BS ISO IEC 11695-2-2015 Identification cards Optical memory cards Holographic recording method Dimensions and location of accessible optical area《识别卡 光学存储卡 全息记录方法 可到达光学区域的.pdf

《BS ISO IEC 11695-2-2015 Identification cards Optical memory cards Holographic recording method Dimensions and location of accessible optical area《识别卡 光学存储卡 全息记录方法 可到达光学区域的.pdf》由会员分享，可在线阅读，更多相关《BS ISO IEC 11695-2-2015 Identification cards Optical memory cards Holographic recording method Dimensions and location of accessible optical area《识别卡 光学存储卡 全息记录方法 可到达光学区域的.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication BS ISO/IEC 11695-2:2015 Identification cards Optical memory cards Holographic recording method Part 2: Dimensions and location of accessible optical areaBS ISO/IEC 11695-2:2015 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO/IEC 1169

2、5-2:2015. It supersedes BS ISO/IEC 11695-2:2008 which is withdrawn. NOTE: ISO/IEC have acknowledged that the supersession information listed in the ISO/IEC foreword to this document is inaccurate. The UK participation in its preparation was entrusted to Technical Committee IST/17, Cards and personal

3、 identification. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2015. Publ

4、ished by BSI Standards Limited 2015 ISBN 978 0 580 84446 1 ICS 35.240.15 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2015. Amendments/corrigenda issu

5、ed since publication Date Text affectedBS ISO/IEC 11695-2:2015 Identification cards Optical memory cards Holographic recording method Part 2: Dimensions and location of accessible optical area Cartes didentification Cartes mmoire optique Mthode denregistrement holographique Partie 2: Dimensions et e

6、mplacement de la zone optique accessible INTERNATIONAL STANDARD ISO/IEC 11695-2 Reference number ISO/IEC 11695-2:2015(E) Second edition 2015-04-01 ISO/IEC 2015 BS ISO/IEC 11695-2:2015ii ISO/IEC 2015 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2015 All rights reserved. Unless otherwise s

7、pecified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below o

8、r ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ISO/IEC 11695-2:2015(E)BS ISO/IEC 11695-2:2015ISO/IEC 11695-2:2015(E)Foreword iv In

9、troduction v 1 Scope .1 2 Normative references 1 3 Terms and definitions .1 4 Dimensions and location .1 4.1 Accessible optical area . 1 4.2 Dimensions R, S, T , U, V 2 4.2.1 Chip-type accessible optical area 3 4.2.2 Magnetic-stripe-type accessible optical area 4 4.3 Dimensions X, Y 4 4.4 Skew . 4 4

10、.5 Hologram size 4 4.6 Arrangement of multiple holograms 5 Bibliography 6 ISO/IEC 2015 All rights reserved iii Contents PageBS ISO/IEC 11695-2:2015ISO/IEC 11695-2:2015(E) Foreword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form th

11、e specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC techn

12、ical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. Th

13、e procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of document should be noted. This document was drafted in accordance with the editor

14、ial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. Details of any pate

15、nt rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For

16、 an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT), see the following URL: Foreword Supplementary information. The committee responsible for

17、this document is ISO/IEC JTC 1, Information technology, SC 17, Cards and personal identification. This second edition cancels and replaces the first edition (ISO/IEC 11695-1:2008), which has been technically revised. ISO/IEC 11695 consists of the following parts, under the general title Identificati

18、on cards Optical memory cards Holographic recording method: Part 1: Physical characteristics Part 2: Dimensions and location of accessible optical area Part 3: Optical properties and characteristicsiv ISO/IEC 2015 All rights reservedBS ISO/IEC 11695-2:2015ISO/IEC 11695-2:2015(E) Introduction This pa

19、rt of ISO/IEC 11695 is one of a series of International Standards defining the parameters for optical holographic memory cards and the use of such cards for the storage and interchange of digital data. These International Standards recognize the existence of different methods for recording and readi

20、ng information on optical memory cards, the characteristics of which are specific to the recording method employed. In general, these different recording methods will not be compatible with each other. Therefore, the standards are structured to accommodate the inclusion of existing and future record

21、ing methods in a consistent manner. This part of ISO/IEC 11695 is specific to optical memory cards using the holographic recording method. Characteristics which apply to other specific recording methods are found in separate standards documents. This part of ISO/IEC 11695 defines the dimensions and

22、location of accessible optical area and the extent of compliance with, addition to, and/or deviation from the relevant base document, ISO/IEC 11693-1. The International Organization for Standardization (ISO) and International Electrotechnical Commission (IEC) draw attention to the fact that it is cl

23、aimed that compliance with this part of ISO/IEC 11695 may involve the use of patents. The ISO and IEC take no position concerning the evidence, validity, and scope of these patent rights. The holders of these patent rights have assured the ISO and IEC that they are willing to negotiate licenses unde

24、r reasonable and non-discriminatory terms and conditions with applicants throughout the world. In this respect, the statements of the holders of these patent rights are registered with the ISO and IEC. Information may be obtained from: Certego GmbH Keltenring 12 82041 Oberhaching Germany Attention i

25、s drawn to the possibility that some of the elements of this part of ISO/IEC 11695 might be the subject of patent rights other than those identified above. ISO and IEC are not to be held responsible for identifying any or all such patent rights. ISO/IEC 2015 All rights reserved vBS ISO/IEC 11695-2:2

26、015BS ISO/IEC 11695-2:2015Identification cards Optical memory cards Holographic recording method Part 2: Dimensions and location of accessible optical area 1 Scope This part of ISO/IEC 11695 defines the dimensions and location of the accessible optical area of optical memory cards using the holograp

27、hic recording method. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced documen

28、t (including any amendments) applies. ISO/IEC 11693-1, Identification cards Optical memory cards Part 1: General characteristics ISO/IEC 11695-1, Identification cards Optical memory cards Holographic recording method Part 1: Physical characteristics ISO/IEC 11695-3, Identification cards Optical memo

29、ry cards Holographic recording method Part 3: Optical properties and characteristics 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO/IEC 11695-1, ISO/IEC 11695-3, and the following apply. 3.1 reference hologram hologram located at a defined position

30、on the accessible optical area of the holographic memory card, containing information concerning the location and content of further holograms on the card 3.2 track line running parallel to the longer reference edge of the card providing orientation for the storage of multiple holograms 3.3 referenc

31、e track track containing the reference hologram 4 Dimensions and location ISO/IEC 11695 part 2 applies to cards with a specified accessible optical area. 4.1 Accessible optical area The dimensions and location of the specified accessible optical area shall be as shown in Figure 1. INTERNATIONAL ST A

32、NDARD ISO/IEC 11695-2:2015(E) ISO/IEC 2015 All rights reserved 1BS ISO/IEC 11695-2:2015ISO/IEC 11695-2:2015(E) Dimensions in millimetres Reference edge A B U V S T Reference edge Accessible optical area X Y Reference track Hologram Radius of Curvature R A = 85,47 to 85,72 (ISO IEC 7810) B = 53,92 to

33、 54,02 (ISO IEC 7810) R, S, T, U, V see 4.2 X,Y see 4.3 NOTE Drawing not to scale Figure 1 Accessible optical area 4.2 Dimensions R, S, T , U, V This part of ISO/IEC 11695 defines two types of accessible optical area: one references a contact chip- type location and the other a magnetic-stripe-type

34、location (see Fig. 2 and Fig 3)2 ISO/IEC 2015 All rights reservedBS ISO/IEC 11695-2:2015ISO/IEC 11695-2:2015(E) 4.2.1 Chip-type accessible optical area Dimensions in millimetres R = 2,2 mm (radius of curvature) S = 8,5 mm T = 13,0 mm U = 4,1 mm V = 11,8 mm NOTE Drawing not to scale Figure 2 Chip-typ

35、e accessible optical area ISO/IEC 2015 All rights reserved 3BS ISO/IEC 11695-2:2015ISO/IEC 11695-2:2015(E) 4.2.2 Magnetic-stripe-type accessible optical area Dimensions in millimetres5,54 10,28 15 10 15,82 0,02 0,2 position of single hologram 53,92 - 54,03 0,68 0,84 85,47 85,72 R = not applicable S

36、= not applicable T = 85,47 mm to 85,72 mm U = 5,54 mm V = 10,28 mm NOTE Drawing not to scale Figure 3 Magnetic-stripe-type accessible optical area 4.3 Dimensions X, Y At location X,Y relative to the reference edges a reference hologram is placed (see figure 1). According to the accessible optical ar

37、ea as described in 4.2, this part of ISO/IEC 11695 defines the position for the reference hologram to be X = 15 mm, Y = 10 mm. 4.4 Skew The skew of the reference track relative to the horizontal reference edge of the card shall be less than or equal to 0,2. See Figure 1. 4.5 Hologram size The hologr

38、am size is not fixed, but shall be left to each industry user group to specify for those applications requiring interchange. Typical values of the size of a hologram ranges between 0.02 mm 2and 4 mm 2 . This part of ISO/IEC 11695 defines the hologram size to be 4 mm, therefore the size of the hologr

39、am (hx, hy) is defined to be hx = 2 mm, hy = 2 mm.4 ISO/IEC 2015 All rights reservedBS ISO/IEC 11695-2:2015ISO/IEC 11695-2:2015(E) 4.6 Arrangement of multiple holograms The optical area can contain data in form of one or more holograms. The location of the reference hologram is at location X, Y rela

40、tive to the reference edges of the card (see Fig. 1). If more than one hologram is located on the optical area of the card, holograms are arranged on the reference track or on tracks parallel to the reference track (see Fig. 1, Fig. 4). A minimum distance between the holograms has to be considered t

41、o avoid crosstalk from neighboring holograms when reading out one hologram. The distance (dx, dy) depends on the size of holograms (see 4.5) and has to be greater equal than the size of the hologram (hx, hy). This part of ISO/IEC 11695 defines the distance bet ween the holograms (dx, dy) to be dx =

42、2 mm, dy = 2 mm. xxx xxx h y h x d x d y d x h x d y h y Figure 4 Arrangement of multiple holograms ISO/IEC 2015 All rights reserved 5BS ISO/IEC 11695-2:2015ISO/IEC 11695-2:2015(E) Bibliography 1 ISO/IEC 7811-2, Identification cards Recording technique Part 2: Magnetic stripe Low coercivit y 2 ISO/I

43、EC 7811-6, Identification cards Recording technique Part 6: Magnetic stripe High coercivit y 3 ISO/IEC 7816-2, Identification cards Integrated circuit cards Part 2: Cards with contacts Dimensions and location of the contacts 4 ISO/IEC 7810, Identification cards Physical characteristics 5 ISO/IEC 103

44、73-1, Identification cards Test methods Part 1: General characteristics 6 ISO/IEC 10373-5, Identification cards Test methods Part 5: Optical memory cards6 ISO/IEC 2015 All rights reservedBS ISO/IEC 11695-2:2015BS ISO/IEC 11695-2:2015ISO/IEC 11695-2:2015(E) ISO/IEC 2015 All rights reserved ICS 35.240

45、.15 Price based on 6 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardization products are published

46、 by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.

47、The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can provide you with the kno

48、wledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and inter

49、national standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team. Subscriptions Our range of subscription services are designed to make using standards easier for you. For further