BS ISO 6432-2015 en_3486 Pneumatic fluid power Single rod cylinders 1 000 kPa (10 bar) series bores from 8 mm to 25 mm Basic and mounting dimensions《气动流体动力.单杆汽缸.1100kPa(10bar)系列..pdf

《BS ISO 6432-2015 en_3486 Pneumatic fluid power Single rod cylinders 1 000 kPa (10 bar) series bores from 8 mm to 25 mm Basic and mounting dimensions《气动流体动力.单杆汽缸.1100kPa(10bar)系列..pdf》由会员分享，可在线阅读，更多相关《BS ISO 6432-2015 en_3486 Pneumatic fluid power Single rod cylinders 1 000 kPa (10 bar) series bores from 8 mm to 25 mm Basic and mounting dimensions《气动流体动力.单杆汽缸.1100kPa(10bar)系列..pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication BS ISO 6432:2015 Pneumatic fluid power Single rod cylinders, 1 000 kPa (10 bar) series, bores from 8 mm to 25 mm Basic and mounting dimensionsBS ISO 6432:2015 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 6432:2015. It supersedes B

2、S ISO 6432:1985 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MCE/18/-/3, Cylinders. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary pr

3、ovisions of a contract. Users are responsible for its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015 ISBN 978 0 580 84500 0 ICS 23.100.20 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was

4、published under the authority of the Standards Policy and Strategy Committee on 31 August 2015. Amendments/corrigenda issued since publication Date Text affectedBS ISO 6432:2015 ISO 2015 Pneumatic fluid power Single rod cylinders, 1 000 kPa (10 bar) series, bores from 8 mm to 25 mm Basic and mountin

5、g dimensions Transmissions pneumatiques Vrins simple tige, srie 1 000 kPa (10 bar), alsages de 8 mm 25 mm Dimensions de base et de montage INTERNATIONAL STANDARD ISO 6432 Second edition 2015-08-15 Reference number ISO 6432:2015(E)BS ISO 6432:2015ISO 6432:2015(E)ii ISO 2015 All rights reserved COPYRI

6、GHT PROTECTED DOCUMENT ISO 2015, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, wit

7、hout prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.is

8、o.orgBS ISO 6432:2015ISO 6432:2015(E)Foreword iv Introduction v 1 Scope . 1 2 Normative references 1 3 Terms and definitions . 1 4 Dimensions . 1 4.1 Basic dimensions . 1 4.2 Mounting dimensions . 1 5 Nominal stroke . 2 6 Bore sizes . 2 7 Mounting types . 2 8 Piston rod characteristics . 2 9 Identif

9、ication statement (reference to this International Standard) 2 Bibliography 6 ISO 2015 All rights reserved iii Contents PageBS ISO 6432:2015ISO 6432:2015(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). T

10、he work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-go

11、vernmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described

12、 in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to th

13、e possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO

14、list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as

15、well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 131, Fluid power systems, Subcommittee SC 3, Cylinders. This second edition cancel

16、s and replaces the first edition (ISO 6432:1985), which has been technically revised.iv ISO 2015 All rights reservedBS ISO 6432:2015ISO 6432:2015(E) Introduction In pneumatic fluid power systems, power is transmitted and controlled through a gas under pressure within a circuit. One component of such

17、 systems is the pneumatic cylinder. This is a device which converts power into linear mechanical force and motion. It consists of a movable element, i.e. a piston, and a piston rod, operating within a cylindrical bore. To enable them to be fastened to user mechanisms, pneumatic cylinders comprise, i

18、n addition, some devices called “mountings”. ISO 2015 All rights reserved vBS ISO 6432:2015BS ISO 6432:2015Pneumatic fluid power Single rod cylinders, 1 000 kPa (10 bar) series, bores from 8 mm to 25 mm Basic and mounting dimensions 1 Scope This International Standard establishes a metric series of

19、mounting dimensions required for interchangeability of commonly used pneumatic cylinders for a maximum working pressure of 1 000 kPa (10 bar). NOTE This International Standard allows manufacturers freedom of design in metric cylinders and does not restrict technical development but provides basic gu

20、idelines. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including

21、 any amendments) applies. ISO 3320, Fluid power systems and components Cylinder bores and piston rod diameters and area ratios Metric series ISO 4393, Fluid power systems and components Cylinders Basic series of piston strokes ISO 4395, Fluid power systems and components Cylinder piston rod end type

22、s and dimensions ISO 5598, Fluid power systems and components Vocabulary ISO 6099, Fluid power systems and components Cylinders Identification code for mounting dimensions and mounting types ISO 16030, Pneumatic fluid power Connections Ports and stud ends 3 Terms and definitions For the purposes of

23、this document, the terms and definitions given in ISO 5598 apply. 4 Dimensions 4.1 Basic dimensions The basic dimensions are given in Table 1 and shown in Figure 1. 4.2 Mounting dimensions The mounting dimensions are given in Tables 2 to 5 and shown in Figures 2 to 5. NOTE 1 The sign + after letters

24、 means that the stroke is to be added to the actual dimension. The tolerances of dimensions dependent on stroke included in the tables apply for strokes up to and including 100 mm. If strokes are longer than 100 mm, tolerances should be selected from national standards or by agreement between the ma

25、nufacturer and user. INTERNATIONAL ST ANDARD ISO 6432:2015(E) ISO 2015 All rights reserved 1BS ISO 6432:2015ISO 6432:2015(E) 5 Nominal stroke 5.1 Select the nominal strokes from the recommended values shown in ISO 4393. 5.2 The nominal stroke tolerance is , mm for strokes up to and including 100 mm.

26、 If strokes are longer than 100 mm, tolerances should be selected from national standards or by agreement between the manufacturer and user. 6 Bore sizes Included in this series are the following bore sizes AL, in millimetres, in accordance with ISO 3320: 8 10 12 16 20 25 7 Mounting types This Inter

27、national Standard includes a combination of the following mounting types as described in ISO 6099: MR3: Head threaded mounting (see Table 4, Figure 4); MP3: Cap fixed eye mounting (see Table 3, Figure 3); MS3: Head angle mounting (see Table 5, Figure 5); MF8: Head rectangular flange (two hole) mount

28、ing (see Table 2, Figure 2). 8 Piston rod characteristics This International Standard applies to the following piston rod characteristics: Shouldered or unshouldered male threads. The dimensions of the piston rod threads shall be chosen in accordance with ISO 4395. 9 Identification statement (refere

29、nce to this International Standard) Use the following statement in test reports, catalogues and sales literature when electing to comply with this International Standard: “Basic, mounting and accessories dimensions of pneumatic cylinders conform to ISO 6432, Pneumatic fluid power Single rod cylinder

30、s, 1 000 kPa (10 bar) series, bores from 8 mm to 25 mm Basic and mounting dimensions.”2 ISO 2015 All rights reservedBS ISO 6432:2015ISO 6432:2015(E) Key 1 TRP , theoretical reference point according to ISO 6099 Figure 1 Basic dimensions Table 1 Basic dimensions Dimensions in millimetres AL A KK EE a

31、 E D nom. tol. max. max. 8 10 12 16 20 25 12 12 16 16 20 22 0 2 M4 M4 M6 M6 M8 M10 1,25 M5 M5 M5 M5 G1/8 G1/8 18 20 24 24 34 34 20 22 26 27 40 40 aEE conforms to ISO 16030. Figure 2 Head rectangular flange (two hole) mounting (MF8) ISO 2015 All rights reserved 3BS ISO 6432:2015ISO 6432:2015(E) Table

32、 2 Dimensions for head rectangular flange (two hole) mounting (MF8) Dimensions in millimetres AL W a FB TF UF UR 1,4 H13 Js14 max. max. 8 10 12 16 20 25 13 13 18 18 19 23 4,5 4,5 5,5 5,5 6,6 6,6 30 30 40 40 50 50 45 53 55 55 70 70 25 30 30 30 40 40 aSee notes in 4.2. Figure 3 Cap fixed eye mounting

33、(MP3) Table 3 Dimensions for cap fixed eye mounting (MP3) Dimensions in millimetres AL EW XC a L CD MR d13 1 min. H9 max. 8 10 12 16 20 25 8 8 12 12 16 16 64 64 75 82 95 104 6 6 9 9 12 12 4 4 6 6 8 8 18 18 22 22 25 25 aSee notes in 4.2. Figure 4 Head threaded mounting (MR3)4 ISO 2015 All rights rese

34、rvedBS ISO 6432:2015ISO 6432:2015(E) Table 4 Dimensions for head threaded mounting (MP3) Dimensions in millimetres AL BE KW KV WF max. max. 1,2 8 10 12 16 20 25 M12 x 1,25 M12 x 1,25 M16 x 1,5 M16 x 1,5 M22 x 1,5 M22 x 1,5 7 7 8 8 11 11 19 19 24 24 32 32 16 16 22 22 24 28 Figure 5 Head angle mountin

35、g (MS3) Table 5 Dimensions for head angle mounting (MS3) Dimensions in millimetres AL XS AO AU LH TR US AB 1,4 max. max. 0,3 Js14 max. H13 8 10 12 16 20 25 24 24 32 32 36 40 14 14 16 16 20 20 6 6 7 7 8 8 16 16 20 20 25 25 25 25 32 32 40 40 35 42 47 47 55 55 4,5 4,5 5,5 5,5 6,6 6,6 ISO 2015 All right

36、s reserved 5BS ISO 6432:2015ISO 6432:2015(E) Bibliography 1 ISO 6430, Pneumatic fluid power Single rod cylinders, 1 000 kPa (10 bar) series, with integral mountings, bores from 32 mm to 250 mm Mounting dimensions 2 ISO 15524, Pneumatic fluid power Cylinders Single-rod short-stroke cylinders, 1 000 k

37、Pa (10 bar) series, bores from 20 mm to 100 mm 3 ISO 15552, Pneumatic fluid power Cylinders with detachable mountings, 1 000 kPa (10 bar) series, bores from 32 mm to 320 mm Basic, mounting and accessories dimensions 4 ISO 21287, Pneumatic fluid power Cylinders Compact cylinders, 1000 kPa (10 bar) se

38、ries, bores from 20 mm to 100 mm6 ISO 2015 All rights reservedBS ISO 6432:2015BS ISO 6432:2015ISO 6432:2015(E) ISO 2015 All rights reserved ICS 23.100.20 Price based on 6 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-re

39、lated publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We bring togeth

40、er business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organiz

41、ations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services

42、team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standa

43、rds Development Organizations, hard copies can be ordered from our Customer Services team. Subscriptions Our range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL) youll have

44、 instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards,

45、both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribin

46、g Member and the benefits of membership, please visit With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation

47、is current. For further information, email . Revisions Our British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or othe

48、r BSI publication please inform the Knowledge Centre. Copyright All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the internati

49、onal standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying