ABS 180-2018 RULES FOR BUILDING AND CLASSING OFFSHORE SUPPORT VESSELS 2018.pdf

《ABS 180-2018 RULES FOR BUILDING AND CLASSING OFFSHORE SUPPORT VESSELS 2018.pdf》由会员分享，可在线阅读，更多相关《ABS 180-2018 RULES FOR BUILDING AND CLASSING OFFSHORE SUPPORT VESSELS 2018.pdf（1391页珍藏版）》请在麦多课文档分享上搜索。

1、 Notices and General Information RULES FOR BUILDING AND CLASSING OFFSHORE SUPPORT VESSELS 2018 NOTICES AND GENERAL INFORMATION American Bureau of Shipping Incorporated by Act of Legislature of the State of New York 1862 2017 American Bureau of Shipping. All rights reserved. ABS Plaza 16855 Northchas

2、e Drive Houston, TX 77060 USA Table of Contents N&GI Notices and General Information CONTENTS Introduction . 1 TABLE 1 Applicable Editions of Booklets Comprising 2018 Rules 2 TABLE 2 Division and Numbering of Rules 3 Rule Change Notice (2018) . 4 TABLE 3 Summary of Changes from the 2017 Rules 4 ii A

3、BSRULES FOR BUILDING AND CLASSING OFFSHORE SUPPORT VESSELS .2018 Notices and General Information Introduction 1. The year 2018 edition of the Rules for Building and Classing Offshore Support Vessels consists of the nine (9) booklets as shown in Table 1. In this regard, we would bring the following t

4、o the users attention: a) The purpose of the generic title ABS Rules for Conditions of Classification (Part 1) is to reflect the expanded contents of PART 1, as a result of including consolidated requirements for “Classification” applicable to all types of and sizes of vessels, barges and specific s

5、hipboard arrangements/systems, etc., except for those in offshore service, as specified in the Foreword to Part 1. Additional specific requirements are contained in Part 1 of these Rules for Building and Classing Offshore Support Vessels. b) The purpose of the generic title ABS Rules for Materials a

6、nd Welding of PART 2 is to emphasize the common applicability of the requirements to ABS-classed vessels, other marine structures and their associated machinery, and thereby make PART 2 more readily a common “PART” of various ABS Rules and Guides, as appropriate. c) The purpose of the generic title

7、ABS Rules for Survey After Construction (Part 7) is to reflect the expanded contents of PART 7, as a result of including consolidated requirements for “Surveys After Construction” applicable to all types and sizes of vessels, barges and specific shipboard arrangements/systems, etc., as specified in

8、Part 7, Chapter 1, Section 1. 2. The numbering system applied in the Rules is shown in Table 2. 3. The primary changes from the 2017 Rules are identified and listed in Table 3. The effective date of the indicated Rule Changes is 1 January 2018, unless specifically indicated otherwise. 4. The effecti

9、ve date of each technical change since 1993 is shown in parenthesis at the end of the subsection/paragraph titles within the text of each Part. Unless a particular date and month are shown, the years in parentheses refer to the following effective dates: (2000) and after 1 January 2000 (and subseque

10、nt years) (1996) 9 May 1996 (1999) 12 May 1999 (1995) 15 May 1995 (1998) 13 May 1998 (1994) 9 May 1994 (1997) 19 May 1997 (1993) 11 May 1993 5. Until the next edition of the Rules for Building and Classing Offshore Support Vessels is published, Change Notices and/or Corrigenda, as necessary, will be

11、 published on the ABS website www.eagle.org only, and will be available free for downloading. The consolidated edition of the Rules for Building and Classing Offshore Support Vessels, which includes Change Notices and/or Corrigenda using different colors for easy recognition, will be published on th

12、e ABS website only when RCN and/or Corrigenda are issued. 6. The listing of CLASSIFICATION SYMBOLS AND NOTATIONS is available from the ABS website www.eagle.org for download. ABSRULES FOR BUILDING AND CLASSING OFFSHORE SUPPORT VESSELS .2018 1 Notices and General Information TABLE 1 Applicable Editio

13、ns of Booklets Comprising 2018 Rules Notices and General Information 2018 Part 1: Rules for Conditions of Classification (1)2018 (2)Part 1: Conditions of Classification (Supplement to the ABS Rules for Conditions of Classification) (1)2018 Part 2: Rules for Materials and Welding Rules for Testing an

14、d Certification of Materials Rules for Welding and Fabrication 2018 (2)Part 2: Rules for Materials and Welding Aluminum and Fiber Reinforced Plastics (FRP) 2018 (2)Part 3: Hull Construction and Equipment 2018 Part 4: Vessel Systems and Machinery 2018 Part 5: Specialized Vessels and Services Chapter

15、1 Vessels Intended for Offshore Support Services Chapter 2 Offshore Supply Chapter 3 Anchor Handling and Towing Chapter 4 Fire Fighting Chapter 5 Diving and Remotely Operated Vehicles (ROVs) Support Chapter 6 Oil Spill Recovery Chapter 7 Safety Standby Service Rescue Chapter 8 Pipe Laying Chapter 9

16、Heavy Lift Chapter 10 Well Intervention Chapter 11 Well Stimulation Chapter 12 Well Test Chapter 13 Escort Chapter 14 Wind Turbine Installation, Maintenance and Repair (Wind IMR) Chapter 15 Cable Laying 2018 Part 7: Rules for Survey After Construction 2018 (2)Notes: 1 The requirements for conditions

17、 of classification are contained in the separate, generic ABS Rules for Conditions of Classification (Part 1). Additional specific requirements are contained in Part 1 of these Rules. 2 The latest edition of these Rules is to be referred to. These Rules may be downloaded from the ABS website at www.

18、eagle.org, Rules and Guides, Downloads or may be ordered separately from the ABS Publications online catalog at www.eagle.org, Rules and Guides, Catalog. 2 ABSRULES FOR BUILDING AND CLASSING OFFSHORE SUPPORT VESSELS .2018 Notices and General Information TABLE 2 Division and Numbering of Rules Divisi

19、on Number Part Part 1 Chapter Part 1, Chapter 1 Section Section 1-1-1 Subsection (see Note 1) 1-1-1/1 Paragraph (see Note 1) 1-1-1/1.1 Subparagraph 1-1-1/1.1.1 Item 1-1-1/1.1.1(a) Subitem 1-1-1/1.1.1(a)i) Appendix Appendix 1-1-A1 or Appendix 1-A1-1 Note: 1 An odd number (1, 3, 5, etc.) numbering sys

20、tem is used for the Rules. The purpose is to permit future insertions of even-numbered paragraphs (2, 4, 6, etc.) of text and to avoid the necessity of having to renumber the existing text and associated cross-references, as applicable, within the Rules and associated process instructions, check she

21、ets, etc. ABSRULES FOR BUILDING AND CLASSING OFFSHORE SUPPORT VESSELS .2018 3 Notices and General Information Rule Change Notice (2018) TABLE 3 Summary of Changes from the 2017 Rules EFFECTIVE DATE 1 July 2017 shown as (1 July 2017) (based on the contract date for new construction between builder an

22、d Owner) Part/Para. No. Title/Subject Status/Remarks PART 3 Hull Construction and Equipment 3-2-14/17.1 Strength To reflect current practice for cover plates and address vortex shedding for spade rudders with embedded trunks. (Incorporates Notice No. 1) 3-2-14/Figure 5 (New) To reflect current pract

23、ice for cover plates and address vortex shedding for spade rudders with embedded trunks. (Incorporates Notice No. 1) 3-2-14/Figure 6 (New) To reflect current practice for cover plates and address vortex shedding for spade rudders with embedded trunks. (Incorporates Notice No. 1) 3-2-14/Figure 7 (New

24、) To reflect current practice for cover plates and address vortex shedding for spade rudders with embedded trunks. (Incorporates Notice No. 1) 3-2-14/17.1.2 In way of Cutouts To reflect current practice for cover plates and address vortex shedding for spade rudders with embedded trunks. (Incorporate

25、s Notice No. 1) PART 4 Vessel Systems and Machinery 4-2-1/13.9.2iv) To include the alternative of normal continuous cruise power, in line with IACS UR M51 Rev.4, Feb. 2015. (Incorporates Notice No. 1) 4-2-1/Table 1 Required Material and Nondestructive Tests of Diesel Engine Parts To clarify the scop

26、e of hydraulic testing for high pressure fuel injection pipes including common fuel rail and high pressure common servo oil systems, in line with IACS UR M72 rev. 1 Mar. 2016. (Incorporates Notice No. 1) 4-2-1/Table 2 Test Pressures for Parts of Internal-combustion Engines To clarify the scope of hy

27、draulic testing for high pressure fuel injection pipes including common fuel rail and high pressure common servo oil systems, in line with IACS UR M72 rev. 1 Mar. 2016. (Incorporates Notice No. 1) 4-2-2/1.1 Application To clarify the categorization of turbochargers and the application of Type Approv

28、al. (Incorporates Notice No. 1) 4-2-2/1.3.1 Turbocharger To clarify the categorization of turbochargers and the application of Type Approval. (Incorporates Notice No. 1) 4-2-2/1.3.3 (New) Generic Range To clarify the categorization of turbochargers and the application of Type Approval. (Incorporates

29、 Notice No. 1) 4-2-2/1.5.1ii) To clarify the categorization of turbochargers and the application of Type Approval. (Incorporates Notice No. 1) 4-2-2/3.3 Category A and B Turbochargers To clarify the categorization of turbochargers and the application of Type Approval. (Incorporates Notice No. 1) 4-2

30、-2/3.5 Category C Turbochargers To clarify the categorization of turbochargers and the application of Type Approval. (Incorporates Notice No. 1) 4-2-2/3.7.3 Certification Under Quality Assurance Assessment PQA (IACS UR Z26 Alternative Certification Scheme) To clarify the categorization of turbocharg

31、ers and the application of Type Approval. (Incorporates Notice No. 1) 4-2-2/5.1 General To clarify the categorization of turbochargers and the application of Type Approval. (Incorporates Notice No. 1) 4-2-2/5.3 Containment To clarify the categorization of turbochargers and the application of Type Ap

32、proval. (Incorporates Notice No. 1) 4-2-2/5.7 Type Testing (applicable to category B and C turbochargers) To clarify the categorization of turbochargers and the application of Type Approval. (Incorporates Notice No. 1) 4 ABSRULES FOR BUILDING AND CLASSING OFFSHORE SUPPORT VESSELS .2018 Notices and G

33、eneral Information Part/Para. No. Title/Subject Status/Remarks 4-2-2/7 Piping Systems for Turbochargers To clarify the categorization of turbochargers and the application of Type Approval. (Incorporates Notice No. 1) 4-2-2/8 (New) Alarms and Monitoring To clarify the categorization of turbochargers

34、and the application of Type Approval. (Incorporates Notice No. 1) 4-2-2/11.1 Shop Inspection and Tests To clarify the categorization of turbochargers and the application of Type Approval. (Incorporates Notice No. 1) 4-2-2/11.1.1 Material Tests To clarify the categorization of turbochargers and the a

35、pplication of Type Approval. (Incorporates Notice No. 1) 4-2-2/11.1.5 Shop Trial To clarify the categorization of turbochargers and the application of Type Approval. (Incorporates Notice No. 1) 4-2-2/11.3 Certification of Turbochargers To clarify the categorization of turbochargers and the applicati

36、on of Type Approval. (Incorporates Notice No. 1) 4-3-4/13.1.9 (New) System Response Under Failure To detect failure in the steering gear control system and provide the operator with sufficient information to decide what action is required for the different failure scenarios, in line with IACS UR E25

37、 June 2016. (Incorporates Notice No. 1) 4-3-4/Table 1 Steering Gear Instrumentation To detect failure in the steering gear control system and provide the operator with sufficient information to decide what action is required for the different failure scenarios and to require a deviation alarm in add

38、ition to basic failure detection, in line with IACS UR E25 June 2016. (Incorporates Notice No. 1) 4-3-5/1.1 Application To clarify the various terms used for steering systems and their associated equipment, in line with IACS UI SC242 Rev.1, Apr. 2016. (Incorporates Notice No. 1) 4-3-5/1.5.6 (New) St

39、eering System To clarify the various terms used for steering systems and their associated equipment, in line with IACS UI SC242 Rev.1, Apr. 2016. (Incorporates Notice No. 1) 4-3-5/5.12.2(b)iii) To clarify that the capacity requirements apply regardless whether he steering systems are arranged with c

40、ommon or dedicated power units that the requirements of 4-3-4/11.1 apply to each steering system in ships fitted with multiple steering systems, in line with IACS UI SC242 Rev.1, Apr. 2016. (Incorporates Notice No. 1) 4-3-5/5.12.4 (New) Electric and Electrohydraulic Steering Systems To clarify that

41、the capacity requirements apply regardless whether he steering systems are arranged with common or dedicated power units that the requirements of 4-3-4/11.1 apply to each steering system in ships fitted with multiple steering systems, in line with IACS UI SC242 Rev.1, Apr. 2016. (Incorporates Notice

42、 No. 1) 4-3-5/7.5 (New) Failure Detection and Response To detect failure in the steering gear control system and provide the operator with sufficient information to decide what action is required for the different failure scenarios, in line with IACS UR E25 June 2016. (Incorporates Notice No. 1) 4-3

43、-8/15.11 Instrumentation To detect failure in the steering gear control system and provide the operator with sufficient information to decide what action is required for the different failure scenarios, in line with IACS UR E25 June 2016. (Incorporates Notice No. 1) 4-6-2/5.7.3(c) Fire Resistance To

44、 clarify the cases in which flexible hoses need not be of fire-resistant type. (Incorporates Notice No. 1) 4-6-2/5.9.1(c) (Deleted) Operational Conditions To minimize the use of slip-on joints for pipe connection except for cases where compensation of axial pipe deformation is necessary and to clari

45、fy the requirements, in line with IACS UR P2 Rev.2, Mar. 2016. (Incorporates Notice No. 1) 4-6-2/5.9.1(g) Slip-on Joints To minimize the use of slip-on joints for pipe connection except for cases where compensation of axial pipe deformation is necessary and to clarify the requirements, in line with

46、IACS UR P2 Rev.2, Mar. 2016. (Incorporates Notice No. 1) ABSRULES FOR BUILDING AND CLASSING OFFSHORE SUPPORT VESSELS .2018 5 Notices and General Information Part/Para. No. Title/Subject Status/Remarks 4-6-2/5.9.1(h) Application To clarify the requirements, in line with IACS UR P2 Rev.2, Mar. 2016. (

47、Incorporates Notice No. 1) 4-6-2/Table 9 Examples of Mechanical Joints To update the figures for “Machine Grooved Type” and “Slip Type” slip-on joints, in line with IACS UR P2 Rev.2, Mar. 2016. (Incorporates Notice No. 1) 4-6-2/Table 10 Application of Mechanical Joints To clarify the restrictions fo

48、r on slip-on joints and flexible hoses used for L.O. lines and other flammable oils, and installed on open decks, in line with IACS UR P2 Rev.2, Mar. 2016. (Incorporates Notice No. 1) 4-8-2/7.21 Harmonics To specify that the harmonic distortion calculation report is to be kept on board for exception

49、s to the 8% limit in cases where all installed equipment and systems have been designed for higher THD levels, in line with IACS UR E24 June 2016. (Incorporates Notice No. 1) 4-8-2/9.22 (New) Harmonic Distortion for Ship Electrical Distribution System including Harmonic Filters To introduce requirements for survey of harmonic filters and harmonic distortion levels, in line with IACS UR E24 June 2016. (Incorporates Notice No. 1) 4-8-2/9.23 Protection of Harmonic Filter Circuits Associated with Electric Propulsion To introduce requirements for survey of harmonic filters and harmonic d