Defense Index of Specifications and Standards(DODISS) and supplement thereto, cited

29、 in the solicitation. (See 6.2)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD- 1568B(SUAF)28 February 19892SPECIFICATIONSFEDERALQQ-P-35 Passivation Treatments for Corrosion-Resisting SteelQQ-N-290 Nickel Plating (Electrodeposited)QQ-P-416 Pl

30、ating, Cadmium (Electrodeposited)MILITARYMIL-M-3171 Magnesium Alloy, Processes for Pretreatment and Prevention ofCorrosionMIL-S-5002 Surface Treatments and Inorganic Coatings for Metal SurfacesMIL-C-5541 Chemical Conversion Coatings on Aluminum and Aluminum AlloysMIL-F-7179 Finishes, Coatings and Se

31、alants for the Protection of AerospaceWeapons SystemsMIL-A-8625 Anodic Coatings, for Aluminum and Aluminum AlloysMIL-S-8784 Sealing Compound Aluminum Integral Fuel Tanks and Fuel Cells,Cavities, Low Adhesion, Accelerator RequiredMIL-S-8802 Sealing Compound, Temperature Resistant, Integral Fuel Tanks

32、 andFuel Cell Cavities, High AdhesionMIL-C-8837 Coating, Cadmium (Vacuum Deposited)MIL-S-13165 Shot Peening of Metal PartsMIL-F-18264 Finishes: Organic, Aircraft: Application and Control ofMIL-P-23377 Primer Coating: Epoxy-Polyamide, Chemical and Solvent ResistantMIL-C-27725 Coatings, Corrosion Prev

33、entive, for Aircraft Integral Fuel TanksMIL-P-28809 Printed Wiring AssembliesMIL-M-38510 Microcircuit, General Specification forMIL-C-38999 Connector, Electrical, Circular, Miniature, High Density QuickDisconnect, Environment Resistant, Removable Crimp and HermeticSolder Contacts, General Specificat

34、ion forMIL-M-45202 Magnesium Alloys, Anodic Treatment ofMIL-I-46058 Insulating Compound, Electrical (for Coating Printed Wiring Boards)MIL-S-81733 Sealing and Coating Compound, Corrosion InhibitiveMIL-C-83231 Coatings, Polyurethane Rain Erosion Resistant for Exterior Aircraft andMissile Plastic Part

35、sMIL-C-83286 Coating, Urethane, Aliphatic, Isocyanate, for Aerospace ApplicationsMIL-S-83430 Sealing Compound, Integral Fuel Tanks and Fuel Cell Cavities,Intermittent Use to 360 o FMIL-C-83445 Coating Systems, Polyurethane, Non-Yellowing, White, Rain ErosionResistant, Thermally ReflectiveMIL-C-83488

36、 Coating, Aluminum, Ion Vapor DepositedMIL-P-83953 Pencil, Aircraft MarkingMIL-C-85582 Primer Coatings: Epoxy, VOC Compliant, Chemical and SolventResistantMIL-P-85582 Primer Coatings: Epoxy, VOC Compliant, Chemical and SolventResistantMIL-M-87929 Manuals, Technical: Operation and Maintenance Instruc

37、tions in WorkPackage Format (For USAF Equipment)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD- 1568B(USAF)28 February 19893STANDARDSMILITARYMIL-STD-454 Standard General Specifications for Electronic EquipmentMIL-STD-808 Finishes, Materials

38、and Processes for Corrosion Prevention Control inSupport EquipmentMIL-STD-883 Microelectronics, Test Methods and Procedures forMIL-STD-889 Dissimilar MetalsMIL-STD-1500 Cadmium-Titanium Plating, Low Embrittlement, ElectrodepositionMIL-STD-1530 Aircraft Structural Integrity Program, Airplane Requirem

39、entMIL-STD-1587 Materials and Process Requirements for Air Force Weapon SystemsMIL-STD-2073-1 DOD Material Procedures for the Development and Application ofPackaging Requirements (Part 1 of 2 Parts)(Unless otherwise indicated, copies of federal and military specifications, standards, andhandbooks ar

40、e available from the Naval Publications and Forms Center, (ATTN: NPODS), 5801Tabor Avenue, Philadelphia PA 19120-5099)2.1.2 Other Government documents, drawings, and publications.The following other Government documents, drawings, and publications form a part of thisdocument to the extent specified

41、herein. Unless otherwise specified, the issues are those citedin the solicitation.AFR 400-44 Corrosion Prevention and Control ProgramAFR 800-2 Acquisition Program ManagementT.O. 1-1-1 Cleaning of Aerospace EquipmentT.O. 1-1-2 Corrosion Prevention and Control for Aerospace EquipmentT.O. 1-1-4 Exterio

42、r Finishes, Insignia and Markings Applicable to USAFAircraftT.O. 1-1-8 Application of Organic Coatings, Aerospace EquipmentT.O. 1-1-689 Prevention and Control of Corrosion and Fungus inCommunication, Electronic Meteorological, and Avionic EquipmentFORMDD 1423 Contract Data Requirements List(Copies o

43、f AFRs and DD Forms 1423 are available from Air Force Publication DistributionCenter, 2800 Eastern Blvd, Baltimore MD 21220. Copies of Air Force Technical Orders areavailable from Oklahoma City Air Logistics Center, Tinker AFB OK 73145-5609.)2.2 Non-Government publications.The following documents fo

44、rm a part of this document to the extent specified herein. Unlessotherwise specified, the issues of documents which are DoD adopted are those listed in theissue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues ofdocuments not listed in the DoDISS are the issue of the d

45、ocuments cited in the solicitation.(See 6.2).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD- 1568B(SUAF)28 February 19894AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)ASTM G47 Determining Susceptibility to Stress-Corrosion Cracking of Hig

46、h-Strength 7XXXAluminum Alloy ProductsASTM G64 Resistance of Stress Corrosion Cracking of High Strength Aluminum Al loys,Classification ofASTM A380 Cleaning and Descaling Stainless Steel Parts, Equipment and Systems(Application for copies should be addressed to the American Society for Testing and M

47、aterials,1916 Race Street, Philadelphia PA 19103-1187.)AEROSPACE MATERIALS SPECIFICATIONS (AMS)AMS 3267 Sealing Compound, Low Adhesion, Corrosion Inhibiting, for Removable Panelsand Fuel Tank Inspection PlatesAMS 3374 Aircraft Firewall, Sealing Compound, One-part Silicone(Application for copies shou

48、ld be addressed to the Society of Automotive Engineers , 400Commonwealth Dr, Warrendale, PA 15096-0001.)(Non-Government standards and other publications are normally available from theorganizations that prepare or distribute the documents. These documents also may beavailable in or through libraries

49、 or through informational services.)2.3 Order of precedence.In the event of a conflict between the text of this document and the references cited herein, thetext of this document takes precedence. Nothing in this document, however, supersedesapplicable laws and regulations unless a specific exemption ha