BS ISO 9727-5-2007 Cylindrical cork stoppers - Physical tests - Determination of extraction force《圆柱形软木塞 物理试验 拔出力测定》.pdf

《BS ISO 9727-5-2007 Cylindrical cork stoppers - Physical tests - Determination of extraction force《圆柱形软木塞 物理试验 拔出力测定》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 9727-5-2007 Cylindrical cork stoppers - Physical tests - Determination of extraction force《圆柱形软木塞 物理试验 拔出力测定》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 9727-5:2007 Cylindrical cork stoppers Physical tests Part 5: Determination of extraction force ICS 55.100; 79.100 BS ISO 9727-5:2007 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 June 2007 BSI 2007 ISBN 978 0 580

2、52942 9 National foreword This British Standard was published by BSI. It is the UK implementation of ISO 9727-5:2007. The UK participation in its preparation was entrusted to Technical Committee PRI/81, Cork. A list of organizations represented on this committee can be obtained on request to its sec

3、retary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publication Amd. No. Date Comments Reference n

4、umber ISO 9727-5:2007(E)INTERNATIONAL STANDARD ISO 9727-5 First edition 2007-05-15 Cylindrical cork stoppers Physical tests Part 5: Determination of extraction force Bouchons cylindriques en lige Essais physiques Partie 5: Dtermination de la force dextraction BS ISO 9727-5:2007ii iii Foreword ISO (t

5、he International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical commit

6、tee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotech

7、nical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member

8、 bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying

9、 any or all such patent rights. ISO 9727-5 was prepared by Technical Committee ISO/TC 87, Cork. This first edition of ISO 9727-5, together with the other parts of ISO 9727:2007, cancels and replaces ISO 9727:1991, which has been technically revised. ISO 9727 consists of the following parts, under th

10、e general title Cylindrical cork stoppers Physical tests: Part 1: Determination of dimensions Part 2: Determination of mass and apparent density for agglomerated cork stoppers Part 3: Determination of humidity content Part 4: Determination of dimensional recovery after compression Part 5: Determinat

11、ion of extraction force Part 6: Determination of liquid tightness Part 7: Determination of dust content BS ISO 9727-5:2007 blank1 Cylindrical cork stoppers Physical tests Part 5: Determination of extraction force 1 Scope This part of ISO 9727 specifies a test method for determining the maximum force

12、 necessary to extract a cylindrical cork stopper. It is applicable to all types of cylindrical cork stoppers ready for use, intended to be completely inserted in the bottle neck (straight cork stoppers). 2 Normative references The following referenced documents are indispensable for the application

13、of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 633, Cork Vocabulary 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO

14、 633 and the following apply. 3.1 straight cork stopper ras de bague stopper which is completely introduced in the bottle neck, its superior end reaching the top border of the bottle 4 Materials 4.1 Acetone, for cleaning the glass tubes or the necks of the empty bottles. 5 Apparatus 5.1 Bottling mac

15、hine with 4 jaws, with a jaw-compression diameter regulated between 15,5 mm and 16 mm. 5.2 Glass tubes, with an internal diameter of 18,5 mm 0,2 mm or an internal diameter of (d 0,2) mm (where d is the bore diameter of the bottle intended to be used, measured at 3 mm from the top border of the bottl

16、e) or empty bottles whose bore characteristics will be specified and referred to in the test report. BS ISO 9727-5:20072 5.3 Corkscrew, with a helicoidal stick, having the following characteristics: useful length: W 40 mm, u 60 mm; internal diameter: W 3 mm, u 4 mm; external diameter: W 8,5 mm, u 10

17、 mm; wire diameter: W 2,7 mm, u 3,2 mm; thread: W 8 mm, u 11 mm. 5.4 Extraction device, operated by an electric engine, having a compression gauge sensor with a maximum resolution of 10 N, which moves in the parallel direction to the central axis of the stopper at a speed of 300 mm/min. 6 Test condi

18、tions 6.1 Environment The test shall be carried out in an environment with the following characteristics: temperature 21 C 4 C; relative humidity of air 60 % 20 %. 6.2 Cork stoppers 6.2.1 Temperature At the beginning of the test, confirm that the stoppers of the test sample are at a temperature of 2

19、1 C 4 C. 6.2.2 Humidity At the beginning of the test, confirm that the stoppers of the test sample are at a humidity of 6 % 2 %. When the humidity is not between 4 % and 8 %, the result of the humidity obtained shall be referred to in the test report. 7 Sampling From each lot, take the quantity of s

20、toppers that correspond to the sampling plan previously agreed between the interested parties. 8 Procedure Clean the glass tubes (5.2) or empty bottles with acetone (4.1) and let them dry. Put corks on empty bottles or tubes with the bottling machine (5.1). Carry out measurements one hour after cork

21、age. BS ISO 9727-5:20073 Introduce the corkscrew (5.3) into the central point of the cork-stopper end, the corkscrew axis being parallel to the cork-stopper central axis. Fix the tube or the bottle on the extraction device (5.4). Connect the corkscrew to the extraction device. Pull out the stopper a

22、t a speed of 30 cm/min. Read the maximum extraction force on the dial of the measuring unit and register the value obtained, in newtons, rounded off to the nearest 10 N. 9 Results The final test result is the arithmetic average of the results obtained with each stopper of the test sample, rounded of

23、f the nearest unity, and also the standard deviation rounded off to the nearest unity. 10 Test report The test report shall include the following information: a) a reference to this part of ISO 9727, referring to the type of support used (glass tube or bottle), as well as its dimensional characteris

24、tics; b) complete identification of the sample, including its type and origin; c) sampling report; d) results obtained; e) any deviation from this part of ISO 9727 that may have affected the results, namely the extraction speed if different from that specified in Clause 8. BS ISO 9727-5:2007BS ISO 9

25、727-5:2007 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions Britis

26、h Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity whil

27、e using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscrib

28、ers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI

29、 website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European

30、 and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email:

31、 infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membership

32、bsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, o

33、f the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior w

34、ritten permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.