BS ISO 7388-3-2016 en_3998 Tool shanks with 7 24 taper for automatic tool changers Retention knobs of forms AD AF UD UF JD and JF《自动工具转换用7 24锥度工具柄.AD、AF、UD、UF、JD和JF型保持按钮》.pdf

《BS ISO 7388-3-2016 en_3998 Tool shanks with 7 24 taper for automatic tool changers Retention knobs of forms AD AF UD UF JD and JF《自动工具转换用7 24锥度工具柄.AD、AF、UD、UF、JD和JF型保持按钮》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 7388-3-2016 en_3998 Tool shanks with 7 24 taper for automatic tool changers Retention knobs of forms AD AF UD UF JD and JF《自动工具转换用7 24锥度工具柄.AD、AF、UD、UF、JD和JF型保持按钮》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication BS ISO 7388-3:2016 Tool shanks with 7/24 taper for automatic tool changers Part 3: Retention knobs of forms AD, AF, UD, UF, JD and JFBS ISO 7388-3:2016 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 7388-3:2016. It supersedes BS ISO

2、 7388-3:2013 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport

3、to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016 ISBN 978 0 580 90277 2 ICS 25.060.20 Compliance with a British Standard cannot confer immunity from legal obligati

4、ons. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 February 2016. Amendments/corrigenda issued since publication Date T e x t a f f e c t e dBS ISO 7388-3:2016 ISO 2016 Tool shanks with 7/24 taper for automatic tool changers Part 3: Rete

5、ntion knobs of forms AD, AF, UD, UF, JD and JF Queues doutils conicit 7/24 pour changement automatique doutils Partie 3: Tirettes de formes AD, AF, UD, UF, JD et JF INTERNATIONAL STANDARD ISO 7388-3 Third edition 2016-02-01 Reference number ISO 7388-3:2016(E)BS ISO 7388-3:2016ISO 7388-3:2016(E)ii IS

6、O 2016 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on

7、 the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22

8、749 09 47 copyrightiso.org www.iso.orgBS ISO 7388-3:2016ISO 7388-3:2016(E)Foreword iv Introduction v 1 Scope . 1 2 Normative references 1 3 Dimensions . 1 3.1 General . 1 3.2 Retention knobs of form AD, for centric inner cooling lubricant supply 1 3.3 Retention knobs of form AF, without cooling lubr

9、icant supply 2 3.4 Retention knobs of form UD, for centric inner cooling lubricant supply 3 3.5 Retention knobs of form UF, without cooling lubricant supply 4 3.6 Retention knobs of form JD with centric inner cooling lubricant supply . 5 3.7 Retention knobs of form JF, without cooling lubricant supp

10、ly 6 3.8 Retention knobs with data medium . 7 4 Material 7 5 O-ring 8 6 Designation 8 Bibliography 9 ISO 2016 All rights reserved iii Contents PageBS ISO 7388-3:2016ISO 7388-3:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bo

11、dies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizatio

12、ns, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its furthe

13、r maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives

14、). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Intr

15、oduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to

16、 conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 2, Holding tools, adap

17、tive items and interfaces. This third edition cancels and replaces the second edition (ISO 7388-3:2013), of which it constitutes a minor revision with the following changes: in the title and in all the text, “retention knobs for shanks of form” was changed to “retention knobs of form”; forms AC and

18、UC have been deleted from the title and from the designation (Clause 6); a footnote was added to Tables 1 and 5. ISO 7388 consists of the following parts, under the general title Tool shanks with 7 /24 taper for automatic tool changers: Part 1: Dimensions and designation of shanks of forms A, AD, AF

19、, U, UD and UF Part 2: Dimensions and designation of shanks of forms J, JD, and JF Part 3: Retention knobs of forms AD, AF, UD, UF, JD and JFiv ISO 2016 All rights reservedBS ISO 7388-3:2016ISO 7388-3:2016(E) Introduction The aim of ISO 7388 is to integrate existing standards which are most commonly

20、 used as an industrial standard. In addition, the different developments for cooling and data chip have been taken into account. ISO 2016 All rights reserved vBS ISO 7388-3:2016BS ISO 7388-3:2016Tool shanks with 7/24 taper for automatic tool changers Part 3: Retention knobs of forms AD, AF, UD, UF,

21、JD and JF 1 Scope This part of ISO 7388 specifies the dimensions of retention knobs of forms AD, AF, UD, UF, JD and JF for tool shanks with a 7/24 taper for automatic tool changers used on machines having an automatic gripping system for feeding tools from the magazine to the spindle and vice-versa.

22、 These tools are designed with the most important dimensions for use in spindle noses according to ISO 9270 (all parts). 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, o

23、nly the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1629, Rubber and latices Nomenclature ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indicati

24、ons ISO 2768-2, General tolerances Part 2: Geometrical tolerances for features without individual tolerance indications ISO 8015, Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules 3 Dimensions 3.1 General All dimensions and tolerances are given in millimetres; tole

25、rancing is according to ISO 8015. Tolerances not specified shall be of tolerance class “m” in accordance with ISO 2768-1 and of class “k” in accordance with ISO 2768-2. 3.2 Retention knobs of form AD, for centric inner cooling lubricant supply The dimensions of retention knobs of form AD shall be in

26、 accordance with the dimensions shown in Figure 1 and given in Table 1. INTERNATIONAL ST ANDARD ISO 7388-3:2016(E) ISO 2016 All rights reserved 1BS ISO 7388-3:2016ISO 7388-3:2016(E) Key a Thread undercut, at the manufacturers discretion. b Chamfered end (CH), according to ISO 4753. Figure 1 Retentio

27、n knob Form AD Centric inner cooling lubricant supply Table 1 Retention knobs Form AD DimensionsDimension Shank no. d 1 d 2 d 3 d 4 d 5 d 7 l 1 l 2 l 3 l 4 l 5 l 6 l 12 sf7 f7 , , ,0,1 0,1 ,min. ,30 a 13 13 17 9 M12 44 24 19 20 4 5 10 14 40 19 17 23 14 7 M16 54 26 20 28 4 7 13 19 45 23 21 30 17 9,5

28、M20 65 30 23 35 5 8 16 24 50 28 25 36 21 11,5 M24 74 34 25 40 5 10 19 30 60 40 32 52 30 14 M30 90 40 30 50 6 12 24 46 aDimensions only for form AF. 3.3 Retention knobs of form AF, without cooling lubricant supply The dimensions of retention knobs of form AF shall be in accordance with the dimensions

29、 shown in Figure 2 and given in Table 2. Other dimensions are the same as form AD.2 ISO 2016 All rights reservedBS ISO 7388-3:2016ISO 7388-3:2016(E) Figure 2 Retention knob Form AF Without cooling lubricant supply Table 2 Retention knobs Form AF DimensionsDimension Shank no. d 1f7 d 6h11 l 7 , l 8 ,

30、 l 9 O-ring 30 13 11,5 2,3 1,4 11 1,0 40 19 14,6 3,0 1,9 27 14 1,5 45 23 17, 8 3,3 2,5 33 17 2,0 50 28 20,8 4,5 3,0 37 20 2,5 60 40 27, 8 5,5 3,0 45 27 2,5 3.4 Retention knobs of form UD, for centric inner cooling lubricant supply The dimensions of retention knobs of form UD shall be in accordance w

31、ith the dimensions shown in Figure 3 and given in Table 3. ISO 2016 All rights reserved 3BS ISO 7388-3:2016ISO 7388-3:2016(E) Key a Thread undercut, at the manufacturers discretion. b Chamfered end (CH), according to ISO 4753. Figure 3 Retention knob Form UD Centric inner cooling lubricant supply Ta

32、ble 3 Retention knobs Form UD DimensionsDimension Shank d 1 d 2 d 3 d 4 d 5 d 7 l 1 l 2 l 3 l 4 l 5 l 6 l 10 s no. ,h6 nom. tol. , , , , , , ,nom. tol. 30 13,35 13 16,5 ,9,3 4,15 M12 31,8 11,8 8,15 20 2,75 5 2,4 13 ,40 18,95 17 22,5 12,95 7, 35 M16 44,4 16,4 11,15 28 3,25 7 3,5 18 ,45 24,05 21 30 16

33、,3 9,25 M20 55,95 20,95 14,85 35 4,25 8 3,85 24 ,50 29,1 25 37 19,6 11,55 M24 65,55 25,55 17,95 40 5,25 10 4,85 30 ,60 37, 25 32 50 24,95 13,85 M30 88,15 38,15 27,65 50 7,75 12 6,75 36 ,3.5 Retention knobs of form UF, without cooling lubricant supply The dimensions of retention knobs of form UF shal

34、l be in accordance with the dimensions shown in Figure 4 and given in Table 4. Other dimensions are as for form UD.4 ISO 2016 All rights reservedBS ISO 7388-3:2016ISO 7388-3:2016(E) Figure 4 Retention knob Form UF Without cooling lubricant supply Table 4 Retention knob Form UF DimensionsDimension Sh

35、ank no. d 1 d 6 l 7 l 8 l 9 O-ring ,h11 ,30 13,35 11,5 2,3 1,4 11 1,0 40 18,95 14,6 3,0 1,9 27 14 1,5 45 24,05 17, 8 3,3 2,5 33 17 2,0 50 29,1 20,8 4,5 3,0 37 20 2,5 60 37, 25 27, 8 5,5 3,0 45 27 2,5 3.6 Retention knobs of form JD with centric inner cooling lubricant supply The dimensions of retenti

36、on knobs of form JD shall be in accordance with the dimensions shown in Figure 5 and given in Table 5. ISO 2016 All rights reserved 5BS ISO 7388-3:2016ISO 7388-3:2016(E) Key a Thread undercut, at the manufacturers discretion. b Chamfered end (CH), according to ISO 4753. c = 45 or = 60. This informat

37、ion should be given and taken over in the designation (see Clause 6). Figure 5 Retention knob Form JD Centric inner cooling lubricant supply Table 5 Retention knobs Form JD DimensionsDimension Shank no. d 1 d 2 d 3 d 4 d 5 d 7 l 1 l 2 l 3 l 4 l 5 l 6 l 10 l 11 l 12 r 1 s ,h7 , , ,6h , , , , ,30 a 11

38、 12,5 16,5 7 M12 43 23 18 20 5 4 2,5 3,5 10 2 13 40 a 15 17 23 10 M16 60 35 28 25 6 5 4 4 13 3 19 45 19 21 31 14 7 M20 70 40 31 30 8 6 5 6 16 4 24 50 23 25 38 17 8,5 M24 85 45 35 40 10 8 5 8 19 5 30 60 32 31 56 24 12 M30 115 65 53 50 14 10 7 11 24 5 46 aDimensions only for form JF. 3.7 Retention kno

39、bs of form JF, without cooling lubricant supply The dimensions of retention knobs of form JF shall be in accordance with the dimensions shown in Figure 6. Other dimensions are as for form JD.6 ISO 2016 All rights reservedBS ISO 7388-3:2016ISO 7388-3:2016(E) Figure 6 Retention knob Form JF Without co

40、oling lubricant supply 3.8 Retention knobs with data medium For forms AF and UF without a hole, it is possible to install a data medium hole. If a data medium hole is needed for form JF, the dimensions shall be defined by the manufacturer according to the data medium used. The location shall be as s

41、hown in Figure 7. See Figures 2 and 4 and Tables 2 and 4. The general dimensions are given in Table 6. Figure 7 Retention knob with data medium Table 6 Fitting dimension of the data medium b max 0,3 45 or R 0,3 a d 8 10 , t 4,6 , aAt the manufacturers discretion. 4 Material The steel is chosen at th

42、e manufacturers discretion but shall have a tensile strength of at least 980 N/mm 2and a hardness of from 55 HRC to 60 HRC. No area of the retention knob shall be through hardened. ISO 2016 All rights reserved 7BS ISO 7388-3:2016ISO 7388-3:2016(E) 5 O-ring The O-ring shall be according to ISO 1629 a

43、nd shall be included as part of the delivery. 6 Designation A retention knob in accordance with this part of ISO 7388 shall be designated as follows: a) “Retention knob”; b) a reference to this part of ISO 7388, i.e. ISO 7388-3; c) a dash; d) form AD, AF, UD, UF, JD or JF; e) taper size; f) a dash;

44、g) values, in degrees (45 or 60). NOTE f) and g) only apply for retention knobs forms JD and JF. EXAMPLE 1 Designation of a retention knob in accordance with ISO 7388-3, form AD, shank No. 40: Retention knob ISO 7388-3-AD40 EXAMPLE 2 Designation of a retention knob in accordance with ISO 7388-3, for

45、m JD, shank No. 40 with a angle of 45: Retention knob ISO 7388-3-JD40-458 ISO 2016 All rights reservedBS ISO 7388-3:2016ISO 7388-3:2016(E) Bibliography 1 ISO 4753, Fasteners Ends of parts with external ISO metric thread 2 ISO 9270-1, 7/24 taper spindle noses for automatic tool changers Part 1: Dimen

46、sions and designation of spindle noses of forms S and SF 3 ISO 9270-2, 7/24 taper spindle noses for automatic tool changers Part 2: Dimensions and designation of spindle noses of forms J and JF ISO 2016 All rights reserved 9BS ISO 7388-3:2016ISO 7388-3:2016(E) ISO 2016 All rights reserved IC S 25.06

47、0.20 Price based on 9 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardization products are publishe

48、d by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizat