BS MA 105-1-1987 Series 3 shipborne barges Specification for main dimensions《系列3船载驳船 主要尺寸规格》.pdf

《BS MA 105-1-1987 Series 3 shipborne barges Specification for main dimensions《系列3船载驳船 主要尺寸规格》.pdf》由会员分享，可在线阅读，更多相关《BS MA 105-1-1987 Series 3 shipborne barges Specification for main dimensions《系列3船载驳船 主要尺寸规格》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD MARINE SERIES CONFIRMED JULY1999 BS MA105-1: 1987 ISO6765:1985 Series3 shipborne barges Part 1: Specification for main dimensions ISO title: Shipbuilding Shipborne barges, series3 Maindimensions UDC 629.122.3:629.014.3BSMA105-1:1987 This BritishStandard, having been prepared under t

2、he directionof the Shipbuilding andMarine Standards Committee, was published underthe authority of the BoardofBSI and comes intoeffecton 31 July1987 BSI02-2000 The following BSI references relate to the work on this standard: Committee reference SME/14 Draft for comment83/70707DC ISBN 0 580 16012 2

3、Committees responsible for this BritishStandard The preparation of this BritishStandard was entrusted by the Shipbuilding and Marine Standards Committee (SME/-) to Technical Committee SME/14, upon which the following bodies were represented: Association of Master Lightermen and Barge Owners (Port of

4、 London) British Tugowners Association British Waterways Board HM Customs and Excise Shiprepairers and Shipbuilders Independent Association Amendments issued since publication Amd. No. Date of issue CommentsBSMA105-1:1987 BSI 02-2000 i Contents Page Committees responsible Inside front cover National

5、 foreword ii 1 Scope and field of application 1 2 Definition 1 3 Barge dimensions 1 4 Adjusting and securing components 1 5 Tolerances 3 Figure 1 Shipborne barge, series3 Main dimensions 1 Figure 2 Arrangement of the tie-down fittings 2 Figure 3 Arrangement of points of contact in a barge and of sec

6、uringdevicesina barge carrier 3 Table 1 Main barge dimensions 1 Table 2 Interchangeability tolerances 3BSMA105-1:1987 ii BSI 02-2000 National foreword This Part of BS MA105 has been prepared under the direction of the Shipbuilding and Marine Standards Committee and is identical with ISO6765:1985 “Sh

7、ipbuilding Shipborne barges, series3 Main dimensions”, published by the International Organization for Standardization (ISO). ISO6765 was produced as a result of international discussion in which the UK took an active part. Terminology and conventions. The text of the International Standard has been

8、 approved as suitable for publication as a BritishStandard without deviation. Some terminology and certain conventions are not identical with those used in BritishStandards; attention is drawn especially to the following. Where the words “International Standard” appear, referring to this standard, t

9、hey should be read as “Part of MA105”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Su

10、mmary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 to3 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BSMA105-1:1987

11、 BSI 02-2000 1 1 Scope and field of application This International Standard lays down the main dimensions and the dimensions of the principal constructional elements of shipborne barges, series3. 2 Definition shipborne barge, series3 barge handled aboard a barge carrier by an elevator or by a system

12、 based on the floating-dock principle 3 Barge dimensions The main dimensions of barges, series3, shall be in accordance with Table 1. The stationary equipment installed on the deck at fore and aft ends in all places shall nowhere project beyond the overall height. 4 Adjusting and securing components

13、 The adjusting and securing components include: a) bottom positioning angles; b) tie-down fittings for securing barges on the upper deck of a barge carrier; c) points of contact of securing devices (jacks) on the tween deck of a carrier. The arrangements are given in Figure 1, Figure 2 and Figure 3.

14、 Table 1 Main barge dimensions Main dimensions Distance between theoutboard edge of thepositioning angle andlongitudinal centreline plane Maximum draught in fresh water Maximum displacement Length Width Height Depth at ends Mid-depth overall (without positioning angles) L B H H 1 N T max D mm mm mm

15、mm mm mm tonnes 38250 11000 3900 5300 3407 3460 1300 NOTE 1The form of the hull shapes is presented schematically and is not specified by this International Standard. NOTE 2The length of the positioning angle should be not less than80% of the bottom length of a shipborne barge. NOTE 3The diameter of

16、 the positioning bitt is150mm. Figure 1 Shipborne barge, series3 Main dimensionsBSMA105-1:1987 2 BSI 02-2000 Figure 2 Arrangement of the tie-down fittingsBSMA105-1:1987 BSI 02-2000 3 5 Tolerances Table 2 specifies the tolerances for those dimensions which determine the interchangeability of the barg

17、es with respect to their handling aboard a barge carrier. Table 2 Interchangeability tolerances NOTEDimensions for which tolerances are not specified in this International Standard may be toleranced in accordance with national shipbuilding standards. Figure 3 Arrangement of points of contact in a ba

18、rge and of securing devices inabargecarrier Values in millimetres Tolerance on: L B H N 38 22 15 +0 5BS MA105-1: 1987 ISO6765:1985 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the

19、UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improv

20、e the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:0208996

21、7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001.

22、Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and interna

23、tional standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept

24、up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright

25、, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise w

26、ithout prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.