BS S 162-1990 Specification for 18% nickel-cobalt-molybdenum maraging steel forging stock forgings bars and parts (1800 MPa double vaccuum melted)《锻坯、锻件、棒材和零件用18%镍-钴-钼马氏体时效钢(1800MPa 双倍真空熔化)规范》.pdf
《BS S 162-1990 Specification for 18% nickel-cobalt-molybdenum maraging steel forging stock forgings bars and parts (1800 MPa double vaccuum melted)《锻坯、锻件、棒材和零件用18%镍-钴-钼马氏体时效钢(1800MPa 双倍真空熔化)规范》.pdf》由会员分享,可在线阅读,更多相关《BS S 162-1990 Specification for 18% nickel-cobalt-molybdenum maraging steel forging stock forgings bars and parts (1800 MPa double vaccuum melted)《锻坯、锻件、棒材和零件用18%镍-钴-钼马氏体时效钢(1800MPa 双倍真空熔化)规范》.pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARD AEROSPACE SERIES BS S 162:1990 Incorporating Amendments Nos. 1 and 2 Specification for 18 % nickel-cobalt- molybdenum maraging steel for forging stock, forgings, bars and parts (1800 MPa: double vacuum melted)BS S 162:1990 This British Standard, having been prepared under the direct
2、ion of the Aerospace Standards Policy Committee, was published under the authority of the Board of BSI and comes into effect on 31 October 1990 BSI 17 October-2005 The following BSI references relate to the work on this standard: Committee reference ACE/15 Draft for comment 89/75368 DC ISBN 0 580 18
3、986 4 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Technical Committee ACE/15 upon which the following bodies were represented: British Forging Industry Association British Independent S
4、teel Producers Association British Industrial Fasteners Federation British Investment Casting Trade Association British Steel Industry British Steel Industry (Wire Section) Civil Aviation Authority (Airworthiness Division) Institute of British Foundrymen Ministry of Defence National Association of S
5、teel Stockholders Rolls-Royce Limited Seamless Steel Tube Association Society of British Aerospace Companies Limited Steel Casting Research and Trade Association Amendments issued since publication Amd. No. Date of issue Comments 6373 July 1991 16005 October 2005 Indicated by a sideline in the margi
6、nBS S 162:1990 BSI 17 October-2005 i Contents Page Committees responsible Inside front cover Foreword ii 1S c o p e 1 2 References 1 3 Technical requirements 1 Table 1 Technical requirements for 18 % Ni-Co-Mo maraging steel 2BS S 162:1990 ii BSI 17 October-2005 Foreword This British Standard has bee
7、n prepared under the direction of the Aerospace Standards Policy Committee and is a revision of MoD (PE) Specification DTD 5212, which it supersedes. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correc
8、t application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 3 and a back cover. This standard has been updated (see copyright date) and may have
9、had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS S 162:1990 BSI 17 October-2005 1 1 Scope This British Standard specifies the chemical composition, mechanical properties and inspection and test requirements for an 18 % nickel-cobalt-molybdenum m
10、araging steel (iron base, Ni 18, Co 7.75, Mo 4.9) supplied in the following forms and as parts for general aerospace use: a) forging stock, designation S 162A, columns 2 and 3 of Table 1; b) forgings, designation S 162C, columns 4, 5 and 6 of Table 1; c) black bars for machining, designation S 162B,
11、 columns 7, 8 and 9 of Table 1; d) bright bars for machining, designation S 162D, columns 10, 11 and 12 of Table 1. 2 References This standard makes reference to the following standards publications: BS S 100, Procedure for inspection and testing of wrought steels (other than sheet, strip and tubes)
12、. BS EN 2500, Guidelines for the preparation and use of standards for metallic materials 1) . 3 Technical requirements 3.1 The material in its delivery and use conditions shall comply with Table 1, the format and nomenclature of which comply with BS EN 2500. 3.2 This standard shall be used in conjun
13、ction with BS S 100, as given in Table 1, or as given in 3.3 to 3.5. 3.3 One sample from the top and bottom of each ingot shall be taken for sulphur printing or deep etching tests. 3.4 The material shall be overall dressed. 3.5 Finished parts shall be supplied in the solution treated and maraged con
14、dition and shall comply with sections 1 and 7 of BS S 100. (Text deleted) 3.6 Where it is necessary to recover coarse grain structures, this shall be by the use of a refining treatment at 950 10C followed by AC or WQ prior to solution treatment. Where such refining thermal cycles are applied, the tr
15、eatment details shall be stated on the certificate of conformity. 1) In preparation.BS S 162:1990 2 BSI 17 October-2005 Table 1 Technical requirements for 18 % Ni-Co-Mo maraging steel 1 Chemical composition % Element N C Si Mn P S Al B Ca Co Cr Mo Ni Ti Zr Fe min. 0.05 7.0 4.6 17.0 0.30 Base max. 0.
16、005 0.010 0.10 0.10 0.010 0.010 0.15 0.005 0.05 8.5 0.25 5.2 19.0 0.60 0.02 2 1 2 3 4 5 6 3 Method of melting Vacuum induction melted and vacuum arc remelted 4 Form Method of production Limit dimensions Forging stock Forgings 5 Acceptance standards Sections 1 and 5 of BS S 100 Sections 1 and 6 of BS
17、 S 100 6 Condition of supply and heat treatment prior to delivery As forged or as rolled Solution treated 820 C 10 C/AC (1) 7 Condition of use and heat treatment prior to use As supplied Condition of supply and maraged = 485 C 10 C/ W 3 h/AC 8 Test piece Heat treatment Sampling Reference heat treatm
18、ent See line 29 As condition of supply Reference heat treatment see line 29 9 Dimensions concerned D or a mm 75 W75 75 W 75 10 Thickness of cladding on each face % 11 Direction of sample L T L T 12 Tensile Temperature C Ambient temperature 13 Proof stress R p0.2 MPa W 1 700 W 1 700 14 Strength R m M
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSS1621990SPECIFICATIONFOR18NICKELCOBALTMOLYBDENUMMARAGINGSTEELFORGINGSTOCKFORGINGSBARSANDPARTS1800MPADOUBLEVACCUUMMELTED

链接地址:http://www.mydoc123.com/p-399119.html