AIR FORCE A-A-58068-1996 TRUCK LIFT FORK ELECTRIC SIT DOWN SOLID TIRES 6 000 POUND CAPACITY AT 24 INCH LOAD CENTER 180 INCH MINIMUM LIFT HEIGHT《在24英寸的负荷中心的180英寸最低扬程6000磅承受力固体轮胎电动降落.pdf

《AIR FORCE A-A-58068-1996 TRUCK LIFT FORK ELECTRIC SIT DOWN SOLID TIRES 6 000 POUND CAPACITY AT 24 INCH LOAD CENTER 180 INCH MINIMUM LIFT HEIGHT《在24英寸的负荷中心的180英寸最低扬程6000磅承受力固体轮胎电动降落.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE A-A-58068-1996 TRUCK LIFT FORK ELECTRIC SIT DOWN SOLID TIRES 6 000 POUND CAPACITY AT 24 INCH LOAD CENTER 180 INCH MINIMUM LIFT HEIGHT《在24英寸的负荷中心的180英寸最低扬程6000磅承受力固体轮胎电动降落.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、4 CH-POUND A-A-58068 28 June 96 COMMERCIAL lTEM DESCRIPTION TRUCK, LIFT, FORK, ELECTRIC, SIT DOWN, SOLID TIRES, 6,000 POUND CAPAClTY AT 24 INCH LOAD CENTER, 180 INCH MINIMUM LIFT HEIGHT The General SeMces Admhkmt on has authorized the use of this commercial item description , for aii federal agencie

2、s. 1. SCOPE. This commercial item description covers the general requirements for an electric, front wheel drive, rear wheel steer, sit down operator, solid tired, 6,000 pound at 24 inch load center capacity, forklift uck. It shall be Type EE, unless Othe- specified as Type E, in accordance with ANS

3、iAJL 583. It shail be capable of handiing cargo in and around warehouses, loading platforms, and docks; on paved or other hardsurfaces. 2. SALJENT CHARACTERISTICS. 2.1 Safety. The forklift shall comply with ASWANSI B56.1, ANSW 583, and OSHA standards in effect at the time of manufacture. A seatbelt

4、conforming to SAE 5386, and restraint devices designed to em the operators upper body remains entirely within the protection of the overhead guard in the event of tipover shaii be provided. Unless othemise specified in the contract, the final color shaii be yellow for safe operation in an indoor env

5、ironment. 2.2 Batte?!. The battery shail have adequate capacity to provide not less than 7.0 hours of continuous operation under normal inustrial use. The battery mounted half connector shall be the “SB“ type. 23 Hdraulic wstem(s). A pressure relief prokction device is required along with pump(s), c

6、ylinders, control valves, filter(s), reservoir, hoses, and ali other components necessary to make a complete hydraulic system(s). 2.4 Uihts and carriane. With no load on the forks, the seated operator shall be able to see at least one fork i at all iift heights and fork positions. 2.5 Fork msitioner

7、. The forks shall be capable of being laterally positioned manually without the need of tools. The fork spacing shaii be not more than 14 inches when the forks are at their most closed position, and not less than 40 inches when the forks are at their most spread position. These dimensions shall be m

8、easured to the outside edges of the forks. Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data which may improve this document should be sent to: WR-ALC/LVRE, 225 OCmulgee Court, Robins AFB GA 3 1088-1 647 AMSC NIA FSC 3930 DISTIUBUTION STATEMENT A. Approve

9、d for public release; distribution is unlimited Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5 8 Ob8. 9999974 0372067 988 M A-A-58068 2.6 m. Fork dimensions shail be 2.06 inches maximum thickness x 6.06 inches maximum width x 40.0 (+ or - 1 .O

10、) inches in length. 2.7 Side shift. Hydraulically powered fork side shifting shali be furnished. It shali be controlled by the seated operator, with at least 4.0 inches side shift each side of center (8.0 inches minimum total travel). 2.8 Load bac-. The load bacluest, in conjunction with the forks a

11、nd carriage, shall provide a verticai rear load guard at least 48 inches high, measured from the horizontal, load canying surfaces of the forks. 2.9 Steering. Power steering shail be furnished. 2.10 Service brakes. Service brakes conforming to ASWANSI B56.1 shaii be furnished. 2.1 1 park in brake. P

12、arking brake shall conform to ASWANSI B56.1. 2.12 Jndicators. The truck shall be equipped with a battery discharge indicator and an hour meter, both visible to the seated operator. 2.13 Controls. Ail controls shall be in accordance with ASWANSI B56.1. Ail load motion controls shall be seif centering

13、, that is they shail return to the neutral position when released. 2.14 External lights. There shall be at least two sealed beam, 25 watts minimum, fldghts. One shall be facing forward, mounted on the upright or overhead guard, and one mounted in the rear, hing rearward. 2.15 Taillight. One combinat

14、ion stoplight and taillight shall be installed. 2.1 6 m. The horn button shali be mounted in the center of the steering wheel. 2.17 erators overhead miard. The guard shall be in accordance with ASWANSI B56.1, includuig the falling-obect-protective-structure (FOPS) requirements. Overhead guard height

15、 from ground to top of guard shallbe 91 inches maximum. 2.1 8 Towing. A pin type towing device shall be recessed in the center rear of the truck. 2.19 Electromametic interference 0 sumression. The truck shail conml EMI to meet the requhments of SAE J551. 2.20 Painting. The frklift shall be primed an

16、d painted using standard commercial practices. Unless othenvise specified in the contract, the final color shail be yellow. AU stenciled words, symbols or other markings (for example “6000 POUND CAPACITY“ or “Lm HERE“), shaii be black. 2.21 Walkway coating. Floor plates and step surfaces shaii be co

17、ated with a non-slip coating compound or be furnished wih a non-slip metai surface. 222 Slinging provisions. Slinging devices that provide a means of attaching a shackle or ring to the forkiift for safe lifting sha be furnished to allow the truck to be lifted by a crane in its nod operating position

18、. Each device shall be not more than 1 .O inch thick. The opening in the device shail be at least 3.0 inches in diameter. Each siinging device, when loaded as the truck wili be picked up, shaii withstand a load of 2.3 thes the static load on each device. The wo& “LlF HERE“ shall be stenciled near ea

19、ch slinging device. If possible, the slinging devices may also be used as the tiedown devices (see paragraph 2.23). 2.23 Tiedown movisions. Tiedown devices shali be furnished that withstand the following loads: 3 .O times the unioaded truck weight in the forward and aft directions, 2.0 times the uni

20、oaded truck weight in the downward direction, and 1.5 times the unioaded truck weight in both lateral directions. Each device 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58068 shall withstand at least 1.5 times the loads in the previous sen

21、tence without breaking or rupturing. The &vices shall be not more than 1 .O inch thick, and the opening in the device shall be at least 3.0 inches in diameter. The word “TEDOWN“ shall be stenciled near each tiedown device. Ifpossible, the tiedown devices may ais0 be used as the slinging devices (see

22、 paragraph 2.22). 2.24 Performance. (1) Shall be capable of safely handiing a rated load of 6,000 pound, 48 inches per si& cube, with the center of gravily at the center of the cube. It shall be able to safely handie this rated load at all lift heights and fork side shift that the forklift is capabl

23、e of attaining. (2) Lifting speed. Shall be at least 18 feet per minute with rated load on the forks. (3) Lowering speed. Shail be not less than 27, nor more than 80 feet per minute, with rated load on the forks. (4) Right angle turn. With rated load on the forks and forklift positioned perpendicula

24、r to a wali, and with the front of the load against the wail, the truck shail be able to back up and make a complete right angle tum (ending up parallel to the wail) within 156 inches. (5) Travel speed. Shail be capable of traveling at least 5 miles per hour, in both forward and reverse directions,

25、while carrying rated load on the forks. (6) Slope ascension. With the truck facing up the slope and with rated load on the forks it shall be able to accelerate up a 15 percent (8.5 degrees) slope from a dead stop. (7) Upright tiit. With no load on the truck the upright (or mast) shail have at least

26、2.0 degrees forward tilt, and at least 6.0 degrees of rear tilt. (8) Upright height with forks on the ground (collapsed mast height). With no load on forks, the measurement from ground to uppermost projection of the upright assembly shall be not more than 91 inches. (9) Maximum fork lift height. Wit

27、h rated load on forks and forks horizontal, the forks shaii be capable of raisimg at least 180 inches, This shall be measured from ground to the horizontal, lifting surfaces of the forks, (1 O) Free lift height. With rated load on forks, and with the inner mast or carriage assembly just beginning to

28、 exceed the specified collapsed mast height, the distance from the ground to the top surfaces of the forks shall be not less than 53.0 inches. (1 1) Under clmce. With rated load on the forks and mast vertical, underclearance bemeen the ground and the mast shall be at least 2.75 inches. at maximum li

29、ft height for at least 10.0 minutes with not more than 2.00 inch of vertical drift, and not more than 1.5 degree of rotational drift. (1 2) Drift of load. With hydraulic fluid at nod operating temperatu, lift assembly shail hold rated load (13) Stability. The forklift shali meet the ASWANSI B56.1 “f

30、orward stacking“, “forward travei“, “iated stacking“, and “lateral travei“ stability requirements. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5 8 O b8 9999974 0372069 750 A-A-5 8068 t 2.25 An idencation plate made of a corrosion resistive

31、materiai shail be permanentiy instalied at an easily accessible location. It shaii contain the following infomatiox NOMENCLATURE MANFACTRERS NAME h“UFACT“SADDRESS MANUFACTURERS SERVICE TELEPHONE NUMBER MANUFACTURERS MODEL mER MA“SSERIALNUMBER DATE OF MANUFACTURE CONTRACT NUMBER NATIONAL STOCK NUMBER

32、 REGISTRATION NUMBER 2.26 Markings. AU stencils, decals, plates, etc. normally provided on the rnandactums standard forklift shaii be included. This shall include, as a minimum, the forklifts capacity in pounds, and ail information, Cautions and warnings normaiiy provided. 2.27 Tires. Tire loading s

33、hali not exceed those specifed in the Tire and Rim Association Yearbook. 3. REGULATORY REQUiREMJ3JTS. 3.1 The offerodcontractor is encouraged to use recovered materiais to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (Fm). However, used, r

34、ebuiit, or remanutkxmd components, pieces, and parts shall not be incorporated in the forklift. 4. QUMI“ ASSURANCE PROVISIONS. 4.1 product Conformance. The products provided shall confonn to the producers own drawings, specifcations, standards and quality assurance practices, and be the same product

35、 offered for de in the commerciai market. The Government reserves the right to quit proof of such conformance prior to first deiivery and thereafter as may be othemise provided for under the pro*ions of the contract. 42 Market Acceotability. he following market acceptability criteria are necessary t

36、o domment the quality of the product to be provided under this CID. 42.1 Commercial. The vehicle fmished shaii be, as of the date of award, the latest model (with minor modiftcations, as that term is defined in DoD FAR Supplement 252.21 1-7012, Paragraph K-85 of the solicitation) of an established p

37、roduct previously produced and sold in substantial commercial quantities exceeding the criteria at FAR 15.804-3(f)(2)(ii)(A) for at least three years. 422 The vehicle mished, or earlier models of it, absent &or modifications, shall have routinely been supported with spdrepair parts which were produc

38、ed or sold in the nod couse of business. 4.2.3 At the time of deiivery, the contractor shall fumish the Administrative Contracting Officer with verification of compliance with these requirements. 4.2.4 Offers shaii provide, as part of their proposais, the following information on the vehicle (or its

39、 earlier models) being offered as a commercial item: (1) Total sales to the U.S. Government or to contractors for U.S. Government use during the hree years. (2) Total sale of the item to the general public during the three years. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted

40、 without license from IHS-,-,- A-A-580b8 M 9999974 0272070 472 W A-A-5 8068 1 (3) hgth of time the item has been sold in the commercial market place. (4) other pertinent information necessary to determine that the item is an established commercial item. 5. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or oder. MLARY INTERESTS: CUSTODIAN: Air ForCe - 84 Army-AT Navy-SA PREPARING ACm AirForce84 AGENT-99 Project Number 3930-0683 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-