BS ISO 603-9-1999 en_5291 Bonded abrasive products - Dimensions - Grinding wheels for high pressure grinding《粘合磨料产品.尺寸.高压磨削用砂轮》.pdf

《BS ISO 603-9-1999 en_5291 Bonded abrasive products - Dimensions - Grinding wheels for high pressure grinding《粘合磨料产品.尺寸.高压磨削用砂轮》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 603-9-1999 en_5291 Bonded abrasive products - Dimensions - Grinding wheels for high pressure grinding《粘合磨料产品.尺寸.高压磨削用砂轮》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS ISO 603-9:1999 ICS 25.

2、100.70 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Bonded abrasive products Dimensions Part 9: Grinding wheels for high pressure grindingThis British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the authority o

3、f the Standards Committee and comes into effect on 15 November 1999 BSI 11-1999 ISBN 0 580 35705 8 BS ISO 603-9:1999 Amendments issued since publication Amd. No. Date Comments National foreword This British Standard reproduces verbatim ISO 603-9:1999 and implements it as the UK national standard. Th

4、e UK participation in its preparation was entrusted to Technical Committee MTE/13, Grinding wheels, abrasive tools, paper, cloths and powder, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interp

5、retation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards whic

6、h implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does no

7、t purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside f

8、ront cover, the ISO title page, pages ii and iii, a blank page, pages 1 to 4, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.A Referencenumbe r ISO6039:1999 (E) INTERNATIONAL STANDARD ISO 6039 Firstedition 199907

9、15 Bondedabrasiveproducts Dimensions Part9: Grindingwheelsforhighpressuregrinding ProduitsabrasifsagglomrsDimensions Partie9:MeulespourmeulagehautepressionISO6039:1999(E) ii Foreword ISO (the InternationalOrganizationforStandardization)isaworldwidefederationofnationalstandardsbodies(ISO memberbodies

10、).TheworkofpreparingInternationalStandardsisnormallycarriedoutthroughISOtechnical committees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeenestablishedhas therighttoberepresentedonthatcommittee.Internationalorganizations,governmentalandnongovernmental,in liaisonwithISO,alsotakep

11、artinthework.ISOcollaboratescloselywiththeInternationalElectrotechnical Commission(IEC)onallmattersofelectrotechnicalstandardization. InternationalStandardsaredraftedinaccordancewiththerulesgivenintheISO/IECDirectives,Part3. DraftInternationalStandardsadoptedbythetechnicalcommitteesarecirculatedtoth

12、 ememberbodiesforvoting. PublicationasanInternationalStandardrequiresapprovalbyatleast75%ofthememberbodiescastingavote. InternationalStandardISO6039waspreparedbyTechnicalCommitteeISO/TC 29,Smalltools,subcommittee SC5, Grindingwheelsandabrasives . Thisfirstedition,togetherwithISO6031:1999toISO6038:19

13、9 9andISO60310:1999toISO60316:1999, cancelsandreplacesISO/R603:1967,ISO6032:1981,ISO1117:1975,ISO2220:1972,ISO2933:1974, ISO3290:1976andISO3921:1976asatechnicalrevisionofthesestandards. ISO603consistsofthefollowingparts,underthegeneraltitle BondedabrasiveproductsDimensions : Part1:Grindingwheelsfore

14、xternalcylindricalgrindingbetweencentres Part2:Grindingwheelsforcentrelessexternalcylindricalgrinding Part3:Grindingwheelsforinternalcylindricalgrinding Part4:Grindingwheelsforsurfacegrinding/peripheralgrinding Part5:Grindingwheelsforsurfacegrinding/facegrinding Part6:Grindingwheelsfortoolandtoolroo

15、mgrinding Part7:Grindingwheelsformanuallyguidedgrinding Part8:Grindingwheelsfordeburringandfettling/snagging Part9:Grindingwheelsforhighpressuregrinding Part10:Stonesforhoningandsuperfinishings Part11:Handfinishingsticks Part12:Grindingwheelsfordeburringandfettlingonastraightgrinder ISO6039:1999(E)

16、iii Part13:Grindingwheelsfordeburringandfettlingonaverticalgrinder Part14:Grindingwheelsfordeburringandfettling/snaggingonananglegrinder Part15:Grindingwheelsforcuttingoffonstationaryormobilecuttingoffmachines Part16:GrindingwheelsforcuttingoffonhandheldpowertoolsINTERNATIONALSTANDARD ISO6039:1999(E

17、) 1 BondedabrasiveproductsDimensions Part9: Grindingwheelsforhighpressuregrinding 1Scope ThispartofISO603specifiesthenominaldimensions,inmillimeters,of Type1:Straightgrindingwheel Thesebondedabrasiveproductsareintendedtobeusedforhighpressuregrinding.Theworkpieceandthe grindingwheelaremechanicallygui

18、ded. 2Normativereferences The following normativedocumentscontainprovisionswhich,throughreferenceinthistext,constituteprovisionsof this partofISO 603.Fordatedreferences,subsequentamendmentsto,orrevisionsof,anyofthesepublicationsdo notapply.However,partiestoagreementsbasedonthispartofISO 603areencour

19、agedtoinvestigatethe possibilityofapplyingthemostrecenteditionsofthenormativedocumentsindicatedbelow.For undated references,thelateseditionofthenormativedocumentreferre dtoapplies.MembersofISOandIECmaintain registersofcurrentlyvalidInternationalStandards. ISO525:1999, BondedabrasiveproductsGeneralre

20、quirements . ISO6103:1999, BondedabrasiveproductsStaticbalancingofgrindingwheelsTesting . ISO13942: 1) , BondedabrasiveproductsLimitdeviationsandrunouttolerances . 1) Tobepublished.ISO6039:1999(E) 2 3Dimensions SeeFigure1andTable1. Figure1Type1 Table1DimensionsofType1 DTH 40 50 63 80 100 125 152 406

21、 X X 152,4 508 X X X 152,4 203,2 610 X X X X 203,2 304,8 762 X X X 203,2 304,8 914 X X X 304,8 4Designation Acompletedesignationofabondedabrasiveproductinaccordancewit h this part of ISO 603 shall be consist of the followinginformation: a) b) designationofthebondedabrasives,e.g.Grindingwheel; refere

22、nceofthispartofISO603; c) d) e) f) type(shape); dimensions; specificationsofaninternalnature; themaximumoperatingspeed. InaccordancewithISO525 andthispartofISO603 EXAMPLE Agrindingwheelforhig hpressuregrinding,Type 1, D=610mm , T=80mm , H=203,2mm , nature of abrasiveA, grainsize 12,grade Z,structure

23、 2,natureofbond Bandamaximumoperatingspeedof8 0 m/sisdesignatedas follows: Grinding wheelISO60391610 380 3203,2 A12Z2B80m/s ISO6039:1999(E) 3 5Specifications Thespecificationsarelefttothemanufacturesdiscretion,seeISO525. 5.1Tolerances LimitdeviationsandrunouttolerancesinaccordancewithISO13942. 5.2Ba

24、lancing BalancingisinaccordancewithISO6103. 5.3Marking MarkingofbondedabrasiveproductsisinaccordancewithISO525.ISO6039:1999(E) 4 Bibliography 1ISO84861, BondedabrasivesDeterminationanddesignationofgrainsizedistributionPart1:MacrogritsF4 toF220 . 2ISO84862, BondedabrasivesDeterminationanddesignationo

25、fgrainsizedistributionPart2:Microgrits F230toF1200 .BS ISO 603-9:1999 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

26、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Rev

27、isions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or a

28、mbiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscri

29、bers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to

30、supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Vario

31、us BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the p

32、urchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodie

33、s. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free u

34、se, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.