BS ISO IEC 11694-2-2012 Identification cards Optical memory cards Dimensions and location of the accessible optical area《识别卡 光记忆卡 线性记录方法 可访问光区域的尺寸规格和位置》.pdf

《BS ISO IEC 11694-2-2012 Identification cards Optical memory cards Dimensions and location of the accessible optical area《识别卡 光记忆卡 线性记录方法 可访问光区域的尺寸规格和位置》.pdf》由会员分享，可在线阅读，更多相关《BS ISO IEC 11694-2-2012 Identification cards Optical memory cards Dimensions and location of the accessible optical area《识别卡 光记忆卡 线性记录方法 可访问光区域的尺寸规格和位置》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwide NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Standards Publication BS ISO/IEC 11694-2:2012 Identification cards Optical memory cards Part 2: Dimensions and location of the accessible optical areaBS ISO/IEC 11694-2:2012 BRITISH STANDARD Nation

2、al foreword This British Standard is the UK implementation of ISO/IEC 11694-2:2012. It supersedes BS ISO/IEC 11694-2:2005 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee IST/17, Cards and personal identification. A list of organizations represented on

3、 this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012 ISBN 978 0 580 7492

4、2 3 ICS 35.240.15 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2012. Amendments issued since publication Date Text affectedBS ISO/IEC 11694-2:201

5、2Reference number ISO/IEC 11694-2:2012(E) ISO/IEC 2012INTERNATIONAL STANDARD ISO/IEC 11694-2 Fourth edition 2012-12-15 Identification cards Optical memory cards Part 2: Dimensions and location of the accessible optical area Cartes didentification Cartes mmoire optique Partie 2: Dimensions et emplace

6、ment de la zone optique accessible BS ISO/IEC 11694-2:2012 ISO/IEC 11694-2:2012(E) COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2012 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including pho

7、tocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Sw

8、itzerland ii ISO/IEC 2012 All rights reservedBS ISO/IEC 11694-2:2012 ISO/IEC 11694-2:2012(E) ISO/IEC 2012 All rights reserved iiiContents Page Foreword iv Introduction . v 1 Scope 1 2 Normative references 1 3 Terms and definitions . 1 4 Dimensions and location 1 4.1 General . 1 4.2 Accessible optica

9、l area . 1 4.2.1 Dimension C . 1 4.2.2 Dimension X . 1 4.2.3 Dimension Y . 2 4.2.4 Skew 2 Annex A (informative) Optional card layouts . 3 A.1 General . 3 A.2 Accessible optical area . 3 A.2.1 Location 3 A.2.2 Reference track 3 A.2.3 Size 3 A.2.4 Co-existence 3 Bibliography 4 BS ISO/IEC 11694-2:2012

10、ISO/IEC 11694-2:2012(E) iv ISO/IEC 2012 All rights reservedForeword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate i

11、n the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and no

12、n-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main

13、 task of the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies castin

14、g a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. ISO/IEC 11694-2 was prepared by Joint Technical Committee ISO/IEC JTC 1, Informatio

15、n technology, Subcommittee SC 17, Cards and personal identification. This fourth edition cancels and replaces the third edition (ISO/IEC 11694-2:2005), which has been technically revised. ISO/IEC 11694 consists of the following parts, under the general title Identification cards Optical memory cards

16、 Linear recording method: Part 1: Physical characteristics Part 2: Dimensions and location of the accessible optical area Part 3: Optical properties and characteristics Part 4: Logical data structures Part 5: Data format for information interchange for applications using ISO/IEC 11694-4, Annex B Par

17、t 6: Use of biometrics on an optical memory card BS ISO/IEC 11694-2:2012 ISO/IEC 11694-2:2012(E) ISO/IEC 2012 All rights reserved vIntroduction This part of ISO/IEC 11694 is one of a series of standards describing the parameters for optical memory cards and the use of such cards for the storage and

18、interchange of digital data. The standards recognize the existence of different methods for recording and reading information on optical memory cards, the characteristics of which are specific to the recording method employed. In general, these different recording methods will not be compatible with

19、 each other. Therefore, the standards are structured to accommodate the inclusion of existing and future recording methods in a consistent manner. This part of ISO/IEC 11694 is specific to optical memory cards using the linear recording method. Characteristics which apply to other specific recording

20、 methods shall be found in separate standards documents. This part of ISO/IEC 11694 defines the dimensions and location of the accessible optical area and the extent of compliance with, addition to, and/or deviation from the relevant base document, ISO/IEC 11693. The users attention is called to the

21、 possibility that compliance with this part of ISO/IEC 11694 may require use of an invention covered by patent rights and/or other material covered by copyrights. By publication of this part of ISO 11694, no position is taken with respect to the validity of this claim or of any patent rights or copy

22、rights in connection therewith. BS ISO/IEC 11694-2:2012BS ISO/IEC 11694-2:2012 INTERNATIONAL STANDARD ISO/IEC 11694-2:2012(E) ISO/IEC 2012 All rights reserved 1Identification cards Optical memory cards Part 2: Dimensions and location of the accessible optical area 1 Scope This part of ISO/IEC 11694

23、defines the dimensions and location of the accessible optical area of optical memory cards with ID-1 dimensions using the linear recording method. 2 Normative references There are no normative references in this document. 3 Terms and definitions 3.1 reference edge lower horizontal edge or left verti

24、cal edge, using the card orientation shown in Figure 1 3.2 reference track first track located nearest the horizontal reference edge of the card, as shown in Figure 1 4 Dimensions and location 4.1 General This part of ISO/IEC 11694 applies to cards containing only one accessible optical area. Option

25、al card layouts are described in Annex A. 4.2 Accessible optical area The dimensions and location of the accessible optical area shall be as shown in Figure 1. 4.2.1 Dimension C Dimension C, as shown by Figure 1, is not fixed by this part of ISO/IEC 11694, but shall be left to each industry user gro

26、up to specify for those applications requiring interchange. Dimension C shall never be less than 9,5 mm nor greater than 49,2 mm. 4.2.2 Dimension X Dimension X shall be 1,0 mm maximum (see Figure 1). BS ISO/IEC 11694-2:2012 ISO/IEC 11694-2:2012(E) 2 ISO/IEC 2012 All rights reserved4.2.3 Dimension Y

27、Dimension Y, as shown in Figure 1, shall be less than dimension D by at least 1,0 mm. 4.2.4 Skew The skew of the reference track relative to the horizontal reference edge of the card shall be less than or equal to 0,2 0 (see Figure 1). Dimensions in millimetres Accessible optical area Dimensions in

28、millimetres Reference Edge Reference Track Reference edge X X A D Y C B NOTE Drawing not to scale. Figure 1 Dimensions and location of the accessible optical area BS ISO/IEC 11694-2:2012 ISO/IEC 11694-2:2012(E) ISO/IEC 2012 All rights reserved 3Annex A (informative) Optional card layouts A.1 General

29、 This Annex specifies the dimensions and locations of the accessible optical area of optical memory cards using the linear recording method which may include other technologies in addition to the accessible optical area. A.2 Accessible optical area A.2.1 Location The accessible optical area can be l

30、ocated on either face of the card. A.2.2 Reference track The reference track can be at the “top“ or “bottom“ of the card. A.2.3 Size The size of the accessible optical area can be adjusted to accommodate other technologies included on the card. A.2.4 Co-existence The user shall refer to ISO/IEC 1169

31、3-2. Technologies located co-incident with the accessible optical area on either side of the card shall not interfere with the accessible optical area. BS ISO/IEC 11694-2:2012 ISO/IEC 11694-2:2012(E) 4 ISO/IEC 2012 All rights reservedBibliography 1 ISO/IEC 7810, Identification cards Physical charact

32、eristics 2 ISO/IEC 11693-1, Identification cards Optical memory cards General characteristics 3 ISO/IEC 11694-4, Identification cards Optical memory cards Linear recording method Part 4: Logical data structures 4 ISO/IEC 11693-2, Identification cards Optical memory cards Co-existence of optical memo

33、ry with other machine readable technologies BS ISO/IEC 11694-2:2012BS ISO/IEC 11694-2:2012 ISO/IEC 11694-2:2012(E) ICS 35.240.15 Price based on 4 pages ISO/IEC 2012 All rights reserved This page deliberately left blankBSI is the independent national body responsible for preparing British Standards a

34、nd other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited. British Standards Insti

35、tution (BSI) raising standards worldwide BSI 389 Chiswick High Road London W4 4AL UK Te l + 4 4 ( 0 ) 2 0 8 9 9 6 9 0 0 1 Fax +44 (0)20 8996 7001 Revisions British Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they po

36、ssess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity

37、of which can be found on the inside front cover. S i m i l a r y f o r P A S s , p l e a s e n o t i f y B S I C u s t o m e r S e r v i c e s . Te l : + 4 4 ( 0 ) 2 0 8 9 9 6 9 0 0 1 F a x : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 1 BSI offers BSI Subscribing Members an individual updating service called PLU

38、S which ensures that subscribers automatically receive the latest editions of British Standards and PASs. Te l : + 4 4 ( 0 ) 2 0 8 9 9 6 7 6 6 9 F a x : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 1 Email: Buying standards Yo u m a y b u y P D F a n d h a rd c o p y v e r s i o n s o f s t a n d a rd s d i re c

39、t l y u s i n g a credit card from the BSI Shop on the website In addition all orders for BSI, international and foreign standards publications can be addressed to BSI Customer Services. Te l : + 4 4 ( 0 ) 2 0 8 9 9 6 9 0 0 1 F a x : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 1 Email: In response to orders for

40、 international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Knowledge Centre. Te l : +

41、 4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 4 F a x : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 5 Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Te l

42、 : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 2 F a x : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 1 Email: Information regarding online access to British Standards and PASs via British Standards Online can be found at Further information about British Standards is available on the BSI website at www.bsi- Copyright All the

43、 data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to B

44、SI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BS

45、I. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department. Te l : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 7 0 Email: