BS ISO 8137-1997 Hydraulic fluid power - Single rod cylinders 250 bar (25 MPa) series - Port dimensions《液压流体动力 250巴(25MPa)系列单杆汽缸 油口尺寸》.pdf

《BS ISO 8137-1997 Hydraulic fluid power - Single rod cylinders 250 bar (25 MPa) series - Port dimensions《液压流体动力 250巴(25MPa)系列单杆汽缸 油口尺寸》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 8137-1997 Hydraulic fluid power - Single rod cylinders 250 bar (25 MPa) series - Port dimensions《液压流体动力 250巴(25MPa)系列单杆汽缸 油口尺寸》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 8137:1986 Hydraulic fluid power Single rod cylinders, 250bar (25 MPa) series Port dimensions ICS 23.100.20BSISO 8137:1986 This British Standard, having been prepared under the directionof the Engineering SectorBoard, was published underthe authority of the Standards Board and

2、 comes intoeffect on 15 June 1997 BSI 02-1999 ISBN 0 580 27548 5 National foreword This British Standard reproduces verbatim ISO8137:1986 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Committee MCE/18, Fluid power systems and compon

3、ents, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promu

4、lgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the se

5、ction entitled “International Standards Correspondence Index”, or using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application.

6、Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theISO title page, page ii, pages 1 and 2 and a back cover. This standard has been updated (see copyright date)

7、 and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSISO 8137:1986 BSI 02-1999 i Contents Page National foreword Inside front cover Foreword ii 0 Introduction 1 1 Scope and fiel

8、d of application 1 2 References 1 3 Definitions 1 4 Dimensions 1 5 Bore sizes 1 6 Identification statement 1 Table Port and flange sizes 2ii blankBS ISO8137:1986 ii BSI 02-1999 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (I

9、SO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, gov

10、ernmental and non-governmental, in liaison with ISO, also take part in the work. Draft International Standards adopted by the technical committees are circulated to the member bodies for approval before their acceptance as International Standards by the ISO Council. They are approved in accordance w

11、ith ISO procedures requiring at least 75% approval by the member bodies voting. International Standard ISO8137 was prepared by Technical Committee ISO/TC 131, Fluid power systems. Users should note that all International Standards undergo revision from time to time and that any reference made herein

12、 to any other International Standard implies its latest edition, unless otherwise stated. Descriptors: Hydraulic fluid power, hydraulic equipment, hydraulic cylinders, single rod cylinders, dimensions, interchangeability.BSISO8137:1986 BSI 02-1999 1 0 Introduction In hydraulic fluid power systems, p

13、ower is transmitted and controlled through a fluid (liquid or gas) under pressure within an enclosed circuit. One component of such systems is the fluid power cylinder. This is a device which converts power into linear mechanical force and motion. It consists of a movable element, i.e. a piston and

14、piston rod, operating within a cylindrical bore. 1 Scope and field of application This International Standard establishes port dimensions 1)for 250bar 2)(25 MPa) series cylinders as required for interchangeability of commonly used hydraulic cylinders. NOTEThis International Standard allows manufactu

15、rers of hydraulic equipment freedom in design of metric cylinders; it does not restrict technical development but provides basic guidelines. 2 References ISO 3320, Fluid power systems and components Cylinder bore and piston rod diameter Metric series. ISO 5598, Fluid power systems and components Voc

16、abulary. ISO 6022, Hydraulic fluid power Single rod cylinders Mounting dimensions 250bar (25000kPa) series. ISO 6149, Fluid power systems and components Metric ports Dimensions and design. ISO 6162, Hydraulic fluid power Flange connections Four-bolt split flanges rated for normal duty applications P

17、N 35 to PN 415 (3,5 to 41,5 MPa) Dimensions. 3) ISO 6164, Hydraulic fluid power Flange connections Four-bolt, one-piece square flanges rated for normal duty applications PN 250 and PN 400 (25 MPa and 40 MPa) Dimensions. 3) 3 Definitions For the purposes of this International Standard, the definition

18、s given in ISO5598 and the following definitions apply. 3.1 cylinder a device which converts fluid power into linear mechanical force and motion 3.2 cylinder bore the internal diameter of the cylinder 3.3 port an internal or external terminus of a passage in a component 4 Dimensions Port sizes and d

19、imensions for cylinders manufactured in accordance with ISO6022 shall be selected from the table. 5 Bore sizes The following bore sizes 4)are included in this250bar (25MPa) series: 50 63 80 100 125 160 200 250 320 400 500 mm 6 Identification statement (Reference to this International Standard) Use t

20、he following statement in test reports, catalogues and sales literature when electing to comply with this International Standard: “Port dimensions selected in accordance with ISO8137, Hydraulic fluid power Single rod cylinders, 250bar (25MPa) series Port dimensions.” 1) This International Standard p

21、ermits all ISO approved ports that are appropriate to fluid power applications. 2) 1 bar = 0,1 MPa = 10 5Pa; 1 Pa = 1 N/m 2 3) At present at the stage of draft. 4) Selected from ISO3320.BSISO 8137:1986 2 BSI 02-1999 Table Port and flange sizes Dimensions in millimetres Bore ISO 6149 Port ISO 6164 Sq

22、uare flange ISO 6162 Rectangular flange EE EC min. Nominal flange size DN FF EA 0,25 ED Nominal flange size DN FF EA 0,25 EB 0,25 ED 50 M22 1,5 12 63 80 M27 2 16 13 15 29,7 M8 1,25 13 12,7 17,50 38,10 M8 1,25 100 125 M33 2 20 19 20 35,3 M8 1,25 19 19,1 22,25 47,65 M10 1,5 160 200 M42 2 25 25 25 43,8

23、 M10 1,5 25 25,4 26,20 52,35 M10 1,5 250 320 M50 2 32 32 32 51,6 M12 1,75 32 31,8 30,20 58,70 M12 1,75 400 500 M60 2 38 38 38 60 M14 2 38 38,1 35,70 69,85 M14 2 0 1,5 0 1,5 3 blankBSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

24、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presen

25、ts the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI

26、to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000

27、. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. T

28、el: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on nationa

29、l, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscri

30、bing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publica

31、tions. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, pho

32、tocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.