BS ISO 8177-2015 Aerospace Omega clamps (saddle clamps) for fluid systems Dimensions《航空航天 流体系统用Ω形卡箍 (鞍型卡箍) 尺寸》.pdf

《BS ISO 8177-2015 Aerospace Omega clamps (saddle clamps) for fluid systems Dimensions《航空航天 流体系统用Ω形卡箍 (鞍型卡箍) 尺寸》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 8177-2015 Aerospace Omega clamps (saddle clamps) for fluid systems Dimensions《航空航天 流体系统用Ω形卡箍 (鞍型卡箍) 尺寸》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication BS ISO 8177:2015 Aerospace Omega clamps (saddle clamps) for fluid systems DimensionsBS ISO 8177:2015 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 8177:2015. It supersedes BS M 64:1987 which is withdrawn. The UK participation in it

2、s preparation was entrusted to Technical Committee ACE/69, Aerospace hydraulic systems, fluids and components. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. U

3、sers are responsible for its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015 ISBN 978 0 580 85849 9 ICS 49.080 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authorit

4、y of the Standards Policy and Strategy Committee on 30 June 2015. Amendments issued since publication Date Text affectedBS ISO 8177:2015 ISO 2015 Aerospace Omega clamps (saddle clamps) for fluid systems Dimensions Aronautique et espace Colliers en omga pour systmes de fluides Dimensions INTERNATIONA

5、L STANDARD ISO 8177 Third edition 2015-07-01 Reference number ISO 8177:2015(E)BS ISO 8177:2015ISO 8177:2015(E)ii ISO 2015 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced

6、 or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO

7、 copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.orgBS ISO 8177:2015ISO 8177:2015(E)Foreword iv 1 Scope . 1 2 Normative references 1 3 Field of application 1 4 Field of use 1 5 Description . 1 6 Dime

8、nsions . 2 ISO 2015 All rights reserved iii Contents PageBS ISO 8177:2015ISO 8177:2015(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried ou

9、t through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO co

10、llaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different app

11、roval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the

12、 subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any

13、 trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in t

14、he Technical Barriers to Trade (TBT), see the following URL: Foreword Supplementary information. The committee responsible for this document is ISO/TC 20, Aircraft and space vehicles, SC 10, Aerospace fluid systems and components. This third edition cancels and replaces the second edition (ISO 8177:

15、1987), which constitutes a minor revision.iv ISO 2015 All rights reservedBS ISO 8177:2015INTERNATIONAL ST ANDARD ISO 8177:2015(E) Aerospace Omega clamps (saddle clamps) for fluid systems Dimensions 1 Scope This International Standard specifies maximum and minimum dimensions for omega clamps (saddle

16、clamps) installed by means of two bolts with nominal diameters of 5 mm. The specified dimensions define a dimensional envelope. This International Standard shall not be considered as an inter-changeability standard. The tolerances for each type of clamp are to be defined in the parts standards drawi

17、ngs. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any

18、amendments) applies. ISO 6771, Aerospace Fluid systems and components Pressure and temperature classifications 3 Field of application These clamps are intended for the installation, support and guiding of rigid tubing or hose assemblies used in aerospace equipment. NOTE Omega clamps (saddle clamps)

19、may also be used for other equipment, e.g. electrical cables or looms. 4 Field of use Omega clamps (saddle clamps) are classified into six types according to the temperature range in which they are intended to be used (see Table 1). Table 1 Types of omega (saddle) clamps Clamp type Temperature range

20、 a min. max. 1 55 +70 2 55 +135 3 55 +200 4 55 +320 5 55 +400 6 55 +650 a See ISO 6771. 5 Description The omega clamp (saddle clamp) is a “multi-component”-type clamp. It consists of a top band and a base contoured to the tubing. Mounting holes in the top band align with holes in the base on install

21、ation. This ISO 2015 All rights reserved 1BS ISO 8177:2015ISO 8177:2015(E) clamp is designed for single tubing installation, and can be provided as a metallic support only or with a plastomer or elastomer cushion or sheathing, as specified in the parts standard. 6 Dimensions The omega clamp (saddle

22、clamp) shall be in accordance with the figure and Table 2. The shape of clamp illustrated in the figure does not purport to be the exact shape of the manufactured clamp. Table 2 only specifies those dimensions required to define the maximum envelope and the proper location of the tube relative to th

23、e mounting plane and fastening points. Key 1 tube opening Figure 1 Maximum envelope dimensions for omega clamps (saddle clamps) Table 2 a Nominal diameter of tube DN Dimensions in millimetres Nominal diameter of tube DN b A B c D E F G H L c min. max. min. max. max. min. max. max. min. max. max. 14

24、36,5 37, 3 7, 8 11,8 2,5 8,1 5,8 2,2 5,2 5,5 19 16 38,5 39,3 8,8 12,8 2,5 8,1 5,8 2,2 5,2 5,5 19 18 40,5 41,3 9,8 13,8 2,5 8,1 5,8 2,2 5,2 5,5 19 20 42,5 43,3 10,8 14,8 2,5 8,1 5,8 2,2 5,2 5,5 19 22 44,5 45,3 11,8 15,8 2,5 8,1 5,8 2,2 5,2 5,5 19 25 49 49,8 13,7 17,9 3,3 8,8 6,6 2,7 5,2 5,5 21 aAll d

25、imensions in this table apply with the tube assembled in the tightened clamp. bDiameters DN 14, 18, 22, 28, 36, 45, 56, 70, and 90 are non-preferred sizes for tubing in fluid systems. cThis dimension is an overall dimension which includes metal width and cushion or sheathing.2 ISO 2015 All rights re

26、servedBS ISO 8177:2015ISO 8177:2015(E) Nominal diameter of tube DN b A B c D E F G H L c min. max. min. max. max. min. max. max. min. max. max. 28 52 52,8 15,2 19,4 3,3 8,8 6,6 2,7 5,2 5,5 21 32 56 56,8 17, 2 21,4 3,3 8,8 6,6 2,7 5,2 5,5 21 36 60 60,8 19,2 23,4 3,3 8,8 6,6 2,7 5,2 5,5 21 40 64 64,8

27、21,2 25,4 3,3 8,8 6,6 2,7 5,2 5,5 21 45 69 69,8 23,7 27,9 3,3 8,8 6,6 2,7 5,2 5,5 21 50 74 74,8 26,2 30,4 3,3 8,8 6,6 2,7 5,2 5,5 21 56 81,4 82,2 29,5 33,8 4 9,5 6,6 3,3 5,2 5,5 24 63 88,4 89,2 33 37, 3 4 9,5 6,6 3,3 5,2 5,5 24 70 95,4 96,2 36,5 40,8 4 9,5 6,6 3,3 5,2 5,5 24 80 105,4 106,2 41,5 45,8

28、 4 9,5 6,6 3,3 5,2 5,5 24 90 115,4 116,2 46,5 50,8 4 9,5 6,6 3,3 5,2 5,5 24 100 125,4 126,2 51,5 55,8 4 9,5 6,6 3,3 5,2 5,5 24 aAll dimensions in this table apply with the tube assembled in the tightened clamp. bDiameters DN 14, 18, 22, 28, 36, 45, 56, 70, and 90 are non-preferred sizes for tubing i

29、n fluid systems. cThis dimension is an overall dimension which includes metal width and cushion or sheathing.Table 2 (continued) ISO 2015 All rights reserved 3BS ISO 8177:2015ISO 8177:2015(E) ISO 2015 All rights reserved ICS 49.080 Price based on 3 pagesThis page deliberately left blankBSI is the na

30、tional body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited. British Standards Institution (BSI) BSI Group

31、 Headquarters 389 Chiswick High Road London W4 4AL UK About us We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions. The knowledge embodied in our standards has been carefully assembled in

32、a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can provide you with the knowledge that your organization needs to succeed. Find out more about Brit

33、ish Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also b

34、e purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team. Subscriptions Our range of subscription services are designed to make using standards easier for you. For further information on ou

35、r subscription products go to With British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards devel

36、opments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards whe

37、n theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With upd

38、ates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email . Revisions Our British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your busi

39、ness. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre. Copyright All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some perso

40、n or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored

41、in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department. Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 845 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW