BS ISO 96-2-2009 en_2101 Textile machinery and accessories - Rings and travellers for ring spinning and ring twisting frames - HZ- and J-rings and their travellers《纺织机械和附件 环锭细纱机和环.pdf

《BS ISO 96-2-2009 en_2101 Textile machinery and accessories - Rings and travellers for ring spinning and ring twisting frames - HZ- and J-rings and their travellers《纺织机械和附件 环锭细纱机和环.pdf》由会员分享，可在线阅读，更多相关《BS ISO 96-2-2009 en_2101 Textile machinery and accessories - Rings and travellers for ring spinning and ring twisting frames - HZ- and J-rings and their travellers《纺织机械和附件 环锭细纱机和环.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO 96-2:2009 ICS 59.120.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Textile machinery and accessories Rings and travellers for ring spinning and ring twisting frames Part 2: HZ- and J-rings and their travellersThis British Standard was published und

2、er the authority of the Standards Policy and Strategy Committee on 30 September 2009 BSI 2009 ISBN 978 0 580 56362 1 Amendments/corrigenda issued since publication Date Comments BS ISO 96-2:2009 National foreword This British Standard is the UK implementation of ISO 96-2:2009. It supersedes BS ISO 9

3、6-2:1992 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee TCI/33, Textile machinery. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provi

4、sions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations.BS ISO 96-2:2009Reference number ISO 96-2:2009(E) ISO 2009INTERNATIONAL STANDARD ISO 96-2 Second edition 2009-03-01 Textile machinery and accessori

5、es Rings and travellers for ring spinning and ring twisting frames Part 2: HZ- and J-rings and their travellers Matriel pour lindustrie textile Anneaux et curseurs pour machines filer et retordre Partie 2: Anneaux HZ et J et leurs curseurs BS ISO 96-2:2009 ISO 96-2:2009(E) PDF disclaimer This PDF fi

6、le may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the

7、 responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-c

8、reation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO

9、 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the

10、country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedBS ISO 96-2:2009 ISO 96-2:2009(E) ISO 2009 All rights reserved iii Foreword IS

11、O (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical co

12、mmittee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electro

13、technical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the me

14、mber bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identif

15、ying any or all such patent rights. ISO 96-2 was prepared by Technical Committee ISO/TC 72, Textiles machinery and accessories, Subcommittee SC 1, Spinning preparatory, spinning, twisting and winding machinery and accessories. This second edition cancels and replaces the first edition (ISO 96-2:1992

16、), which has been technically revised. ISO 96 consists of the following parts, under the general title Textile machinery and accessories Rings and travellers for ring spinning and ring twisting frames: Part 1: Flange rings T and SF and their travellers Part 2: HZ- and J-rings and their travellers BS

17、 ISO 96-2:2009BS ISO 96-2:2009 INTERNATIONAL STANDARD ISO 96-2:2009(E) ISO 2009 All rights reserved 1 Textile machinery and accessories Rings and travellers for ring spinning and ring twisting frames Part 2: HZ- and J-rings and their travellers 1 Scope This part of ISO 96 specifies the principal dim

18、ensions of HZ- and J-rings, and the mass and tolerance on the mass, of the appropriate travellers for HZ- and J-rings employed on ring spinning and ring twisting machines. It also specifies the method of designation of the travellers. 2 Normative references The following referenced documents are ind

19、ispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3, Preferred numbers Series of preferred numbers 3 Principal dimensions of HZ- and J-ri

20、ngs The principal dimensions of HZ- and J-rings are illustrated in Figure 1 and Figure 2, respectively, and specified in Table 1. Figure 1 Example of an HZ-ring (vertical ring) BS ISO 96-2:2009 ISO 96-2:2009(E) 2 ISO 2009 All rights reservedFigure 2 Example of a J-ring (conical ring) Table 1 Ring di

21、mensions Dimensions in millimetres Ring type HZ J inside diameter Tolerance of fitting diameter d 1height height d tolerance ah h 0,1 0 +0,1 0 +45 48 50 6,3 55 60 9,5 65 70 10,3 75 80 0 0,25 11,1 9,1 90 100 16,7 110 125 0 0,32 25,4 11,1 140 150 160 0 0,4 38,1 17,4 180 200 200 0 0,55 aThe tolerance r

22、efers to the diameter d 1 , excluding any ovality. BS ISO 96-2:2009 ISO 96-2:2009(E) ISO 2009 All rights reserved 3 4 Travellers 4.1 Examples of travellers appropriate for HZ- and J-rings are shown in Figures 3 and 4, and Figures 5 and 6, respectively. Figure 3 Example of a metal traveller on an HZ-

23、ring Figure 4 Example of a plastic traveller on an HZ-ring Figure 5 Example of a metal traveller on a J-ring Figure 6 Example of a plastic traveller on a J-ring BS ISO 96-2:2009 ISO 96-2:2009(E) 4 ISO 2009 All rights reserved4.2 The values for traveller mass are given in Table 2. The traveller mass

24、is taken from the R20 series of preferred numbers in accordance with ISO 3. The range of traveller mass comprises values from 9 to 20 000 inclusive. The traveller mass represents the nominal mass, in grams, of 1 000 travellers of the same type. The tolerance on the nominal mass for 1 000 travellers

25、of the same type is 3 % for metal travellers and () 5 0 % +for plastic travellers. Table 2 Traveller mass Mass of traveller (grams per 1 000 travellers) 9 63 450 3 150 10 71 500 3 550 11,2 80 560 4 000 12,5 90 630 4 500 14 100 710 5 000 16 112 800 5 600 18 125 900 6 300 20 140 1 000 7 100 22,4 160 1

26、 120 8 000 25 180 1 250 9 000 28 200 1 400 10 000 31,5 224 1 600 11 200 35,5 250 1 800 12 500 40 280 2 000 14 000 45 315 2 240 16 000 50 355 2 500 18 000 56 400 2 800 20 000 BS ISO 96-2:2009 ISO 96-2:2009(E) ISO 2009 All rights reserved 5 5 Designation of travellers The designation of a traveller fo

27、r an HZ- or J-ring shall include the following information: a) “Traveller”; b) reference to this part of ISO 96 (i.e. ISO 96-2); c) the symbol “HZ” or “J”; d) the height, h, in millimetres, of the appropriate ring; e) the manufacturers designation for the traveller style (optional); f) the wire sect

28、ion symbol (if applicable), e.g. “f ”, “r ” (“f ” = flat, “r” = round); g) the traveller mass (see Table 2); h) the traveller material if it is other than steel (where this information is omitted, it is assumed that the traveller material is steel); i) the surface finish (optional); j) the presentat

29、ion (loose or stacked). BS ISO 96-2:2009 ISO 96-2:2009(E) ICS 59.120.10 Price based on 5 pages ISO 2009 All rights reserved BS ISO 96-2:2009 This page has been intentionally left blankBS ISO 96-2:2009 BSI Group Headquarters 389 Chiswick High Road, London, W4 4AL, UK Tel +44 (0)20 8996 9001 Fax +44 (

30、0)20 8996 7001 standards BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated

31、by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Sta

32、ndard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receiv

33、e the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the

34、Website http:/ In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and internat

35、ional standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing membe

36、rs of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to

37、British Standards via British Standards Online can be found at http:/ Further information about BSI is available on the BSI website at http:/ Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodie

38、s. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free u

39、se, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright and Licensing Manager. Tel: +44 (0)20 8996 7070 Email: