A-A-59435-1999 HEATERS GUN TYPE ELECTRIC [Superseded DLA MIL-H-45193 D CANC NOTICE 1 DLA MIL-H-45193 D (1) DLA MIL-H-45193 D DLA MIL-H-45193 C (1) DLA MIL-H-45193 C DLA MIL-H-45193.pdf

《A-A-59435-1999 HEATERS GUN TYPE ELECTRIC [Superseded DLA MIL-H-45193 D CANC NOTICE 1 DLA MIL-H-45193 D (1) DLA MIL-H-45193 D DLA MIL-H-45193 C (1) DLA MIL-H-45193 C DLA MIL-H-45193.pdf》由会员分享，可在线阅读，更多相关《A-A-59435-1999 HEATERS GUN TYPE ELECTRIC [Superseded DLA MIL-H-45193 D CANC NOTICE 1 DLA MIL-H-45193 D (1) DLA MIL-H-45193 D DLA MIL-H-45193 C (1) DLA MIL-H-45193 C DLA MIL-H-45193.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUNDA-A-5943527 August 1999SUPERSEDINGMIL-H-45193D17 January 1985MIL-H-45193D(1)9 January 1986COMMERCIAL ITEM DESCRIPTIONHEATERS, GUN TYPE, ELECTRICThe General Services Administration has authorized the use of this Commercial Item Description (CID) forall federal agencies.1. SCOPE. This CID co

2、vers the general requirements for electric heater guns. Typically the guns areused to thaw or dry out equipment or to shrink insulating tubing associated with electrical applications.2. CLASSIFICATION. The heater guns shall conform to the following characteristics:2.1 Type. The heater guns shall mee

3、t the temperature range requirements of table 1 with an air flowvolume of 20 cubic feet per minute.Table I. Characteristics.Type123Heat RangeDegreesFahrenheit G0125G02 F350 to 500 F 500 to 750 F 750 to 1000 FBeneficial comments, recommendations, additions, deletions, clarifications, etc. and any dat

4、a whichmay improve this document should be sent to: Defense Supply Center Columbus, ATTN: DSCC-VAI,3990 East Broad Street, Columbus, Ohio 43216-5000.FSC 4940Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5943523. SALIENT CHARACTERISTICS.3.1 Cons

5、truction. The heater guns shall conform to the standards of Underwriters Laboratoryspecification E47277, Electric Heating Applications; and NFPA70, the National Electric Code.3.1.1 Mechanical Properties.3.1.2 Function Switch. The guns shall be provide with a three-position switch. The positions of t

6、he switchshall be in the following sequence: ON FAN HEAT and shall be labeled as such. If the switch is springloaded, provision will be made for locking the switch in the selected position.3.1.3 Power Cord. Each gun shall be furnished with a power cord of not less than six feet. The powercord shall

7、be made in accordance with NFPA-70 and shall have a 3 prong plug.3.1.4 Voltage. The guns shall operate on single phase, alternating current of 120 volts AC at 60 Hertz.3.1.5 Accessories. Each gun shall be provided with a stand that permits the heated air stream to bedirected over a 90-degree arc. Ea

8、ch gun shall be provided with two heat reflectors used for heatshrinkable tubing. The reflectors shall provide for the even distribution of heat over at least 1.5 inches oflength. One reflector will be for tubing up to .75 inch diameter and the second for tubing over .75 inch toat least two-inch dia

9、meter.3.1.6 Heat Regulation. Each gun shall be equipped with a air regulating system that will control thedischarge air temperature within the range for the particular model of gun.3.1.7 Dimensions and Tolerances. The guns shall not exceed 16 inches in length, 6 inches in deep and12 inches in height

10、. The weight of the guns shall not exceed 4 pounds with the stand attached and shallbe suitable for single hand operation.3.1.8 Marking. Each gun shall be marked per the manufacturers standard procedure with themanufacturers name and part and or model number.3.2 Finish. The manufacturers standard co

11、mmercial finish shall be suitable for the heater guns.3.3 Workmanship. The heater guns shall be free from sharp edges, and constructed with the bestcommercial practice available within the heater gun industry.4. REGULATORY REQUIREMENTS.4.1 Recovered Materials. This offeror/contractor is encouraged t

12、o use recovered materials to themaximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation(FAR).5. QUALITY ASSURANCE PROVISIONS.5.1 Product Conformance. The products provided shall meet the salient characteristics of this CID,conform to the producers own dr

13、awings, specifications, standards and quality assurance practices, andbe the same product offered for sale in the commercial market. The Government reserves the right torequire proof of such conformance.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,

14、-A-A-5943535.2 Market Acceptability. The following market acceptability criteria are necessary to document thequality of the product to be provided under the requirements of this CID.a. The company producing the item must have been producing a product meeting therequirements of this CID, for at leas

15、t five years.b. The company must have sold 1,000 units meeting this CID, in the commercial marketplace orto the Government, over the past two years.6. PACKAGING.6.1 Preservation, Packing and Marking. Preservation, packing, and marking shall be as specified in thecontract or order.7. NOTES.7.1 Part I

16、dentification Number (PIN). The following Part Identification Number procedure is forgovernment purposes and does not constitute a requirement for the contractor. This example describes apart numbering system for CID A-A-XXXXX. See table II for corresponding CID dash numbers and thetype of heater gu

17、ns.AA59435 G03 001CID Number Dash Number(see table II)7.2 Ordering Data. The contract or order should specify the following:a. CID document number, revision, and CID PINb. Quality assurance provisionsc. Preservation, packing and marking as required. (see 5.1)7.3 National Stock Numbers (NSNs). The NS

18、Ns listed in table II correspond to this CID.Table II. National Stock Number / CID Cross Reference.NSN CAGE Model Heat Range o F CID Dash #4940-00-357-1369 59164 EP-3 300 to 500 0014940-00-357-1369 83284 HG-301A 300 to 500 0024940-00-785-1162 59164 EP-3 300 to 500 0034940-00-785-1162 83284 HG-301A 3

19、00 to 500 0044940-00-314-9789 59164 EP-3 300 to 500 0054940-00-561-1002 59164 EP-5 500 to 750 0064940-00-364-2828 59164 EP-5 500 to 750 0074940-01-028-7493 59164 EP-5 500 to 750 0084940-000438-1606 59164 EP-7 750 to 1000 0094940-00-986-5899 59164 EP-7 750 to 1000 0104940-01-391-7046 59164 EP-7 750 t

20、o 1000 0117.4 Intended Use. The electric heater guns for thawing or drying operations requiring a stream of air orheated air. The heater gun can be used on heat shrinkable products used in electrical or electronic wiringwhich require a stream of air or heater air.Provided by IHSNot for ResaleNo repr

21、oduction or networking permitted without license from IHS-,-,-A-A-5943547.5 Sources of Supply. The following is a list of suppliers that have provided heater guns meeting therequirements of this CID to the Government in the past. This is not an all-inclusive list or an endorsementof any of the liste

22、d suppliers.SUGGESTED SOUCES OF SUPPLYManufacturersCAGE name and address59164 Eddy Products1509 Rapids Dr.Racine, WI 53404-2333(414) 633-234465309 Steinel America Inc.9051 Lyndale Ave. SouthMinneapolis, MN 55420(813) 646-325383284 Master Appliance Corp.2420 18thSt.Racine, WI 53401(414) 633-77917.6 G

23、overnment Users. To acquire information on obtaining the heater guns from the Governmentinventory system, contact Defense Supply Center, Columbus, ATTN: DSCC, P.O. Box 3990, Columbus,OH 43216, or telephone (614) 692-7884.7.7 UL standards are available from the Underwritten Laboratories, Inc., 333 Pf

24、ingston Road, Northbrook,IL, 60062.7.8 NFPA standards are available from the National Fire Protection Associators, Batterymarch Park,Quincy, MA, 02269-9101.Military Interests: Civil Agency Coordinating Activity:GSA - FSSCustodians: Preparing activity:Air Force 99 DLA - CCDLA CCReview activity:Air Force - 82(Project 4940-0724-01)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-