BS PD CEN TS 16650-2014 Specification for hose couplings for petrol oil and lubricants High pressure couplings《石油、汽油和润滑油用软管接头规范 第2部分 高压接头》.pdf

《BS PD CEN TS 16650-2014 Specification for hose couplings for petrol oil and lubricants High pressure couplings《石油、汽油和润滑油用软管接头规范 第2部分 高压接头》.pdf》由会员分享，可在线阅读，更多相关《BS PD CEN TS 16650-2014 Specification for hose couplings for petrol oil and lubricants High pressure couplings《石油、汽油和润滑油用软管接头规范 第2部分 高压接头》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication PD CEN/TS 16650:2014 Specification for hose couplings for petrol, oil and lubricants High pressure couplingsPD CEN/TS 16650:2014 PUBLISHED DOCUMENT National foreword This Published Document is the UK implementation of CEN/TS 16650:2014. It supersedes BS 2464-2:1969 which is

2、 withdrawn. The UK participation in its preparation was entrusted to Technical Committee PRI/66, Rubber and plastics tubing, hoses and hose assemblies. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all

3、the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2014. Published by BSI Standards Limited 2014 ISBN 978 0 580 77494 2 ICS 23.040.70; 49.050 Compliance with a British Standard cannot confer immunity from legal obligations. Th

4、is Published Document was published under the authority of the Standards Policy and Strategy Committee on 30 June 2014. Amendments/corrigenda issued since publication Date T e x t a f f e c t e dPD CEN/TS 16650:2014TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN/TS 16650

5、June 2014 ICS 23.040.70; 49.050 English Version Specification for hose couplings for petrol, oil and lubricants - High pressure couplings Spcifications pour les raccords de tuyaux pour essence, huile et lubrifiants - Raccords haute pression Spezifikation fr Schlauchkupplungen fr Benzin, l und Schmie

6、rstoffe - Hochdruckkupplungen This Technical Specification (CEN/TS) was approved by CEN on 16 December 2013 for provisional application. The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their comments, particula

7、rly on the question whether the CEN/TS can be converted into a European Standard. CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level in an appropriate form. It is permissible to keep conflicting n

8、ational standards in force (in parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav

9、Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE N

10、ORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TS 16650:2014 EPD CEN/TS 16650:2014 CEN/TS 16650:2014 (E) 2 Contents

11、 Page Foreword 3 1 Scope 4 2 Normative references 4 3 Information to be supplied by the purchaser .4 4 Designation of sizes of couplings 4 5 Materials .4 6 Dimensions .4 7 Coupling finish .5 8 Screw threads 5 9 Washers 5 10 Bonding 5 11 Hydrostatic test 5 12 Identification marking .5 PD CEN/TS 16650

12、:2014 CEN/TS 16650:2014 (E) 3 Foreword This document (CEN/TS 16650:2014) has been prepared by Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies”, the secretariat of which is held by BSI. Attention is drawn to the possibility that some of the elements of this document may

13、be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to announce this Technical Specification: Aust

14、ria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Swede

15、n, Switzerland, Turkey and the United Kingdom. PD CEN/TS 16650:2014 CEN/TS 16650:2014 (E) 4 1 Scope This Technical Specification specifies requirements for couplings of 2 in (50,8 mm), 2 in (63,5 mm), 3 in (76,2 mm) and 4 in (101,6 mm) nominal sizes with ribbed tails and hexagons for use at pressure

16、s not exceeding 1 550 kN/m 2(225 lbf/in 2 ). For assembly of coupling, see Figure 1. This document is applicable to couplings which have been designed primarily for aircraft refuelling purposes, but they may also be used for other general purposes. 2 Normative references The following documents, in

17、whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1982:1998, Copper and copper all

18、oys Ingots and castings EN ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1) EN ISO 228-2, Pipe threads where pressure-tight joints are not made on the threads - Part 2: Verification by means of limit gauges (

19、ISO 228-2) BS 1936-1, Undercuts and runouts for screw threads. Inch screw threads BS 1936-2, Undercuts and runouts for screw threads. Metric screw threads BS 2751, General purpose acrylonitrile-butadiene rubber compounds. Specification BS 3643-2:2007, ISO metric screw threads Specification for selec

20、ted limits of size 3 Information to be supplied by the purchaser It is essential that the purchaser states in the enquiry and order, the form of screw thread required (see Clause 8). 4 Designation of sizes of couplings The size by which the coupling is designated shall be the nominal bore of the hos

21、e with which it is to be used. 5 Materials The material used in the manufacture of the couplings shall be as follows: a) Gunmetal castings conforming to Specification CC 491 K of EN 1982:1998 b) Brass castings conforming to Specification CC 750 S of EN 1982:1998 6 Dimensions The dimensions of coupli

22、ngs and union nuts shall conform to those shown on Figure 2, Figure 3 and Figure 4 and in Table 1, Table 2 and Table 3. NOTE The illustrations in this Technical Specification are diagrammatic only, and are solely for the purpose of indicating where the specified dimensions apply. PD CEN/TS 16650:201

23、4 CEN/TS 16650:2014 (E) 5 7 Coupling finish The couplings shall be machined all over including the bores. All burrs and sharp edges shall be removed. 8 Screw threads The coupling assembly is given in Figure 1. The couplings shall be screwed with either: a) Whitworth BSP threads. The threads on the l

24、iner of the union nut (Figure 4 and Table 3) parallel threads as specified in EN ISO 228-1 and EN ISO 228-2. Thread undercuts shall conform to BS 1936-1. b) Metric threads. The threads on the liner of the union nut (Figure 5 and Table 4) shall conform to BS 3643-2:2007, Table 4, Tolerance class 6H (

25、medium fit) and BS 3643-2:2007, Table 5, Tolerance class 6g (medium fit). Thread undercuts shall conform to BS 1936-2 It is essential that the purchaser states in the enquiry and order which threads are required. 9 Washers Washers shall be made of specially selected leather or synthetic rubber in ac

26、cordance with BS 2751. 10 Bonding The couplings shall be fitted to the hose so that the electrical bonding, as specified in the relevant standard, is maintained for the hose assembly. 11 Hydrostatic test All couplings, when assembled without hose, shall be subjected to a hydrostatic test of 3 100 kN

27、/m 2(450 lbf/in 2 ). The test shall be applied after all machining operations have been completed. This test is for the purpose of locating flaws in the material after machining, and also to test the merits of the joint. When couplings are being assembled for the hydrostatic test, only the appropria

28、te standard wrench or spanner shall be used in tightening them. Use shall not be made of an extension on the handle of the wrench or spanner, or of other means to produce excessive tightness. Couplings conforming to this Technical Specification shall not show signs of leakage during this test by rea

29、son either of a defective joint or of other defects. 12 Identification marking Each set of couplings shall be legibly and permanently marked with: a) the manufacturers identification; b) the number and date of this Technical Specification; c) the following letters to indicate the type of screw threa

30、d on the couplings; 1) BSP for threads conforming to EN ISO 228-1 or EN ISO 228-2; 2) METRIC for threads conforming to BS 3643-2; d) the reference of the material type; PD CEN/TS 16650:2014 CEN/TS 16650:2014 (E) 6 e) the nominal size. Key 1 tail end: Male (see Figure 2) 2 union nut (see Figure 4) 3

31、screwed liner (see Figure 5) 4 tail end: Female (see Figure 3) Figure 1 Assembly of coupling Key 1 Whitworth (BSP) thread (see EN ISO 228-1 and EN ISO 228-2) Figure 2 Tail end: male (Machine all over) PD CEN/TS 16650:2014 CEN/TS 16650:2014 (E) 7 Table 1 Tail-end: male - hexagon (see Figure 2) Screw

32、thread B dia. C dia. D dia. G G 1H S W Nominal A XHexagon size of BSP thread coupling +0,25 0 0 -0,25 +0,25 0 0,25 0,75 0,75 Min. 0 -0,25 i.e. hose bore Nominal size in in mm mm mm mm mm mm mm mm 2 2 54 44,5 49,0 69,75 13 22 22 75 2 2 66,5 57 62 76 13 25 25 90 3 3 79,25 69,75 74,5 89 13 32 29 105 4

33、4 106,25 92 98 101,5 13 38 29 130 Figure 3 Tail-end: Female (Machine all over) Table 2 Tail-end: female (see Figure 3) B dia. C dia. D dia. F H L 2dia. V Nominal size 0 -0,25 0 -0,25 +0,25 0 Min. 0,75 0 -0,25 of coupling i.e. hose bore in mm mm mm mm mm mm mm 2 54 44,5 49 90 22 62 19 2 66,5 57 62 97

34、 25 78 21 3 79,25 69,75 74,5 111 32 90 22 4 106,25 92 98 125 38 117 24 PD CEN/TS 16650:2014 CEN/TS 16650:2014 (E) 8 Dimensions in millimetres Key 1 Whitworth (BSP) thread (see EN ISO 228-1 and EN ISO 228-2) 2 threads to BS 3643-2 Figure 4 Hex union nut and washer (Machine all over) Table 3 Union nut

35、: hexagon (see Figure 4) Screw thread A XISO metric thread N 1dia. O 1N P J 1J 4W Nominal size Whitworth (BSP) athread BS 3643-2 bTable 4 dia. dia. hexagon of coupling Tol. Class 6H i.e. hose (Medium fit) +0,25 0 +0,35 0 0,25 0 -1,5 0 -0,25 Nominal Minor dia. in in mm mm mm mm mm mm mm mm 2 2 M64 1,

36、5 62,376 62 9 61 45 13,5 32 75 2 2 M80 1,5 78,376 78 10 77 57 19 38 90 3 3 M95 2 92,835 90 11 89 70 22,25 43 105 4 4 M120 2 117,835 117 13 116 92 22,25 45 130 aEN ISO 228-1 and EN ISO 228-2 PD CEN/TS 16650:2014 CEN/TS 16650:2014 (E) 9 Dimensions in millimetres Key 1 threads to BS 3643-2 2 to crest o

37、f thread Figure 5 Screwed liner (Machine all over) The screwed liner shall be secured in position on union nut by pegging or by grab screwing. Table 4 Screwed liner for union nut (see Figure 5) Nominal size of coupling i.e. hose bore K R dia. S dia. O ISO Metric Thread (Medium) Tolerance Class 6 h B

38、S 3643- 2:2007, Table 5 0 -0,75 +0,25 0 0,25 +0,35 0 in mm mm mm mm 2 13 55 70 9 M64 1,5 2 15 68 87 10 M80 1,5 3 16 80 100 11 M95 2 4 18 107 127 13 M120 2 This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other

39、standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We

40、bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation proc

41、ess. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Custom

42、er Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from

43、other Standards Development Organizations, hard copies can be ordered from our Customer Services team. Subscriptions Our range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL

44、) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of

45、 standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BS

46、I Subscribing Member and the benefits of membership, please visit With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your do

47、cumentation is current. For further information, email . Revisions Our British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Stan

48、dard or other BSI publication please inform the Knowledge Centre. Copyright All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as t

49、he international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. De