BS MA 99-1-1985 Series 4 shipborne barges Specification for main dimensions《系列4船载驳船 主要尺寸规范规格》.pdf

《BS MA 99-1-1985 Series 4 shipborne barges Specification for main dimensions《系列4船载驳船 主要尺寸规范规格》.pdf》由会员分享，可在线阅读，更多相关《BS MA 99-1-1985 Series 4 shipborne barges Specification for main dimensions《系列4船载驳船 主要尺寸规范规格》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD MARINE SERIES CONFIRMED JULY 1999 BS MA 99-1: 1985 ISO6766:1984 Series4 shipborne barges Part1: Specification for main dimensions ISO title: Shipbuilding Shipborne barges, series4 Main dimensions UDC629.122.3:629.123.8*4BSMA99-1:1985 This BritishStandard, having been prepared under

2、the directionof the Shipbuilding andMarine Standards Committee, was published underthe authority of the BoardofBSI and comes intoeffecton 28February1985 BSI02-2000 The following BSI references relate to the work on this standard: Committee reference SME/14 Draft for comment83/70708 DC ISBN 0 580 143

3、72 4 Committees responsible for this BritishStandard The preparation of this BritishStandard was entrusted by the Shipbuilding and Marine Standards Committee (SME/-) to Technical Committee SME/14, upon which the following bodies were represented: Association of Master Lightermen and Barge Owners (Po

4、rt of London) British Tugowners Association British Waterways Board HM Customs and Excise Shiprepairers and Shipbuilders Independent Association Amendments issued since publication Amd. No. Date of issue CommentsBSMA99-1:1985 BSI 02-2000 i Contents Page Committees responsible Inside front cover Nati

5、onal foreword ii 1 Scope and field of application 1 2 Definition 1 3 Barge dimensions 1 4 Dimensions of principal constructional elements 1 5 Tolerances 2 Figure Main dimensions and dimensions of principal constructional elements 1 Table 1 Main barge dimensions 1 Table 2 Dimensions of principal cons

6、tructional elements 1 Table 3 Interchangeability tolerances 2BSMA99-1:1985 ii BSI 02-2000 National foreword This Part of BS MA99 has been prepared under the direction of the Shipbuilding and Marine Standards Committee and is identical with ISO6766:1984 “Shipbuilding Shipborne barges, series4 Main di

7、mensions” published by the International Organization for Standardization (ISO). ISO6766 was produced as a result of international discussion in which the UK took an active part. Terminology and conventions. The text of the International Standard has been approved as suitable for publication as a Br

8、itishStandard without deviation. Some terminology and certain conventions are not identical with those used in BritishStandards; attention is drawn especially to the following. Where the words “International Standard” appear, referring to this standard, they should be read as “BritishStandard”. A Br

9、itish Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a fr

10、ont cover, an inside front cover, pagesi andii, pages1 and 2 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BSMA99-1:1985 BSI 02-2000 1 1 Scope and field of applic

11、ation This International Standard lays down the main dimensions and the dimensions of the principal constructional elements of shipborne barges, series4. 2 Definition shipborne barge, series4 barge handled aboard a barge carrier by an elevator or by a system based on the floating-dock principle 3 Ba

12、rge dimensions The main dimensions of barges, series4, shall be in accordance with Table 1. 4 Dimensions of principal constructional elements The dimensions of the principal constructional elements are specified in Table 2. Table 1 Main barge dimensions Table 2 Dimensions of principal constructional

13、 elements Main dimensions Maximum draught in fresh water Maximum displacement Length Width Height Depth at ends Mid-depth overall L B H H 1 T D mm mm mm mm mm tonnes 18745 4750 2850 3460 2777 236 Dimensions in millimetres Distance between centres of supports Distance from centres of support Protrusi

14、on of supports below bottom longitudinally transversely diagonally to side to end A C D F E J 15850 4128 16379 311 1448 127 NOTEThe form of the hull shapes is presented schematically and is not specified by this International Standard. Figure Main dimensions and dimensions of principal constructiona

15、l elementsBSMA99-1:1985 2 BSI 02-2000 5 Tolerances Table 3 specifies the tolerances for those dimensions which determine the interchangeability of the barges with respect to their handling aboard a barge carrier. Table 3 Interchangeability tolerances NOTEDimensions for which tolerances are not speci

16、fied in this International Standard may be toleranced in accordance with national shipbuilding standards. Values in millimetres Tolerance on: L B A C 6 6 6 6blankBS MA99-1: 1985 ISO6766:1984 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body

17、responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest ame

18、ndments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be f

19、ound on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications

20、 should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a

21、 wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:020899

22、67111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright su

23、bsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by

24、any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.