API SPEC 11D1-2009 Packers and Bridge Plugs (Second Edition Effective January 1 2010)《封隔器和桥塞.第2版.生效日期 2010年1月》.pdf

《API SPEC 11D1-2009 Packers and Bridge Plugs (Second Edition Effective January 1 2010)《封隔器和桥塞.第2版.生效日期 2010年1月》.pdf》由会员分享，可在线阅读，更多相关《API SPEC 11D1-2009 Packers and Bridge Plugs (Second Edition Effective January 1 2010)《封隔器和桥塞.第2版.生效日期 2010年1月》.pdf（42页珍藏版）》请在麦多课文档分享上搜索。

1、Packers and Bridge PlugsANSI/API SPECIFICATION 11D1 SECOND EDITION, JULY 2009EFFECTIVE DATE: JANUARY 1, 2010CONTAINS API MONOGRAM ANNEX AS PART OF U.S. NATIONAL ADOPTIONISO 14310:2008 (Identical), Petroleum and natural gas industriesDownhole equipmentPackers and bridge plugsPackers and Bridge PlugsU

2、PSTREAM SEGMENT ANSI/API SPECIFICATION 11D1SECOND EDITION, JULY 2009EFFECTIVE DATE: JANUARY 1, 2010CONTAINS API MONOGRAM ANNEX AS PART OF U.S. NATIONAL ADOPTIONISO 14310:2008 (Identical), Petroleum and natural gas industriesDownhole equipmentPackers and bridge plugsSpecial NotesAPI publications nece

3、ssarily address problems of a general nature. With respect to particular circumstances, local, state, and federal laws and regulations should be reviewed.Neither API nor any of APIs employees, subcontractors, consultants, committees, or other assignees make any warranty or representation, either exp

4、ress or implied, with respect to the accuracy, completeness, or usefulness of the information contained herein, or assume any liability or responsibility for any use, or the results of such use, of any information or process disclosed in this publication. Neither API nor any of APIs employees, subco

5、ntractors, consultants, or other assignees represent that use of this publication would not infringe upon privately owned rights.Users of this recommended practice should not rely exclusively on the information contained in this document. Sound business, scientific, engineering, and safety judgment

6、should be used in employing the information contained herein. API publications may be used by anyone desiring to do so. Every effort has been made by the Institute to assure the accuracy and reliability of the data contained in them; however, the Institute makes no representation, warranty, or guara

7、ntee in connection with this publication and hereby expressly disclaims any liability or responsibility for loss or damage resulting from its use or for the violation of any authorities having jurisdiction with which this publication may conflict.API publications are published to facilitate the broa

8、d availability of proven, sound engineering and operating practices. These publications are not intended to obviate the need for applying sound engineering judgment regarding when and where these publications should be utilized. The formulation and publication of API publications is not intended in

9、any way to inhibit anyone from using any other practices.Any manufacturer marking equipment or materials in conformance with the marking requirements of an API standard is solely responsible for complying with all the applicable requirements of that standard. API does not represent, warrant, or guar

10、antee that such products do in fact conform to the applicable API standard.All rights reserved. No part of this work may be reproduced, translated, stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permissi

11、on from the publisher. Contact the Publisher, API Publishing Services, 1220 L Street, N.W., Washington, D.C. 20005.Copyright 2009 American Petroleum InstituteAPI ForewordNothing contained in any API publication is to be construed as granting any right, by implication or otherwise, for the manufactur

12、e, sale, or use of any method, apparatus, or product covered by letters patent. Neither should anything contained in the publication be construed as insuring anyone against liability for infringement of letters patent.Shall: As used in a standard, “shall” denotes a minimum requirement in order to co

13、nform to the specification.Should: As used in a standard, “should” denotes a recommendation or that which is advised but not required in order to conform to the specification. This document was produced under API standardization procedures that ensure appropriate notification and participation in th

14、e developmental process and is designated as an API standard. Questions concerning the interpretation of the content of this publication or comments and questions concerning the procedures under which this publication was developed should be directed in writing to the Director of Standards, American

15、 Petroleum Institute, 1220 L Street, N.W., Washington, D.C. 20005. Requests for permission to reproduce or translate all or any part of the material published herein should also be addressed to the director.Generally, API standards are reviewed and revised, reaffirmed, or withdrawn at least every fi

16、ve years. A one-time extension of up to two years may be added to this review cycle. Status of the publication can be ascertained from the API Standards Department, telephone (202) 682-8000. A catalog of API publications and materials is published annually by API, 1220 L Street, N.W., Washington, D.

17、C. 20005.Suggested revisions are invited and should be submitted to the Standards Department, API, 1220 L Street, NW, Washington, D.C. 20005, standardsapi.org.iiivContents Page API Foreword ii Foreword . v Introduction . vi 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 1 4 Symbols

18、and abbreviated terms . 5 5 Functional specification . 5 5.1 General . 5 5.2 Type description . 5 5.3 Well parameters 5 5.4 Operational parameters . 6 5.5 Environmental compatibility 6 5.6 Compatibility with related well equipment . 7 5.7 Design validation 7 5.8 Quality control . 7 6 Technical speci

19、fication 7 6.1 General . 7 6.2 Technical characteristics . 7 6.3 Design requirements 7 6.4 Design verification 11 6.5 Design validation requirements 11 6.6 Design changes 17 6.7 Design validation by scaling . 17 6.8 Other validations . 18 6.9 Assembly verification . 18 7 Suppliers/manufacturers requ

20、irements 18 7.1 General . 18 7.2 Documentation and data control . 18 7.3 Product identification . 20 7.4 Quality control . 20 8 Repair . 25 9 Shipment/storage 26 Bibliography . 30 vForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodie

21、s (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations,

22、 governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO

23、/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the m

24、ember bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 14310 was prepared by Technical Committee ISO/TC 67, Materials, equi

25、pment and offshore structures for petroleum, petrochemical and natural gas industries, Subcommittee SC 4, Drilling and production equipment. This second edition cancels and replaces the first edition (ISO 14310:2001), which has been technically revised. viIntroduction This International Standard has

26、 been developed by users/purchasers and suppliers/manufacturers of packers and bridge plugs and is intended for use in the petroleum and natural gas industry worldwide. This International Standard is intended to give requirements and information to both parties in the selection, manufacture, testing

27、 and use of packers and bridge plugs. Further, this International Standard addresses supplier/manufacturer requirements that set the minimum requirements with which it is necessary that suppliers/manufacturers comply to claim conformity with this International Standard. This International Standard h

28、as been structured to allow for grades of increased requirements both in quality control and design validation. These variations allow the user/purchaser to select the grade required for a specific application. The three quality grades provide the user/purchaser with a choice of requirements to meet

29、 a specific preference or application. Quality grade Q3 is the minimum grade of quality offered by this product standard. Quality grade Q2 provides additional inspection and verification steps, and quality grade Q1 is the highest grade provided. Additional quality requirements can be specified by th

30、e user/purchaser as supplemental requirements. Seven standard design-validation grades (V0 to V6) provide the user/purchaser with a choice of requirements to meet a specific preference or application. Design validation grade V6 is the minimum grade and represents equipment where the validation metho

31、d has been defined by the supplier/manufacturer. The complexity and severity of the validation testing increases as the grade number decreases. It is necessary that users of this International Standard be aware that requirements above those outlined in this International Standard can be needed for i

32、ndividual applications. This International Standard is not intended to inhibit a supplier/manufacturer from offering, or the user/purchaser from accepting, alternative equipment or engineering solutions. This can be particularly applicable where there is innovative or developing technology. Where an

33、 alternative is offered, it is necessary that the supplier/manufacturer identify any variations from this International Standard. INTERNATIONAL STANDARD ISO 14310:2008(E)1 Petroleum and natural gas industries Downhole equipment Packers and bridge plugs 1 Scope This International Standard provides re

34、quirements and guidelines for packers and bridge plugs as defined herein for use in the petroleum and natural gas industry. This International Standard provides requirements for the functional specification and technical specification, including design, design verification and validation, materials,

35、 documentation and data control, repair, shipment, and storage. In addition, products covered by this International Standard apply only to applications within a conduit. Installation and maintenance of these products are outside the scope of this International Standard. 2 Normative references The fo

36、llowing referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2859-1, Sampling procedures for inspection by attri

37、butes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection ISO 3601-1, Fluid power systems O-rings Part 1: Inside diameters, cross-sections, tolerances and designation codes ISO 3601-3, Fluid power systems O-rings Part 3: Quality acceptance criteria ISO 9000,

38、Quality management systems Fundamentals and vocabulary ISO 9712, Non-destructive testing Qualification and certification of personnel ISO 11960, Petroleum and natural gas industries Steel pipes for use as casing or tubing for wells ISO 15156, (all parts), Petroleum and natural gas industries Materia

39、ls for use in H2S-containing environments in oil and gas production 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 9000 and the following apply. 3.1 assembly product comprised of more than one component 3.2 bridge plug mechanical device installed in

40、, and used for blocking fluid (liquid or gas) communication in, the conduit and not installed in a designed receptacle 3.3 casing pipe extending from the surface and intended to line the walls of a drilled well 2 PACKERS AND BRIDGE PLUGS 3.4 casing size nominal casing outside diameter (OD) as specif

41、ied in ISO 11960 3.5 component individual part of an assembly 3.6 conduit casing, tubing or liner, either metallic or non-metallic 3.7 design validation process of proving a design by testing to demonstrate conformity of the product to design requirements NOTE Seven standard design validation grades

42、 (V6 to V0) are specified in 6.5. ISO/TS 29001 3.8 design verification process of examining the result of a given design or development activity to determine conformity with specified requirements NOTE These activities are described in 6.4. ISO/TS 29001 3.9 drift diameter minimum inside diameter (ID

43、) of a packer, expressed as the OD of the drift bar utilized during assembly inspection, as outlined in 7.4.11 3.10 end connection thread or other mechanism connecting the packer or bridge plug to the conduit 3.11 exposed component flow-wetted component (3.13), internally wetted component (3.18), an

44、d/or component contacted by well fluid below the packing element 3.12 extrusion gap radial gap between the maximum rated casing ID and the minimum OD immediately adjacent to the packing element 3.13 flow-wetted component component (3.5) that comes in direct contact with the dynamic movement of well

45、fluids in the flow stream 3.14 gauge OD maximum specified product OD 3.15 grade category or rank given to different requirements for quality or design validation API SPECIFICATION 11D1/ISO 14310 3 3.16 heat-traceable traceable to a unique heat treatment (heat) of material 3.17 inflatable packing ele

46、ment packer or bridge plug packing element energized to form a seal by applying fluid pressure directly to the element 3.18 internally wetted component flow-wetted component (3.13) and any component out of the flow stream, but contacted by well fluids through a port or other passage to the flow-wett

47、ed area 3.19 job lot batch of material or components that have undergone the same process or series of processes 3.20 job-lot traceable parts identifiable as originating from a job lot that designates the included heat(s) 3.21 liner pipe that does not extend from the surface and is intended to line

48、the walls of a drilled well 3.22 mandrel component(s) of a packer that contain(s) the end connections and provide(s) a conduit through the packer 3.23 manufacturing process and actions performed by an equipment supplier/manufacturer that are necessary to provide finished component(s), assemblies and

49、 related documentation that fulfil the requests of the user/purchaser and meet the standards of the supplier/manufacturer NOTE Manufacturing begins when the supplier/manufacturer receives the order and is completed at the moment the component(s), assemblies and related documentation are surrendered to a transportation provider. 3.24 NACE service packers or bridge plugs whose type 1 components (3.41) are manufactured from materials that comply with ISO 15156 (all parts) 3.25 non-conformance non-fulfilment of a specified requirement 3.26 packer mechanical d