AECMA PREN 3367-1988 Aerospace Series Steel FE-PL10 Hardened Tempered and Cold Drawn 1260 Less Than or Equal to Rm Less Than or Equal to 2790 MPa Wire for Spring 0 20 Less Than or P.pdf

《AECMA PREN 3367-1988 Aerospace Series Steel FE-PL10 Hardened Tempered and Cold Drawn 1260 Less Than or Equal to Rm Less Than or Equal to 2790 MPa Wire for Spring 0 20 Less Than or P.pdf》由会员分享，可在线阅读，更多相关《AECMA PREN 3367-1988 Aerospace Series Steel FE-PL10 Hardened Tempered and Cold Drawn 1260 Less Than or Equal to Rm Less Than or Equal to 2790 MPa Wire for Spring 0 20 Less Than or P.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、A. E C. M. A. STAN DAR D NORME A.E.C=M.A. A.E,C.M.A. NORM Edition approved far publication 31 March 1988 prEN 3367 Issue P I March 1988 Comments should be sent within six months C5 Chairman J. ODORICO after the date of publication decision A.E.C.M.A. 88, Bd. Malesherbes 75008 PARIS - FRANCE UDC : Ke

2、y words : DIT PAR LASSOCIATION EUROPENNE DES CONSTRUCTEURS DE MATRIEL AEROSPATIAL 88, boulevard Malesherbes, 75008 PARIS -TL. 45-63-82-85 ENGLLSH VERSION Aerospace series Steel FE-PLI O I .ardened, tempered and CGJ Gawn 1260 EN 2600, Aerospace series - Designation of metallic semi-finished products

3、- Rules 1). i) in preparation Previous page is blank Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN3367 BA W 1012311 0005587 b W prEN 3367

4、Page 4 a O c I si Mn P S Fe Element Chemical I Composition max. 1 0,65 0,lO 0,30 - - 0,95 0,35 0,ao 0,020 0.025 . Rem. L Air melted Method of melting Form Method of production Llmlt dimensions 5.1 Technical speclficatlon Drawn wire 0,ZO i D i 10,50 mm - EN 2069-5 5.2 Dlmensional standard EN 2369 5.3

5、 Dimensional standard code 6.1 Condltion and Hardened tempered and cold drawn Hardened 890 5 0 3 910C / OQ + tempered 520 4 mn (check by microhardness HV) D in nrn 0,20 D 0,30 0,30 D 7 0,40 0.40 D 0.50 0;50 5 O 0;60 0,60 D 0,7D 0,10 D 10,O 0.80 D 0,90 Rm (MPa) 2500/2790 2450/2740 2400/2700 2350/2650

6、 2300/2600 2250/2500 t 2250/2500 Oi90 D li10 2200/2450 1,lO D 1,30 2160/2400 1,30 D 1,50 2110/2350 1,50 D 5 1,70 2060/2300 1.70 D 1,90 2010/2200 li90 D 5 2i20 I 1960/2160 Table 1 Tensile strength D in mm 2,20 D 2,50 2.50 O i 2,80 2,80 D 3,lO 3,lO 0 3,40 3,40 D I3,70 3,70 D 4,OO 4,OO D 14,40 4,40 D 4

7、,80 4,80 D 15,20 5,20 D 5 5,60 5,60 D 6,50 6,50 D 5 10,50 Rm (MPa) 1910/2110 1860/2060 1810/2010 1760/1960 17201 1910 1670/1860 1620/1810 1570/1760 1520/1720 1470/ 16 70 1410/1620 1260/1420 The rules governing the designation of semi-finished products are indicated in standard EN 2600, When the codi

8、fied designation is used, the identification code shall be as follows : 1EN 33671iU1XXll- Material standard number I 11 I /Letter code (see 6.2) 1 I l Appropriate dimensional standard code (see 5.3) Data concerning dimension (see EN 2600) Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-