AIR FORCE A-A-58037-1994 GENERATOR PULSE《发电机 脉冲》.pdf

《AIR FORCE A-A-58037-1994 GENERATOR PULSE《发电机 脉冲》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE A-A-58037-1994 GENERATOR PULSE《发电机 脉冲》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-58037 M 9999974 0365530 174 I INCH-POUND 1 I I A-A-58037 October 28, 1994 COMMERCUL ITEM DESCRIPTION GENERA TOR, PULSE The General Services Administration has authorized the use of this Commercial Item Description ( CID ) for all agencies. 1. SCOPE This CID, describes a pulse generator with a de

2、lay range fiom O to 99.99 milliseconds. This CID is meant as a minimum requirement for the pulse generator in which only those manufacturers that meet or surpass the following requirements are qualified per this CID. 2. CLASSIFICATION Equipment covered by this CID may be commercially available equip

3、ment modified to the extent necessary to meet the following description. The equipment shall be Type III, Class 5, Style E and Color R in accordance with MIL-T-28800. 3. SALIENT CHARACTERISTICS 3.1 Design and construction. The equipment shall be UL (Underwriters Laboratories) listed and approved and

4、or shall comply with the Type III safety requirements of MIL-T-28800. 3.2 Electrical power sources . The equipment shall operate from nominal commercial, military and shipboard power sources of 115/230 volts AC (*lo%) at line frequencies of 50 to 60 Hz. Transient state conditions shall meet MIL-T-28

5、800 Class 5 requirements. Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data which may improve this document should be sent to: The Resources and Logistics Services Division, SA-ALCITILDD, Bldg. 171, Post C-12,485 Quentin Roosevelt Rd., Kelly AFB, TX 78241

6、 -6524. AMSC N/A FSC 6625 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58037 W 9999974 0365533 O00 W A-A-58037 3.3 Temperature requirements. (a) Operating temper

7、ature. The equipment shall meet its performance and accuracy requirements in an operating environment of +5“c to +55“c. (b) Non-operating temperature. The equipment shall meet its performance and accuracy requirements in a non-operating environment of 0C to +60C. 3.4 Mean time between failures (MTBF

8、). The equipment MTBF shall be 2,000 hours. The lower test MTBF shall be 2,000 hours and the upper test MTBF shall be 4,000 hours. 3.5 Pre-conditioning requirement. Each deliverable equipment shall be capable of being subjected to the environmental screening effects of burn-in and thermal cycling, w

9、ith thermal cycling being accomplished in the sample testing phase. 3.6 Calibration and maintenance adjustments. The design of the system shall provide for readily accessible calibration adjustments and maintenance adjustments. These adjustments shall be provided by variable value components which a

10、re adjustable by the use of simple means. The calibration by substitution of selected components or parts is unacceptable unless specifically approved. The calibration adjustments, wherever possible, shall be accessible without removal of the instrument case or modules. The calibration interval shal

11、l be a period of one year or greater based on an operating time of 2,000 hours. 3.7 Performance characteristics. (a)Pulse delay (1)Delav range. The delay range of the generator shall be from O to 99.99 milliseconds (ms), selectable in 1 nanoseconds (ns) increments. (2)Delay accuracy. The minimum del

12、ay accuracy shall be k (1 ns + time setting x time base stability). (b)Pulse width (1)Pulse width rance. The pulse width range of the generator shall be from 5 to 9.99 ms, selectable in 1 nanoseconds increments. (2)Pulse width accu racy. The minimum pulse width accuracy shall be I1 ns plus time base

13、 stability). (c)Time base stability (1)Long term. The long term stability shall be better than 3xiO-/day 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58037 (2)Temperature. The temperature stability shall be better than 1x1 O-*OC. (d)Inserion

14、 delay. A delay between an external trigger and an initial pulse shall not exceed 150 ns. (e)m. A jitter between an external trigger or an initial delay and the output pulse shall not exceed 250 picoseconds rms. (f)Trina. The trigger modes shall be manual, internal and external and be front panel se

15、lectable. (g)F,xternal trim. The pulse generator shall start to trigger when an input pulse, which has a minimum amplitude of 200 millivolts or less and a minimum pulse width of 1 O ns or less, is applied. The trigger shall be -2 to +2 volts, and have a positive, negative slope selection switch. (h)

16、kpetition rate. The maximum repetition rate of the pulse generator shall be at least 5 MHz. (i)bitial and de lay pulse ou ut. The pulse generator output shall be 5 volts into 50 ohms; the rise and fall time shall be less than 5 ns; selectable complements. (i)Internal clock modes . The clock shall op

17、erate from an internal oscillator that has a frequency of 5 or 10 KHz. (k)Remote operation. The generator shall be capable of remote operation with IEEE 488 interface bus. All front panel functions and controls except power, manual trigger and polarity shall be able to be initiated remotely via IEEE

18、 488 bus. 4. REGULATORY REQUIREMENTS In accordance with Section 23.403 of the Federal Acquisition Regulations, the Governments policy is to acquire items composed of the highest percentage of recovered materials practicable, consistent with maintaining a satisfactory level of competition without adv

19、ersely affecting performance requirements or exposing the suppliers employees to undue hazards from the recovered materials. 5. PACKAGING AND MARKING The items shall be packed in accordance with normal commercial practice and packed to assure acceptance by common carrier and provide product protecti

20、on against loss and damage during multiple shipments, handling, and storage. The shipping shall be in compliance with national motor fi-eight classification and uniform freight classification. Shipping container shall be marked as specified in the contract or order. 3 Provided by IHSNot for ResaleNo

21、 reproduction or networking permitted without license from IHS-,-,-A-A-58037 H YYqYT74 036.5533 963 A-A-58037 , 6. QUALITY ASSURANCE Certification. The contractor shall cedi and maintain substantiating evidence that the product offered meets the salient characteristics of this CID, and that the prod

22、uct conforms to the producers own drawings, specifications, standards and quality assurance practices. The Government reserves the right to require proof of such conformance prior to first delivery, and thereafter, as may be otherwise provided for under the provisions of the contract. Small business

23、es that cannot offer products with established commercial market acceptability, may compete by submission of bid samples. (The Government reserves the rights to require proof of such conformance before first delivery and thereafter as may be otherwise provided for under the provisions of the contrac

24、t). 7. NOTES Metric products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided they fall within specified tolerances using conversion tables contained in the latest revision of Federal Standard No. 376, and all o

25、ther requirements of this CID are met. Federal and Military specifications are available from the Defense Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 191 11-5094. Known acceptab le products. The following products are known to have previously met the Salient Characteristi

26、cs of this CID and need not resubmit bid samples or certification. All other manufacturers must meet the requirements of this CID and submit to bid testing and certification. -. ._ - I- Manufacturer Model Berkeley Nucleonic Corp. 7085 Hewlett Packard 5359A MILITARY INTERESTS: custo Air Force - 99 Preparing activity: Air Force - 82 (Project No. 6625-0805) Reviewine Acti vites: Navy - AS DLA - ES 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-