BS ISO 6953-1-2015 en_6094 Pneumatic fluid power Compressed air pressure regulators and filter-regulators Main characteristics to be included in literature from suppliers.pdf

《BS ISO 6953-1-2015 en_6094 Pneumatic fluid power Compressed air pressure regulators and filter-regulators Main characteristics to be included in literature from suppliers.pdf》由会员分享，可在线阅读，更多相关《BS ISO 6953-1-2015 en_6094 Pneumatic fluid power Compressed air pressure regulators and filter-regulators Main characteristics to be included in literature from suppliers.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication BS ISO 6953-1:2015 Pneumatic fluid power Compressed air pressure regulators and filter-regulators Part 1: Main characteristics to be included in literature from suppliers and product- marking requirementsBS ISO 6953-1:2015 BRITISH STANDARD National foreword This British Sta

2、ndard is the UK implementation of ISO 6953-1:2015. It supersedes BS ISO 6953-1:2000 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MCE/18/-/5, Control components. A list of organizations represented on this committee can be obtained on request to its

3、 secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015 ISBN 978 0 580 76274 1 ICS 23.100.50 Compliance with a British Stand

4、ard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2015. Amendments/corrigenda issued since publication Date T e x t a f f e c t e dBS ISO 6953-1:2015 ISO 2015 Pneumatic fluid power Com

5、pressed air pressure regulators and filter- regulators Part 1: Main characteristics to be included in literature from suppliers and product- marking requirements Transmissions pneumatiques Rgulateurs de pression et filtres- rgulateurs pour air comprim Partie 1: Principales caractristiques inclure da

6、ns la documentation des fournisseurs et exigences de marquage du produit INTERNATIONAL STANDARD ISO 6953-1 Third edition 2015-03-01 Reference number ISO 6953-1:2015(E)BS ISO 6953-1:2015ISO 6953-1:2015(E)ii ISO 2015 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2015 All rights reserved. Unless

7、 otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the add

8、ress below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 6953-1:2015ISO 6953-1:2015(E)Foreword iv Introduction v 1 Scope .

9、 1 2 Normative references 1 3 Terms and definitions . 2 4 Technical requirements 2 4.1 General . 2 4.2 General characteristics . 3 4.2.1 General dimensions . 3 4.2.2 Port forms 5 4.2.3 Rated pressure . 5 4.2.4 Range of operating temperatures . 5 4.3 Particular requirements 5 4.3.1 General 5 4.3.2 Ad

10、justable pressure ranges (outlet regulated pressure) 5 4.3.3 Flow-pressure characteristics 6 4.3.4 Pressure regulation characteristic . 7 4.3.5 Pilot pressure/regulated pressure characteristics. 7 4.3.6 Repeatability (optional characteristic) 9 4.3.7 Resolution in the case of pilot operated regulato

11、r with air bleed . 9 4.3.8 Maximum air consumption at null forward flow rate or relief flow rate for pilot operated regulator with air bleed . 9 4.3.9 Useful retention capacity of the reservoir . 9 4.3.10 Filter-regulator draining devices . 9 4.3.11 Materials of construction 9 5 Operation and mainte

12、nance 10 6 Marking .10 7 Identification statement (Reference to ISO 6953) .10 Annex A (informative) Port forms from ISO 1179-1:1981 11 Bibliography .12 ISO 2015 All rights reserved iii Contents PageBS ISO 6953-1:2015ISO 6953-1:2015(E) Foreword ISO (the International Organization for Standardization)

13、 is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be repre

14、sented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to deve

15、lop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO

16、/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during

17、the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meani

18、ng of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT), see the following URL: Foreword Supplementary information. The committee responsible for this document is ISO/TC 131,

19、 Fluid power systems, Subcommittee SC 5, Control products and components. This third edition cancels and replaces the second edition (ISO 6953-1:2000), which has been technically revised. It also incorporates ISO 6953-1:2000/Cor 1:2006. ISO 6953 consists of the following parts, under the general tit

20、le Pneumatic fluid power Compressed air pressure regulators and filter-regulators: Part 1: Main characteristics to be included in the suppliers literature and product-marking requirements Part 2: Test methods to determine the main characteristics to be included in suppliers literature Part 3: Altern

21、ative test methods for measuring the flow-rate characteristics of pressure regulatorsiv ISO 2015 All rights reservedBS ISO 6953-1:2015ISO 6953-1:2015(E) Introduction In pneumatic fluid power systems, power is transmitted and controlled through a gas under pressure within a circuit. When pressure red

22、uction or pressure regulation is required, regulators and filter-regulators are components designed to maintain the pressure of the gas at an approximately constant level. It is therefore necessary to know some performance characteristics of these components in order to determine their suitability f

23、or an application. ISO 2015 All rights reserved vBS ISO 6953-1:2015BS ISO 6953-1:2015Pneumatic fluid power Compressed air pressure regulators and filter-regulators Part 1: Main characteristics to be included in literature from suppliers and product-marking requirements 1 Scope This part of ISO 6953

24、specifies which characteristics of compressed air pressure regulators are to be included in literature from their suppliers. It also applies to filter-regulators. This part of ISO 6953 applies to manually controlled direct operated types (with or without relieving mechanism), manually controlled int

25、ernal pilot operating types (e.g. nozzle flapper), and external pilot operated types. In addition, it specifies the product marking requirements for pressure regulators and filter-regulators. This part of ISO 6953 is applicable to compressed air pressure regulators with a rated inlet pressure of up

26、to 2 500 kPa (25 bar) and an outlet adjustment pressure of up to 1 600 kPa (16 bar); and to filter-regulators with rated inlet and outlet pressures of up to 1 600 kPa (16 bar), in which the major contaminants are removed by mechanical means. NOTE 1 1 bar = 0,1 MPa = 10 5Pa; 1 MPa = 1 N/mm 2 . The ra

27、ted pressure should be selected from the preferred pressures listed in ISO 2944. NOTE 2 The main characteristics to be included in the suppliers literature related to electrically modulated pneumatic continuous pressure control valves are specified in ISO 10094-1. 2 Normative references The followin

28、g documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 7-1:1994, Pipe

29、threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation ISO 2944, Fluid power systems and components Nominal pressures ISO 5598, Fluid power systems and components Vocabulary ISO 5782-2:1997, Pneumatic fluid power Compressed-air filters Part 2: Test

30、 methods to determine the main characteristics to be included in suppliers literature ISO 6358-1, Pneumatic fluid power Determination of flow-rate characteristics of components using compressible fluids Part 1: General rules and test methods for steady-state flow ISO 6953-2:2015, Pneumatic fluid pow

31、er Compressed air pressure regulators and filter-regulators Part 2: Test methods to determine the main characteristics to be included in literature from suppliers INTERNATIONAL ST ANDARD ISO 6953-1:2015(E) ISO 2015 All rights reserved 1BS ISO 6953-1:2015ISO 6953-1:2015(E) ISO 10094-1, Pneumatic flui

32、d power Electro-pneumatic pressure control valves Part 1: Main characteristics to include in the suppliers literature ISO 11727, Pneumatic fluid power Identification of ports and control mechanisms of control valves and other components 3 Terms and definitions For the purposes of this part of ISO 69

33、53, the terms and definitions given in ISO 5598, ISO 6358-1, ISO 10094-1, and the following apply. 3.1 compressed air pressure regulator component designed to maintain compressed air pressure, approximately constant within an enclosed circuit despite variation in operating flow rate and inlet pressu

34、re 3.2 relieving pressure regulator pressure regulator equipped with an unloading device that opens if the regulated pressure exceeds the original setting by a sufficient degree, and exhausts a limited flow rate of air from the outlet circuit to the atmosphere 3.3 filter-regulator device that combin

35、es the filter and regulator onto one body as a single unit Note 1 to entry: In such a device, the filter is always on the upstream side of the regulator. 3.4 pilot-operated regulator with air bleed regulator designed to minimize the variation of regulated pressure from its set point during flow, usi

36、ng a pilot supply that continuously flows through the pilot chamber and is exhausted 3.5 flow-pressure characteristic curve graphical representation of the relationship between the regulated pressure and the forward flow rate or the relief flow rate while the outlet set pressure and the inlet pressu

37、re are maintained constant 3.5.1 forward flow/pressure characteristic curve flow/pressure characteristic curve in accordance with 3.5 only for the forward flow rate 3.5.2 relief flow/pressure characteristic curve flow/pressure characteristic curve in accordance with 3.5 only for the relief flow rate

38、 3.6 pressure regulation characteristic curve graphical representation of regulated pressure variation caused by changes in inlet (supply) pressure, at a constant small air flow rate and low regulated pressure 4 Technical requirements 4.1 General Descriptive literature covering compressed air pressu

39、re regulators and filter-regulators shall include the following characteristics given in 4.2 and 4.3.2 ISO 2015 All rights reservedBS ISO 6953-1:2015ISO 6953-1:2015(E) 4.2 General characteristics 4.2.1 General dimensions The dimensions shown on Figure 1 shall be given in millimetres. For ports, see

40、4.2.2. ISO 2015 All rights reserved 3BS ISO 6953-1:2015ISO 6953-1:2015(E) Key A maximum overall width B maximum installation height below the port centre line C maximum overall depth, excluding pressure gauge D distance between the faces of the compressed air connection (inlet/outlet) E maximum heig

41、ht above the port centre line F a maximum installation depth from the port centre line G maximum dimension of the regulated pressure adjusting device H minimum clearance from the port centre line to permit dismantling J a distance between mounting holes K a distance between the port centre line and

42、mounting holes L a minimum recommended diameter and length of mounting holes M a panel mounting thread N a panel mounting height above the port centre line P a maximum panel thickness Q b distance between the port centre line to gage port V drain hole description W port description X b pilot port de

43、scription Y pressure gauge port description NOTE a dimensions, F, J, K, L, M, N, and P shall be indicated only if the device has provisions for mounting; b optional Figure 1 Dimensions of compressed air regulators and filter-regulators4 ISO 2015 All rights reservedBS ISO 6953-1:2015ISO 6953-1:2015(E

44、) 4.2.2 Port forms Port forms should be selected from ISO 16030 or ISO 1179 (all parts) for ports with pipe parallel threads, or from ISO 7-1 for ports with pipe-tapered threads. The connecting interface for flange-mounted designs can be plain ported and counter bored to accept O-rings. For certain

45、applications and connections, other port forms can be employed. NOTE Annex A describes thread forms from the former ISO 1179:1981. 4.2.3 Rated pressure Compressed air pressure regulators and filter-regulators shall be classified according to their rated pressure, selected from ISO 2944. The rated pr

46、essure shall be verified using the test procedure specified in ISO 6953-2: 2015, Clause 6. This procedure verifies the pressure rating of the pressure-containing envelope but does not cover the limitation that can be imposed by the diaphragm. The range of duties and sensitivities of the diaphragm us

47、ed vary widely and their strength can be limited to achieve the accuracy required by the application. 4.2.4 Range of operating temperatures 4.2.4.1 The temperature range in which the material and the operation of the pressure regulator and filter-regulator are not impaired shall be stated. 4.2.4.2 O

48、ther combinations of pressure and temperature ratings for optional designs that could require a different rating shall be specified. 4.3 Particular requirements 4.3.1 General The data provided by the supplier shall assist the user in selecting the compressed air pressure regulator and filter-regulat

49、or best suited for the particular application. 4.3.2 Adjustable pressure ranges (outlet regulated pressure) The upper limit of the recommended adjustable pressure range should normally be chosen from the following preferred ranges but not to exceed the inlet rated pressure: up to 100 kPa (1 bar); up to 200 kPa (2 bar); up to 400 kPa (4 bar); up to 800 kPa (8 bar); up to 1 000 kPa (10 bar); up to 1 600 kPa (16 bar). Special ranges can also be available. The adjustability of th