BS ISO 7790-2013 en_7862 Hydraulic fluid power Four-port modular stack valves and four-port directional control valves sizes 02 03 05 07 08 and 10 Clamping dimensions《液压传动.四油口叠加阀和四油口方向控制.pdf

《BS ISO 7790-2013 en_7862 Hydraulic fluid power Four-port modular stack valves and four-port directional control valves sizes 02 03 05 07 08 and 10 Clamping dimensions《液压传动.四油口叠加阀和四油口方向控制.pdf》由会员分享，可在线阅读，更多相关《BS ISO 7790-2013 en_7862 Hydraulic fluid power Four-port modular stack valves and four-port directional control valves sizes 02 03 05 07 08 and 10 Clamping dimensions《液压传动.四油口叠加阀和四油口方向控制.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwide NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Standards Publication BS ISO 7790:2013 Hydraulic fluid power Four-port modular stack valves and four-port directional control valves, sizes 02, 03, 05, 07, 08 and 10 Clamping dimensionsBS ISO 7790:

2、2013 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 7790:2013. It supersedes BS ISO 7790:1997, which is withdrawn. The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e M C E / 1 8 / - / 5 , C o n t r o l c o m p o n e

3、n t s . A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013. Published by

4、BSI Standards Limited 2013. ISBN 978 0 580 73621 6 ICS 23.100.50 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2013. Amendments issued since publicat

5、ion Date T e x t a f f e c t e dBS ISO 7790:2013 ISO 2013 Hydraulic fluid power Four-port modular stack valves and four-port directional control valves, sizes 02, 03, 05, 07, 08 and 10 Clamping dimensions Transmissions hydrauliques Appareils empilables et distributeurs quatre orifices, de tailles 02

6、, 03, 05, 07, 08 et 10 Dimensions de montage INTERNATIONAL STANDARD ISO 7790 Third edition 2013-03-01 Reference number ISO 7790:2013(E)BS ISO 7790:2013ISO 7790:2013(E)ii ISO 2013 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2013 All rights reserved. Unless otherwise specified, no part of thi

7、s publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in th

8、e country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 7790:2013ISO 7790:2013(E) ISO 2013 All rights reserved iii Contents Page Foreword iv Introduction v 1

9、 Scope . 1 2 Normative references 1 3 Terms and definitions . 1 4 Symbols 1 5 Tolerances . 1 6 Dimensions . 1 7 Working pressure 3 8 Identification statement (Reference to this International Standard) .3 Bibliography 4BS ISO 7790:2013ISO 7790:2013(E) Foreword ISO (the International Organization for

10、Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the r

11、ight to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Internation

12、al Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as

13、 an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. IS

14、O 7790 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 5, Control products and components. This third edition cancels and replaces the second edition (ISO 7790:1997), which has been technically revised.iv ISO 2013 All rights reservedBS ISO 7790:2013ISO 7790:2013(

15、E) Introduction In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. Typical components found in such systems are hydraulic valves and hydraulic modular stack valves. These devices control flow direction, pressure, or flow

16、rate of liquids in the enclosed circuit. ISO 2013 All rights reserved vBS ISO 7790:2013BS ISO 7790:2013Hydraulic fluid power Four-port modular stack valves and four-port directional control valves, sizes 02, 03, 05, 07, 08 and 10 Clamping dimensions 1 Scope This International Standard specifies clam

17、ping dimensions of four-port modular stack valves and four- port directional control valves, sizes 02, 03, 05, 07, 08, and 10, on mounting surfaces. The dimensions and sizes conform to ISO 4401 so as to ensure interchangeability of these valves and to reduce the number of fixing devices to be used.

18、It applies to clamping dimensions of four-port modular stack valves and four-port directional control valves which represent current practice. They are generally applicable to industrial equipment. 2 Normative references The following documents, in whole or in part, are normatively referenced in thi

19、s document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 4401, Hydraulic fluid power Four-port directional control valves Mounting surfaces

20、 ISO 5598, Fluid power systems and components Vocabulary ISO 5783, Hydraulic f luid power Code for identification of valve mounting surfaces and cartridge valve cavities 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 5598 apply. 4 Symbols For the pu

21、rposes of this International Standard, the following letter symbols apply: a) H 1identifies clamping length for the fixing devices on directional control valves; b) H 2identifies overall heights of modular stack valves. 5 Tolerances For tolerances and other data relating to the side of a modular sta

22、ck valve on which another modular stack valve or a directional control valve is mounted, see ISO 4401. 6 Dimensions Clamping dimensions for modular stack valves and directional control valves, sizes 02, 03, 05, 07, 08, and 10, in accordance with ISO 5783, with four service ports, are shown in Figure

23、 1 and given in Tables 1 and 2. Table 1 lists the preferred dimensions and should be used for new valve designs. Table 2 lists INTERNATIONAL ST ANDARD ISO 7790:2013(E) ISO 2013 All rights reserved 1BS ISO 7790:2013ISO 7790:2013(E) alternative non-preferred dimensions that are in current use but whic

24、h should not be used for new valve designs. The mounting surface shall be in accordance with ISO 4401. a) Directional control valve b) Modular stack valve a Dimension H 1is understood to be the mounting height (clamping length for fixing bolts) where fixing bolts with heads are used. Where studs are

25、 used, consult sales literature on valve heights before determining the length of these studs. b Dimension H 2is understood to be the overall mounting height of a modular stack valve, including O-ring plate height, if necessary. Figure 1 Clamping dimensions for four-port directional control valves a

26、nd modular stack valves, sizes 02, 03, 05, 07, 08, and 10 (mounting surface in accordance with ISO 4401) Table 1 Preferred clamping dimensions for four-port directional control valves and modular stack valves, sizes 02, 03, 05, 07, 08, and 10 (mounting surface in accordance with ISO 4401) Dimensions

27、 in millimetres Valve type Dimension Size 02 Size 03 Size 05 Size 07 Size 08 Size 10 Directional control valve H 1 Modular stack valve H 2 a NOTE The supplier shall establish the maximum working pressure for valves, subplates, and the manifold blocks. aWhen dimension H 2is not acceptable for design

28、reasons, it shall be increased or decreased in increments of 10 mm. Table 2 Alternative non-preferred clamping dimensions for four-port directional control valves and modular stack valves, sizes 02, 03, 05, 07, 08, and 10 (mounting surface in accordance with ISO 4401) Dimensions in millimetres Valve

29、 type Dimension Size 02 Size 03 Size 05 Size 07 Size 08 Size 10 Directional control valve H 1 None Modular stack valve H 2 None None None NoneNOTE The supplier shall establish the maximum working pressure for valves, subplates, and the manifold blocks.2 ISO 2013 All rights reservedBS ISO 7790:2013IS

30、O 7790:2013(E) 7 Working pressure For an indication of the maximum limit of the working pressure, see Note in Table 1. 8 Identification statement (Reference to this International Standard) Use the following statement in test reports, catalogues, and sales literature when electing to comply with this

31、 International Standard: “Modular stack valves and directional control valves clamping dimensions conform to ISO 7790, Hydraulic fluid power Four-port modular stack valves and four-port directional control valves, sizes 02, 03, 05, 07, 08 and 10 Clamping dimensions.” ISO 2013 All rights reserved 3BS

32、 ISO 7790:2013ISO 7790:2013(E) Bibliography 1 ISO 129-1, Technical drawings Indication of dimensions and tolerances Part 1: General principles 2 ISO 286-1, Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits 3 ISO 9

33、65-1, ISO general-purpose metric screw threads Tolerances Part 1: Principles and basic data 4 ISO 1101, Geometrical product specifications (GPS) Geometrical tolerancing Tolerances of form, orientation, location and run-out 5 ISO 1302, Geometrical Product Specifications (GPS) Indication of surface te

34、xture in technical product documentation4 ISO 2013 All rights reservedBS ISO 7790:2013BS ISO 7790:2013ISO 7790:2013(E) ISO 2013 All rights reserved ICS 23.100.50 Price based on 4 pagesThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards an

35、d other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited. British Standards Instit

36、ution (BSI) raising standards worldwide BSI 389 Chiswick High Road London W4 4AL UK Te l + 4 4 ( 0 ) 2 0 8 9 9 6 9 0 0 1 Fax +44 (0)20 8996 7001 Revisions British Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they pos

37、sess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity o

38、f which can be found on the inside front cover. S i m i l a r y f o r P A S s , p l e a s e n o t i f y B S I C u s t o m e r S e r v i c e s . Te l : + 4 4 ( 0 ) 2 0 8 9 9 6 9 0 0 1 F a x : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 1 BSI offers BSI Subscribing Members an individual updating service called PLUS

39、 which ensures that subscribers automatically receive the latest editions of British Standards and PASs. Te l : + 4 4 ( 0 ) 2 0 8 9 9 6 7 6 6 9 F a x : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 1 Email: Buying standards Yo u m a y b u y P D F a n d h a rd c o p y v e r s i o n s o f s t a n d a rd s d i re c t

40、 l y u s i n g a credit card from the BSI Shop on the website In addition all orders for BSI, international and foreign standards publications can be addressed to BSI Customer Services. Te l : + 4 4 ( 0 ) 2 0 8 9 9 6 9 0 0 1 F a x : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 1 Email: In response to orders for

41、international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Knowledge Centre. Te l : +

42、4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 4 F a x : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 5 Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Te l

43、: + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 2 F a x : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 0 1 Email: Information regarding online access to British Standards and PASs via British Standards Online can be found at Further information about British Standards is available on the BSI website at www.bsi- Copyright All the

44、data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BS

45、I for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI

46、. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department. Te l : + 4 4 ( 0 ) 2 0 8 9 9 6 7 0 7 0 Email: