API MPMS 3.1B-2001 Manual of Petroleum Measurement Standards Chapter 3-Tank Gauging - Section 1B-Standard Practice for Level Measurement of Liquid Hydrocarbons in Stationary Tanks .pdf

《API MPMS 3.1B-2001 Manual of Petroleum Measurement Standards Chapter 3-Tank Gauging - Section 1B-Standard Practice for Level Measurement of Liquid Hydrocarbons in Stationary Tanks .pdf》由会员分享，可在线阅读，更多相关《API MPMS 3.1B-2001 Manual of Petroleum Measurement Standards Chapter 3-Tank Gauging - Section 1B-Standard Practice for Level Measurement of Liquid Hydrocarbons in Stationary Tanks .pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、Manual of PetroleumMeasurement StandardsChapter 3Tank GaugingSection 1BStandard Practice for Level Measurement of Liquid Hydrocarbons in Stationary Tanks by Automatic Tank GaugingSECOND EDITION, JUNE 2001REAFFIRMED, AUGUST 2011Manual of PetroleumMeasurement StandardsChapter 3Tank GaugingSection 1BSt

2、andard Practice for Level Measurement of Liquid Hydrocarbons in Stationary Tanks by Automatic TankGaugingMeasurement CoordinationSECOND EDITION, JUNE 2001REAFFIRMED, AUGUST 2011SPECIAL NOTESAPI publications necessarily address problems of a general nature. With respect to partic-ular circumstances,

3、local, state, and federal laws and regulations should be reviewed.API is not undertaking to meet the duties of employers, manufacturers, or suppliers towarn and properly train and equip their employees, and others exposed, concerning healthand safety risks and precautions, nor undertaking their obli

4、gations under local, state, or fed-eral laws.Information concerning safety and health risks and proper precautions with respect to par-ticular materials and conditions should be obtained from the employer, the manufacturer orsupplier of that material, or the material safety data sheet.Nothing contai

5、ned in any API publication is to be construed as granting any right, byimplication or otherwise, for the manufacture, sale, or use of any method, apparatus, or prod-uct covered by letters patent. Neither should anything contained in the publication be con-strued as insuring anyone against liability

6、for infringement of letters patent.Generally, API standards are reviewed and revised, reafrmed, or withdrawn at least everyve years. Sometimes a one-time extension of up to two years will be added to this reviewcycle. This publication will no longer be in effect ve years after its publication date a

7、s anoperative API standard or, where an extension has been granted, upon republication. Statusof the publication can be ascertained from the API Measurement Coordination Departmenttelephone (202) 682-8000. A catalog of API publications and materials is published annu-ally and updated quarterly by AP

8、I, 1220 L Street, N.W., Washington, D.C. 20005.This document was produced under API standardization procedures that ensure appropri-ate notication and participation in the developmental process and is designated as an APIstandard. Questions concerning the interpretation of the content of this standa

9、rd or com-ments and questions concerning the procedures under which this standard was developedshould be directed in writing to the standardization manager, American Petroleum Institute,1220 L Street, N.W., Washington, D.C. 20005. Requests for permission to reproduce ortranslate all or any part of t

10、he material published herein should also be addressed to the gen-eral manager.API standards are published to facilitate the broad availability of proven, sound engineer-ing and operating practices. These standards are not intended to obviate the need for apply-ing sound engineering judgment regardin

11、g when and where these standards should beutilized. The formulation and publication of API standards is not intended in any way toinhibit anyone from using any other practices.Any manufacturer marking equipment or materials in conformance with the markingrequirements of an API standard is solely res

12、ponsible for complying with all the applicablerequirements of that standard. API does not represent, warrant, or guarantee that such prod-ucts do in fact conform to the applicable API standard.All rights reserved. No part of this work may be reproduced, stored in a retrieval system, or transmitted b

13、y any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission from the publisher. Contact the Publisher, API Publishing Services, 1220 L Street, N.W., Washington, D.C. 20005.Copyright 2001 American Petroleum InstituteFOREWORDAPI publications may be used

14、 by anyone desiring to do so. Every effort has been made bythe Institute to assure the accuracy and reliability of the data contained in them; however, theInstitute makes no representation, warranty, or guarantee in connection with this publicationand hereby expressly disclaims any liability or resp

15、onsibility for loss or damage resultingfrom its use or for the violation of any federal, state, or municipal regulation with which thispublication may conict.Suggested revisions are invited and should be submitted to the standardization manager,American Petroleum Institute, 1220 L Street, N.W., Wash

16、ington, D.C. 20005.iiiCONTENTSPage3.1B.1 SCOPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1B.2 REFERENCED PUBLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1B.3 DEFINITIONS. . . . .

17、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1B.4 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23.1B.4.1 Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . .

18、. . . . . . . . . . . . . . . . . . . . . . 23.1B.4.2 General Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23.1B.4.3 Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33.1B.4.4 Use

19、 of ATGs For Custody Transfer or Inventory Control . . . . . . . . . . . . . . . 33.1B.4.5 Installation of ATGs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43.1B.4.6 Remote Readout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20、 . . . . . . . . . 93.1B.5 GENERAL PROCEDURES FOR INITIAL SETTING AND INITIAL VERIFICATION OF ATGs IN THE FIELD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93.1B.5.1 Initial Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93.1B.5.2 R

21、eference Manual Level Measurement Procedure . . . . . . . . . . . . . . . . . . . . 93.1B.5.3 Reference Measurement Tape and Weight Certication . . . . . . . . . . . . . . . . 93.1B.5.4 Effect of Weather . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93.1

22、B.5.5 ATG TechnologySpecic Considerations . . . . . . . . . . . . . . . . . . . . . . . . . 93.1B.5.6 ApplicationSpecic Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93.1B.6 INITIAL SETTING OF ATGs IN THE FIELD . . . . . . . . . . . . . . . . . . . . . . . . . . 103.1B.6

23、.1 Ullage-Based ATGs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103.1B.6.2 Innage-Based ATGs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103.1B.7 INITIAL VERIFICATION . . . . . . . . . . . . . . . . . . . . . . . .

24、 . . . . . . . . . . . . . . . . . . 103.1B.7.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103.1B.7.2 Verication Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113.1B.7.3 Initial Verica

25、tion Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113.1B.8 RECORD KEEPING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123.1B.9 SUBSEQUENT VERIFICATION OF ATGs FOR CUSTODY TRANSFER OR INVENTORY CONTROL . . . . . .

26、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123.1B.9.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123.1B.9.2 Frequency of Subsequent Verication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123.1

27、B.9.3 Procedure for Subsequent Verication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133.1B.9.4 Tolerance for Subsequent Verication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133.1B.10 DATA COMMUNICATION AND RECEIVING . . . . . . . . . . . . . . . . . . . . . . . . 13vP

28、ageAPPENDIX A SAFETY PRECAUTIONS: PHYSICAL CHARACTERISTICS AND FIRE CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15APPENDIX B ACCURACY REQUIREMENTS FOR ATGs . . . . . . . . . . . . . . . . . . . 17Figures1 Example of an ATG (Contact or Non-contact) Mounted on a Still Pipe

29、 Supported by Tank Bottom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Example of an ATG (Contact or Non-contact) Supported by a Bracket Hinged to the Lower Tank Shell Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Example

30、 Installation of Top-Mounted ATGs on Fixed Roof Tanks Without Still Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Example Installation of Top-Mounted Innage-ATG on Fixed Roof or Floating Roof Tanks Without Still Pipe . . . . . . . . . .

31、 . . . . . . . . . . . . . . . . . . . . . . . . 8vi1Manual of Petroleum Measurement StandardsChapter 3Tank GaugingSection 1BStandard Practice for Level Measurement of Liquid Hydrocarbons in Stationary Tanks by Automatic Tank Gauging3.1B.1 ScopeThis standard covers level measurement of liquid hydro-

32、carbons in stationary, aboveground, atmospheric storagetanks using automatic tank gauges (ATGs). The standard dis-cusses automatic tank gauging in general, accuracy, installa-tion, commissioning, calibration and verication of ATGsthat measure either innage or ullage. It covers both intrusiveand non-

33、intrusive ATGs used for either custody transfer orinventory control. The standard also covers the requirementsfor data collection, transmission and receiving.This standard does not cover the following:a. Hydrocarbons having a Reid vapor pressure above 15pounds per square inch absolute (100 kPa).b. M

34、easurement of weight or mass with ATG equipment.This is covered in Chapter 3.6 and Chapter 16.2 of the Man-ual of Petroleum Measurement Standards.c. Measurement of level in underground tanks or in pressur-ized tanks storing liquid hydrocarbons.d. Conversion of tank level to liquid volume. This is co

35、veredin Chapter 12.1 of the Manual of Petroleum MeasurementStandards.e. Measurement of temperature, sampling, density and sedi-ment and water (S b. not compromise the resolution of the measurement outputsignal; c. provide proper security and protection of the measureddata to ensure its integrity;d.

36、provide adequate speed to meet the update time requiredfor the receiving unit;e. be electromagnetically immune.15APPENDIX ASAFETY PRECAUTIONS: PHYSICAL CHARACTERISTICS AND FIRE CONSIDERATIONSPersonnel involved with handling petroleum-related substances and other chemical mate-rials should be familia

37、r with the materials physical and chemical characteristics, includingpotential for re, explosion, and reactivity and appropriate emergency procedures. Thesepersonnel should comply with safe operating practices of the individual company and local,state and federal regulations, including use of proper

38、 protective clothing and equipment. Per-sonnel should be alert to potential sources of ignition and should keep containers of materi-als closed when not in use.Note: Information regarding particular materials and conditions should be obtained from the employer,manufacturer, or supplier of that mater

39、ial, or the material safety data sheet.17APPENDIX BACCURACY REQUIREMENTS FOR ATGS (See Note)Requirement Custody Transfer InventoryFactory calibration 1 mm (1/16inch) 3 mm (1/8inch)Effect of installation 3 mm (1/8inch) n.a.Initial verication 4 mm (3/16inch) 25 mm (1 inch)Subsequent verication 4 mm (3

40、/16inch) 25 mm (1 inch)Frequency of verication monthly quarterlyNote: This table is for reference only. Please refer to the entire document.Invoice To (o Check here if same as “Ship To”)Name:Title:Company:Department:Address:City: State/Province:Zip/Postal Code: Country:Telephone:Fax:E-Mail:oPayment

41、Enclosed oP.O. No. (Enclose Copy)oCharge My Global Account No. oVISAoMasterCardoAmerican ExpressoDiscoverCredit Card No.:Name (As It Appears on Card):Expiration Date:Signature:Quantity Product Number Title TotalSubtotalApplicable Sales Tax (see below)Rush Shipping Charge (see below)Shipping and Hand

42、ling (see below)Total (in U.S. Dollars)*To be placed on Standing Order for future editions of this publication, place a check mark in the SO column and sign here: Pricing and availability subject to change without notice.Date:SO* Unit PriceAmerican Petroleum Institute Related Publications Order Form

43、 - 2001oAPI Member (Check if Yes)Ship To (UPS will not deliver to a P.O. Box)Name:Title:Company:Department:Address:City: State/Province:Zip/Postal Code: Country:Telephone:Fax:E-Mail:Available through Global Engineering DocumentsPhone Orders: 1-800-854-7179 (Toll-free in the U.S. and Canada) 303-397-

44、7956 (Local and International) Fax Orders: 303-397-2740Online Orders: H031A1 Chapter 3.1A, Manual Gauging of Petroleum and Petroleum Products$ 50.00Mail Orders Payment by check or money order in U.S. dollars is required except for established accounts. State and local taxes, plus 5% for shipping and

45、 handling, must be added.Send mail orders to: API Publications, Global Engineering Documents, 15 Inverness Way East, M/S C303B, Englewood, CO 80112-5776, USA.Purchase Orders Purchase orders are accepted from established accounts. Invoice will include actual freight cost, an $8.00 handling fee, plus

46、state and local taxes.Telephone Orders If ordering by telephone, an $8.00 handling fee and actual freight costs will be added to the order.Sales Tax All U.S. purchases must include applicable state and local sales tax. Customers claiming tax-exempt status must provide Global with a copy of their exe

47、mptioncertificate.Shipping (U.S. Orders) Orders shipped within the U.S. are sent via traceable means. Most orders are shipped the same day. Subscription updates are sent by First-Class Mail.Other options, including next-day service, air service, fax transmission, and electronic delivery are availabl

48、e at additional cost.Shipping (International Orders) Standard international shipping is by air express courier service. Subscription updates are sent by World Mail. Normal delivery is 3-4 days fromshipping date.Rush Shipping Fee In addition to the carrier charges, the following charges will be added

49、: Next Day Delivery orders placed prior to 2:00 p.m. MST - $10.00 / Next Day Deliveryorders placed after 2:00 p.m. MST - $20.00 (if time is available for order processing)Returns All returns must be pre-approved by calling Globals Customer Service Department at 1-800-624-3974 for information and assistance. There may be a 15% restocking fee.Special order items, electronic documents, and age-dated materials are non-returnable.$ 66.00$ 55.00$ 55.00$ 66.00$ 55.00Chapter 3.2, Tank GaugingGauging Petroleum and Petroleum Produc