BS PD ISO TR 17329-2015 Gas cylinders Identification of gas cylinder manufacturer marks and their assigned radio frequency identification (RFID) codes《气瓶 气瓶生产商标记及其分配的射频识别 (RFID) 码的识别》.pdf

《BS PD ISO TR 17329-2015 Gas cylinders Identification of gas cylinder manufacturer marks and their assigned radio frequency identification (RFID) codes《气瓶 气瓶生产商标记及其分配的射频识别 (RFID) 码的识别》.pdf》由会员分享，可在线阅读，更多相关《BS PD ISO TR 17329-2015 Gas cylinders Identification of gas cylinder manufacturer marks and their assigned radio frequency identification (RFID) codes《气瓶 气瓶生产商标记及其分配的射频识别 (RFID) 码的识别》.pdf（44页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication Gas cylinders Identification of gas cylinder manufacturer marks and their assigned radio frequency identification (RFID) codes PD ISO/TR 17329:2015National foreword This Published Document is the UK implementation of ISO/TR 17329:2015. The UK participation in its preparatio

2、n was entrusted by Technical Committee PVE/3, Gas containers, to Subcommittee PVE/3/7, Gas containers - Gas cylinder (receptacle) operations. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necess

3、ary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015 ISBN 978 0 580 83688 6 ICS 23.020.30 Compliance with a British Standard cannot confer immunity from legal obligations. This Published Docum

4、ent was published under the authority of the Standards Policy and Strategy Committee on 30 November 2015. Amendments/corrigenda issued since publication Date Text affected PUBLISHED DOCUMENT PD ISO/TR 17329:2015 ISO 2015 Gas cylinders Identification of gas cylinder manufacturer marks and their assig

5、ned radio frequency identification (RFID) codes Bouteilles gaz Identification des marques de fabricant de la bouteille de gaz et leurs codes didentification (RFID) de frquences radio TECHNICAL REPORT ISO/TR 17329 Reference number ISO/TR 17329:2015(E) First edition 2015-11-01 PD ISO/TR 17329:2015 ISO

6、/TR 17329:2015(E)ii ISO 2015 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photo

7、copying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22

8、 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.org PD ISO/TR 17329:2015 ISO/TR 17329:2015(E)Foreword iv Introduction v 1 Scope . 1 2 General 1 3 Explanation of columns . 2 Annex A (informative) List of codes and identification marks for gas cylinder manufacturers 3 Annex B (informative) In

9、structions to revise list of manufacturer marks.33 Annex C (informative) Current list of codes and identification marks for gas cylinder manufacturers34 Bibliography .35 ISO 2015 All rights reserved iii Contents Page PD ISO/TR 17329:2015 ISO/TR 17329:2015(E) Foreword ISO (the International Organizat

10、ion for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established h

11、as the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The

12、 procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the ed

13、itorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent r

14、ights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an

15、explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this

16、 document is ISO/TC 58, Gas cylinders, Subcommittee SC 4, Operational requirements for gas cylinders.iv ISO 2015 All rights reserved PD ISO/TR 17329:2015 ISO/TR 17329:2015(E) Introduction The purpose of this Technical Report is to provide the gas cylinder manufacturing industry, the approval authori

17、ties, the inspection bodies, the gas industry and all associated industry branches dealing with gas cylinders a tool for identifying gas cylinders with their manufacturers marks and their assigned radio frequency identification (RFID) codes. ISO 2015 All rights reserved v PD ISO/TR 17329:2015 Gas cy

18、linders Identification of gas cylinder manufacturer marks and their assigned radio frequency identification (RFID) codes 1 Scope This Technical Report provides an inventory, as far as known at time of publication, of manufacturers identification marks and their assigned radio frequency identificatio

19、n (RFID) codes according to ISO 21007-1 and ISO 21007-2. The listing includes marks of existing gas cylinder manufacturers, as well as cylinder manufacturers which have ceased production in the past, but whose cylinders can still be in service today. NOTE It is intended to revise Annex A of this Tec

20、hnical Report from time to time in order to update the list of codes and identification marks of gas cylinder manufacturers in accordance with the progressing commercial and economic development in the cylinder manufacturing industry. Any request for inclusion or modification of these identification

21、s is to be made to the ISO/TC 58/SC 4 Secretariat, who would update the information in Annex A after consultation with the committee leadership. 2 General There is a general marking requirement by national or international regulations and standards to identify gas cylinders with the cylinder manufac

22、turers identification (name, trademark and/or logo), e.g. by stamp marking, or for composite cylinders, by labelling, in order to guarantee their traceability. In certain circumstances, it is very important to enable a distinctive identification of the origin of the cylinder. Normally for a given ma

23、nufacturer, the identification is specific to a manufacturing location. When, in addition to the above marking requirements, the cylinders are identified by radio frequency identification (RFID) codes, the technologies and RFID codes in accordance with ISO 21007 are used. The first three digits of t

24、he RFID codes listed in Column 1 of Annex A are the country code as listed in ISO 3166-1. The subsequent two digits are assigned consecutively in the countrys listing. Once assigned, the RFID code designation does not change. Annex A lists cylinder manufacturers by countries which are currently know

25、n to produce or have produced gas cylinders. The list does not claim to be complete and is valid only as of the date of the publication of this Technical Report. Manufacturers that no longer produce cylinders remain in Annex A as their cylinders could still be in service and need to be identified. I

26、t is expected that the manufacturers are using manufacturers marks which identify unambiguously the manufacturing plant/facility to clearly identify the plant to which the type approval of the concerned cylinder was assigned. Annex A clearly indicates the date when the manufacturing at the old plant

27、/facility ends and the date when the new plant/facility begins manufacturing cylinders. Names of manufacturers may have changed over time; however, these manufacturers may have continued using the same manufacturers mark provided the approval criteria for the cylinders in question have not changed.

28、Vice versa, a change of the manufacturers mark may have taken place or alternative marks may be used by one and the same manufacturer. Clause 3 explains the information provided in each column of Annex A. To provide updates to the list of manufacturers, use the link provided in Annex B for instructi

29、ons to submit new/revised information. These revisions, once approved by ISO/TC 58/SC 4 and designated with an RFID code, will be provided on Standards Maintenance Portal at the link provided in Annex C. TECHNICAL REPORT ISO/TR 17329:2015(E) ISO 2015 All rights reserved 1 PD ISO/TR 17329:2015 ISO/TR

30、 17329:2015(E) 3 Explanation of columns The column entitled “Code” designates the RFID code for a manufacturer. Note This code is assigned by the experts of ISO/TC 58/SC 4. The column entitled “Manufacturer name” designates the official name of the gas cylinder manufacturer. It should be noted that

31、the name may have changed over time. The column entitled “Location of manufacturing plant/facility” designates the plant/facility responsible for manufacturing and to which the mark is assigned. The column entitled “Year(s) of manufacture” designates the years for which the manufacturers mark(s) wer

32、e used, if known. For example, “ 1927” means the mark was used inclusive of 1927, “1927 1961” means the mark was used from some time in 1927 to some time during 1961, and “2002 ” means the mark has been used starting some time during 2002 to present. The column entitled “Manufacturers mark” provides

33、 the official manufacturers identification that is marked on the cylinder as required by ISO 13769 (stamp marking 3 in ISO 13769, Table 1). Country: XXXXX Code Manufacturer name Location of manufacturing plant/facility Year(s) of manufacture Manufacturers mark2 ISO 2015 All rights reserved PD ISO/TR

34、 17329:2015 ISO/TR 17329:2015(E) Annex A (informative) List of codes and identification marks for gas cylinder manufacturers The following list does not claim to be complete and is current as of 2014-07-24. Country: ALGERIA Code Manufacturer name Location of manufacturing plant/facility Year(s) of m

35、anufacture Manufacturers mark 012 01 F.E.R.A.P. (Fabrication et entretien de rcipients pression) Algiers Country: ARGENTINA Code Manufacturer name Location of manufacturing plant/facility Year(s) of manufacture Manufacturers mark 032 01 LAir Liquide Buenos Aires1960 1985 032 02 Drago Buenos Aires 19

36、38 M D 032 03 Fabricacion Militar 032 04 Gas Carbonic Argentina G.C.A. 032 05 Gonzalez & Chiesa Changed to Inflex Argentoil S.A. San Luis 1967 INFLEX 032 06 Pablo Casale 1958 1986 CASALE 032 07 Saravia Y Lopez Buenos Aires 1993 L S ISO 2015 All rights reserved 3 PD ISO/TR 17329:2015 ISO/TR 17329:201

37、5(E) Country: ARGENTINA Code Manufacturer name Location of manufacturing plant/facility Year(s) of manufacture Manufacturers mark 032 08 Oxi Luz 032 09 Acetylene Buenos Aires 1972 1992 032 10 Miguel Balbona 032 11 R. Batalles S.A. Buenos Aires 1944 032 12 Propulsora San Luis San Luis 032 13 Luis Pas

38、quinelli e Hijos Buenos Aires 1947 032 14 Kioshi Compresion Buenos Aires 2005 032 15 Mozart Buenos Aires 1995 032 16 INPROCIL S.A. Entre Rios 2007 032 17 CIDEGAS S.A. Buenos Aires 2004 Country: AUSTRALIA Code Manufacturer name Location of manufacturing plant/facility Year(s) of manufacture Manufactu

39、rers mark 036 01 Manchester Tank & Equipment CO Echuca MANCHESTER 036 02 CIG Gas Cylinders 1996 CIG 036 03 Luxfer Gas Cylinders Sydney 1997 2004 LUXFER4 ISO 2015 All rights reserved PD ISO/TR 17329:2015 ISO/TR 17329:2015(E) Country: AUSTRIA Code Manufacturer name Location of manufacturing plant/faci

40、lity Year(s) of manufacture Manufacturers mark 040 01 Jos. Heiser Changed to Worthington Heiser Changed to Worthington Cylinders GmbH Kienberg 1927 1927 1961 1961 1976 1976 2001 HEISER 2002 040 02 iSi GmbH Wien 1994 (3 alternative symbols used) ISI ISO 2015 All rights reserved 5 PD ISO/TR 17329:2015

41、 ISO/TR 17329:2015(E) Country: BELGIUM Code Manufacturer name Location of manufacturing plant/facility Year(s) of Manufacture Manufacturers mark 056 01 S.A. Ateliers Belges Runis (formerly S.A. des Ateliers de la Dyle) La Dyle-Louvain 1962 056 02 tablissements Champy Antwerp 1940 RB 056 03 S.A. Come

42、t Mechelen 1980 S.A.COMET.Malines 1980 C.M 056 04 S.A. Standard Van Leer (formerly S.A. Usines Standard) Lierre U S . 056 05 S.A. Des Usines A Tubes de la Meuse Flmalle-Haute (Lige)T MU Country: BRAZIL Code Manufacturer name Location of manufacturing plant/facility Year(s) of manufacture Manufacture

43、rs mark 076 01 Worthington Cylinders Itu 2002 2003 076 02 Worthington Tank Itu 2002 2003 076 03 MAT A/A So Paulo6 ISO 2015 All rights reserved PD ISO/TR 17329:2015 ISO/TR 17329:2015(E) Country: CANADA Code Manufacturer name Location of manufacturing plant/facility Year(s) of manufacture Manufacturer

44、s mark 124 01 Canadian Cylinder Company, Ltd Brantford, Ontario C 124 02 Engineering Products of Canada Ltd Boucherville, QubecE.P.C.L 124 03 Forges HPC Ltee Cap-de-la-Madeleine Qubec124 04 Hugh Canning Industries, Inc. Toronto, Ontario124 05 Aircom Industries (76) Ltd Edmonton, AlbertaM4803 124 06

45、Bruin Engineered Parts, Inc. Midland, OntarioBRUINM8802 124 07 Gas Cylinder Technologies Tecumseh, OntarioM9001 124 08 Kadet Engineering, Inc. Mississauga, Ontario KENG 124 09 Metal-Flo Corporation Canada Limited Guelph, OntarioMFCCL 124 10 Wolfedale Engineering, Ltd Mississauga, Ontario 2007 WENG o

46、r M8903 124 11 Steel Cylinder Manufacturing changed to Worthington Cylinders Tilbury, Ontario 1996 SCM or M8004 1996 2002 M8004 2002 M8004 or 124 12 Dynetek Industries Ltd. changed to Luxfer Canada Limited Calgary, Alberta March 1, 2007 M5550 March 1, 2007 M0501 ISO 2015 All rights reserved 7 PD ISO

47、/TR 17329:2015 ISO/TR 17329:2015(E) Country: CHINA Code Manufacturer name Location of manufacturing plant/facility Year(s) of manufacture Manufacturers mark 156 01 Beijing Tianhai Industry Co., Ltd. Beijing 1978 JP 156 02 Changzhou Aircraft Manufacture Co., Ltd. Changzhou, Jiangsu Province 1980 CAF

48、156 03 Chengdu Great High Pressure Vessel Co., Ltd. Chengdu, Sichuan Province 1978 CG 156 04 Chongqing Yifeng High-pressure Container Co., Ltd. Chongqing 1987 YM 156 05 Juhua Group Corp- Engineering Co., Ltd. Quzhou, Zhejiang Province 2002 JG 156 06 Ningbo Meike Acetylene Cylinders Co., Ltd. Cicheng

49、 Town, Ningbo 1984 NB 156 07 Shanghai Ronghua High-Pressure Vessel Co., Ltd. Shanghai 1979 HT 156 08 Shanghai Huasheng Enterprises (Group) Co., Ltd. Shanghai 2002 SG 156 09 Tianjin Tianhai High Pressure Container Co., Ltd. Tianjin 2003 JP1 156 10 Shanghai Tianhai Dekun Composite Cylinders Co., Ltd. Shanghai 2005 JP2 156 11 Langfang Tianhai High Pressure Container Co., Ltd. Langfang, Hebei Province 2008