BS PD IEC TS 62564-1-2016 Process management for avionics Aerospace qualified electronic components (AQEC) Integrated circuits and discrete semiconductors《航空电子设备的过程管理 航空航天.pdf

《BS PD IEC TS 62564-1-2016 Process management for avionics Aerospace qualified electronic components (AQEC) Integrated circuits and discrete semiconductors《航空电子设备的过程管理 航空航天.pdf》由会员分享，可在线阅读，更多相关《BS PD IEC TS 62564-1-2016 Process management for avionics Aerospace qualified electronic components (AQEC) Integrated circuits and discrete semiconductors《航空电子设备的过程管理 航空航天.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、Process management for avionics Aerospace qualified electronic components (AQEC) Part 1: Integrated circuits and discrete semiconductors PD IEC/TS 62564-1:2016 BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06National foreword This Published Document is the UK implem

2、entation of IEC/TS 62564-1:2016. It supersedes DD IEC/TS 62564-1:2011 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee GEL/107, Process management for avionics. A list of organizations represented on this committee can be obtained on request to its sec

3、retary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016 ISBN 978 0 580 93071 3 ICS 03.100.50; 31.020; 49.060 Compliance with a B

4、ritish Standard cannot confer immunity from legal obligations. This Published Document was published under the authority of the Standards Policy and Strategy Committee on 31 July 2016. Amendments/corrigenda issued since publication Date Text affected PUBLISHED DOCUMENT PD IEC/TS 62564-1:2016 IEC TS

5、62564-1 Edition 3.0 2016-07 TECHNICAL SPECIFICATION Process management for avionics Aerospace qualified electronic components (AQEC) Part 1: Integrated circuits and discrete semiconductors INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 03.100.50; 31.020; 49.060 ISBN 978-2-8322-3513-3 Registered trade

6、mark of the International Electrotechnical Commission Warning! Make sure that you obtained this publication from an authorized distributor. PD IEC/TS 62564-1:2016 2 IEC TS 62564-1:2016 IEC 2016 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope 6 2 Normative references. 6 3 Terms, definitions and abbrev

7、iations 7 3.1 Terms and definitions 7 3.2 Abbreviations 9 4 Technical requirements 9 4.1 AQEC plan 9 4.2 AQEC documentation 10 4.2.1 General . 10 4.2.2 AQEC data sheet . 10 4.2.3 Material content . 10 4.2.4 AQEC visibility . 10 4.2.5 AQEC life expectancy 10 4.2.6 Device technology 11 4.2.7 SEE data

8、. 11 4.2.8 Termination finish 11 4.2.9 Third party part numbers 11 4.3 AQEC performance . 12 4.3.1 Performance 12 4.3.2 Functional parameters 13 4.3.3 Known limitations . 13 4.4 Quality system certification 13 4.5 Component qualification and re-qualification 13 4.6 AQEC quality assurance and reliabi

9、lity monitoring . 13 4.7 Product change notification (PCN) . 14 4.8 Last time buy (LTB) notification . 14 4.9 Obsolescence management . 14 4.10 Counterfeit prevention . 14 4.11 User or customer guide . 14 Annex A (informative) AQEC material content and construction table 15 Annex B (informative) Add

10、itional desired data 17 Bibliography . 18 Table A.1 AQEC material content and construction . 15 PD IEC/TS 62564-1:2016IEC TS 62564-1:2016 IEC 2016 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ PROCESS MANAGEMENT FOR AVIONICS AEROSPACE QUALIFIED ELECTRONIC COMPONENTS (AQEC) Part 1: Integrated circuit

11、s and discrete semiconductors FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions con

12、cerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Th

13、eir preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates

14、 closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the r

15、elevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that t

16、he technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maxi

17、mum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies

18、provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC

19、 or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and exp

20、enses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Att

21、ention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. The main task of IEC technical committees is to prepare International Standards. In exceptional c

22、ircumstances, a technical committee may propose the publication of a technical specification when the required support cannot be obtained for the publication of an International Standard, despite repeated efforts, or the subject is still under technical development or where, for any other reason, th

23、ere is the future but no immediate possibility of an agreement on an International Standard. Technical specifications are subject to review within three years of publication to decide whether they can be transformed into International Standards. IEC TS 62564-1, which is a technical specification, ha

24、s been prepared by IEC technical committee 107: Process management for avionics. PD IEC/TS 62564-1:2016 4 IEC TS 62564-1:2016 IEC 2016 This third edition cancels and replaces the second edition, published in 2011. This edition constitutes a technical revision. This edition includes the following sig

25、nificant technical changes with respect to the previous edition: a) IEC TS 62239 changed to IEC TS 62239-1, and IEC PAS 62686-1 changed to IEC TS 62686-1; b) JESD48 changed to J-STD-048 and added to the Bibliography; c) AEC-Q100 revision G changed to AEC-Q100:2014 in 4.5 (which is now revision H); d

26、) revision of AEC-Q101 removed in Bibliography; e) J-STD-609 for “Marking and labelling” added to the Bibliography; f) information added regarding components life expectancy in 4.2.5. GEIA-STD-0002-001 (June 2006), Aerospace Qualified Electronic Component (AQEC) Requirements, Volume 1 Integrated Cir

27、cuits and Semiconductors, has served as a basis for the elaboration of this technical specification. The text of this technical specification is based on the following documents: Enquiry draft Report on voting 107/276/DTS 107/283/RVC Full information on the voting for the approval of this technical

28、specification can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 62564 series, under the general title Process management for avionics Aerospace qualified electronic co

29、mponents (AQEC), can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication w

30、ill be transformed into an International standard, reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. PD IEC/TS 62564-1:2016IEC TS 62564-1:2016 IEC 2016 5 INTRODUCTION Aerospace qualified electronic components (AQ

31、EC) plans are developed by manufacturers in order to document compliance with AQEC requirements. For AQEC designated components, the intention is to a) provide AQEC users access to information from the AQEC manufacturers that is necessary for using commercial-off-the-shelf (COTS) products; b) better

32、 enable AQEC users to assess whether these parts are capable of operating reliably in their applications; c) minimize deviations from the AQEC manufacturers COTS products; d) have minimal impact on the AQEC manufacturers standard operating or business procedures; e) promote communication between the

33、 AQEC manufacturers and users. PD IEC/TS 62564-1:2016 6 IEC TS 62564-1:2016 IEC 2016 PROCESS MANAGEMENT FOR AVIONICS AEROSPACE QUALIFIED ELECTRONIC COMPONENTS (AQEC) Part 1: Integrated circuits and discrete semiconductors 1 Scope This part of IEC 62564, which is a Technical Specification, defines th

34、e minimum requirements for integrated circuits and semiconductors which are designated as an “aerospace qualified electronic component (AQEC)”. It applies to integrated circuits and semiconductors exhibiting the following attributes: a) a minimum set of requirements, or information provided by the p

35、art manufacturer, which will allow a standard COTS component to be designated AQEC by the manufacturer; b) as a minimum, each COTS component (designated AQEC) will have been designed, fabricated, assembled, and tested in accordance with the component manufacturers requirements for standard data book

36、 components; c) qualification of, and quality systems for, the COTS components to be designated as AQEC should include the manufacturers standards, operating procedures, and technical specifications. This information should be available when requested; d) components manufactured before the manufactu

37、rer has addressed AQEC requirements, but utilizing the same processes, are also considered AQEC compliant; e) additional desired attributes of a device designated AQEC (that will support AQEC users) are found in Annex B of this technical specification. NOTE Parts qualified to military specifications

38、 (except those identified as being for “logistic support” purposes only) are considered AQEC; the remainder of this technical specification only addresses non-military specification parts. Parts qualified to AEC-Q100, grade 0 through to grade 3 are considered AQEC. For those applications where a 0 C

39、 to +70 C temperature range is appropriate, grade 4 is also considered to be AQEC. The users should document that the grade category used is compatible with the application in accordance with their IEC TS 62239-1 electronic components management plan (ECMP). 2 Normative references The following docu

40、ments are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC TS 62239-1,

41、 Process management for avionics Management plan Part 1: Preparation and maintenance of an electronic components management plan IEC 62396-1, Process management for avionics Atmospheric radiation effects Part 1: Accommodation of atmospheric radiation effects via single event effects within avionics

42、electronic equipment IEC TS 62668-1, Process management for avionics Counterfeit prevention Part 1: Avoiding the use of counterfeit, fraudulent and recycled electronic components ISO 9001, Quality management systems Requirements PD IEC/TS 62564-1:2016IEC TS 62564-1:2016 IEC 2016 7 J-STD-048, Notific

43、ation Standard for Product Discontinuance 3 Terms, definitions and abbreviations For the purposes of this document, the following terms, definitions and abbreviations apply. 3.1 Terms and definitions 3.1.1 AQEC specification document prepared by or for the manufacturer to describe an AQEC product No

44、te 1 to entry: It includes a data sheet and may include other documents, such as material descriptions, environmental test procedures, quality monitoring processes, etc. It may be a stand-alone document or a clearly denoted item within a larger documentation system. There may be additional data asso

45、ciated with specific applications which may be requested separately. 3.1.2 AQEC plan instrument prepared by the plan owner (see 3.1.10) that clearly, concisely, and unambiguously documents the processes used by the plan owner to satisfy the requirements of this technical specification Note 1 to entr

46、y: The plan contains auditable content. 3.1.3 assessment evaluation of a plan owners AQEC plan to determine if it is compliant with this technical specification Note 1 to entry: It may be conducted by IECQ, the customer, the customers designee, or by a third party designated by the customer communit

47、y. 3.1.4 microcircuit integrated circuit microcircuit (device with a high circuit-element density) in which all or some of the circuit elements are inseparably associated and electrically interconnected (on one or more substrates, in a unique indivisible package) so that the microcircuit is consider

48、ed to be indivisible for the purpose of construction and commerce 3.1.5 semiconductor discrete semiconductor device semiconductor device that is specified to perform an elementary function and that is not divisible into separate components functional in themselves (for example diodes, transistors, o

49、ptocouplers, LEDs and related products) 3.1.6 component part microcircuit, integrated circuit, semiconductor or discrete semiconductor for the purpose of this specification PD IEC/TS 62564-1:2016 8 IEC TS 62564-1:2016 IEC 2016 3.1.7 customer user designer original equipment manufacturer (OEM) that procures integrated circuits and/or semiconductor devices compliant with this technical specification and uses them to design, produce, and maintain systems 3.1.8 customer communi