BS ISO 814-2017 en_9506 Rubber vulcanized or thermoplastic Determination of adhesion to metal Two-plate method《硫化橡胶或热塑性橡胶.金属附着力的测定.双板法》.pdf

《BS ISO 814-2017 en_9506 Rubber vulcanized or thermoplastic Determination of adhesion to metal Two-plate method《硫化橡胶或热塑性橡胶.金属附着力的测定.双板法》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 814-2017 en_9506 Rubber vulcanized or thermoplastic Determination of adhesion to metal Two-plate method《硫化橡胶或热塑性橡胶.金属附着力的测定.双板法》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、Rubber, vulcanized or thermoplastic Determination of adhesion to metal Two-plate method BS ISO 814:2017 BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06 ISO 2017 Rubber, vulcanized or thermoplastic Determination of adhesion to metal Two-plate method Caoutchouc vulca

2、nis ou thermoplastique Dtermination de ladhrence au mtal Mthode deux plaques INTERNATIONAL STANDARD ISO 814 Sixth edition 2017-07 Reference number ISO 814:2017(E) National foreword This British Standard is the UK implementation of ISO 814:2017. It supersedes BS ISO 814:2011, which is withdrawn. The

3、UK participation in its preparation was entrusted to Technical Committee PRI/22, Testing and analysis of rubber. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract.

4、 Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017 ISBN 978 0 580 97185 3 ICS 83.060 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authori

5、ty of the Standards Policy and Strategy Committee on 31 August 2017. Amendments/corrigenda issued since publication Date Text affected BRITISH STANDARD BS ISO 814:2017 ISO 2017 Rubber, vulcanized or thermoplastic Determination of adhesion to metal Two-plate method Caoutchouc vulcanis ou thermoplasti

6、que Dtermination de ladhrence au mtal Mthode deux plaques INTERNATIONAL STANDARD ISO 814 Sixth edition 2017-07 Reference number ISO 814:2017(E) BS ISO 814:2017 ISO 814:2017(E)ii ISO 2017 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in Switzerland All rights reserved. Unless o

7、therwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the addre

8、ss below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.org BS ISO 814:2017 ISO 814:2017(E)ii ISO 2017 All rights reserved COPYRIGHT PROTECTE

9、D DOCUMENT ISO 2017, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior w

10、ritten permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.orgISO 814

11、:2017(E)Foreword iv 1 Scope . 1 2 Normative references 1 3 T erms and definitions . 1 4 Principle 1 5 Apparatus . 2 6 Calibration 4 7 Test piece 4 7.1 Dimensions . 4 7.2 Preparation 4 7.3 Number 5 7.4 Conditioning 5 8 Procedure. 5 9 Expression of results 5 9.1 Adhesion value 5 9.2 Adhesion failure s

12、ymbols . 5 10 Test report . 6 Annex A (normative) Calibration schedule . 7 ISO 2017 All rights reserved iii Contents Page BS ISO 814:2017 ISO 814:2017(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The

13、work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-gover

14、nmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in

15、 the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives). Attention is drawn to th

16、e possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO

17、list of patent declarations received (see www .iso .org/ patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions

18、 related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html. This document was prepared by Technical Committee ISO/TC 45, Rubber and

19、rubber products, Subcommittee SC 2, Testing and analysis. This sixth edition cancels and replaces the fifth edition (ISO 814:2011), of which it constitutes a minor revision to update the normative references in Clause 2 as well as the failure symbols in 9.2.iv ISO 2017 All rights reserved BS ISO 814

20、:2017 ISO 814:2017(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a

21、 subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commissio

22、n (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents shoul

23、d be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for

24、identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents). Any trade name used in this document is information given for the

25、 convenience of users and does not constitute an endorsement. For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in t

26、he Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html. This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. This sixth edition cancels and replaces the fifth edition (ISO 814:2011),

27、of which it constitutes a minor revision to update the normative references in Clause 2 as well as the failure symbols in 9.2.iv ISO 2017 All rights reserved INTERNATIONAL ST ANDARD ISO 814:2017(E) Rubber, vulcanized or thermoplastic Determination of adhesion to metal Two-plate method WARNING 1 Pers

28、ons using this document should be familiar with normal laboratory practice. This document does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with a

29、ny national regulatory conditions. WA R N I N G 2 C er t a i n p ro c ed ure s s p e c i f ie d in t his do c u ment m i g ht i nvol ve t he u se or g en er a t i o n of substances, or the generation of waste, that could constitute a local environmental hazard. Reference should be made to appropriat

30、e documentation on safe handling and disposal after use. 1 Scope This document specifies a method for determining the adhesion strength of rubber-to-metal bonds where the rubber part is assembled between two parallel metal plates, using the adhesive system under investigation. The method is applicab

31、le primarily to test pieces, prepared in the laboratory under standard conditions, such as can be used to provide data for the development of rubber compounds and control of methods of manufacture. 2 Normative references The following documents are referred to in the text in such a way that some or

32、all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 5893, Rubber and plastics test equipment Tensile, flexural and compressi

33、on types (constant rate of traverse) Specification ISO 18899:2013, Rubber Guide to the calibration of test equipment ISO 23529, Rubber General procedures for preparing and conditioning test pieces for physical test methods 3 T erms an d definiti ons No terms and definitions are listed in this docume

34、nt. ISO and IEC maintain terminological databases for use in standardization at the following addresses: ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp IEC Electropedia: available at h t t p :/ www .electropedia .org/ 4 Principle The test consists in measuring the force req

35、uired to cause the rupture of a unit of standard dimensions, comprising rubber bonded to two parallel metal plates, the direction of the force being at 90 to the bonded surface. ISO 2017 All rights reserved 1 BS ISO 814:2017 ISO 814:2017(E) 5 Apparatus 5.1 Tensile-testing machine, complying with the

36、 requirements of ISO 5893, capable of measuring force with an accuracy corresponding to class 2 as defined in ISO 5893, and with a rate of traverse of the moving grip of 25 mm/min 5 mm/min. NOTE Inertia (pendulum) type dynamometers are apt to give results which differ because of frictional and inert

37、ial effects. An inertialess (for example, electronic or optical transducer) type dynamometer gives results which are free from these effects and is therefore preferred. 5.2 Fixtures, for holding the test pieces in the test machine (5.1), which permit accurate centring of the applied load during the

38、test. A suitable type of fixture is shown in Figure 1. Dimensions in millimetres a) Assembly of parts2 ISO 2017 All rights reserved BS ISO 814:2017 ISO 814:2017(E) 5 Apparatus 5.1 Tensile-testing machine, complying with the requirements of ISO 5893, capable of measuring force with an accuracy corres

39、ponding to class 2 as defined in ISO 5893, and with a rate of traverse of the moving grip of 25 mm/min 5 mm/min. NOTE Inertia (pendulum) type dynamometers are apt to give results which differ because of frictional and inertial effects. An inertialess (for example, electronic or optical transducer) t

40、ype dynamometer gives results which are free from these effects and is therefore preferred. 5.2 Fixtures, for holding the test pieces in the test machine (5.1), which permit accurate centring of the applied load during the test. A suitable type of fixture is shown in Figure 1. Dimensions in millimet

41、res a) Assembly of parts2 ISO 2017 All rights reserved ISO 814:2017(E) b) Part A c) Part B d) Part C Key A tail fillet to suit test machine B bridle fillet threaded to take part C C split across centre to accept test piece and threaded to fit into part B D metal part of test piece E rubber Fig u r e

42、 1 E x a mple of t es t f i x t ure f or hold i n g r ubb er -t o - me t a l b ond t es t pie c e s ISO 2017 All rights reserved 3 BS ISO 814:2017 ISO 814:2017(E) 6 Calibration The test apparatus shall be calibrated in accordance with Annex A. 7 Test piece 7.1 Dimensions The standard test piece shal

43、l consist of a rubber cylinder 3 mm 0,1 mm thick and of diameter between 35 mm and 40 mm known to the nearest 0,1 mm, having its circular ends bonded to the faces of two metal plates of equal diameter, the determination of dimensions of the test piece being in accordance with ISO 23529. The diameter

44、 of the metal plates shall be approximately 0,1 mm less than that of the rubber cylinder. The thickness of the metal plates shall be not less than 9 mm. A typical test piece is shown in Figure 2. Dimensions in millimetres Key 1 test piece Figure 2 Example of standard test piece 7.2 Preparation 7.2.1

45、 Circular metal plates of the standard dimensions shall be prepared preferably from rolled carbon steel bar. Other metals may be used provided that the parts are in conformity with the essential dimensions. The smooth metal parts shall be prepared and treated in accordance with the adhesion system u

46、nder investigation. 7.2.2 Rubber discs shall be cut using a circular die of such size that a limited amount of flash is obtained on moulding. The surface of the rubber to be bonded to the metal shall be treated in accordance with the method being investigated. 7.2.3 The rubber discs and metal end pi

47、eces shall then be assembled for moulding in the mould. The mould shall be constructed so that the rubber projects beyond the edges of the metal end pieces by approximately 0,05 mm in order to prevent tearing of the rubber by the edge of the metal during testing. 7.2.4 During the preparation of the

48、test piece, great care shall be taken to keep the exposed surfaces of the rubber and metal free from dust, moisture and other foreign matter. The surfaces shall not be touched by hand during assembly.4 ISO 2017 All rights reserved BS ISO 814:2017 ISO 814:2017(E) 6 Calibration The test apparatus shal

49、l be calibrated in accordance with Annex A. 7 Test piece 7.1 Dimensions The standard test piece shall consist of a rubber cylinder 3 mm 0,1 mm thick and of diameter between 35 mm and 40 mm known to the nearest 0,1 mm, having its circular ends bonded to the faces of two metal plates of equal diameter, the determination of dimensions of the test piece being in accordance with ISO 23529. The diameter of the metal plates shall be approximately 0,1 mm less than that of the