BS ISO 6020-2-2015 en_1532 Hydraulic fluid power Mounting dimensions for single rod cylinders 16 MPa (160 bar) series Compact series《液压流体动力.16MPa(160bar)系列单杆汽缸用安装尺寸.小型系列》.pdf

《BS ISO 6020-2-2015 en_1532 Hydraulic fluid power Mounting dimensions for single rod cylinders 16 MPa (160 bar) series Compact series《液压流体动力.16MPa(160bar)系列单杆汽缸用安装尺寸.小型系列》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 6020-2-2015 en_1532 Hydraulic fluid power Mounting dimensions for single rod cylinders 16 MPa (160 bar) series Compact series《液压流体动力.16MPa(160bar)系列单杆汽缸用安装尺寸.小型系列》.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication BS ISO 6020-2:2015 Hydraulic fluid power Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Part 2: Compact seriesBS ISO 6020-2:2015 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 6020-2:2015. It supersedes BS ISO

2、 6020-2:2006 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MCE/18/-/3, Cylinders. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provi

3、sions of a contract. Users are responsible for its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015 ISBN 978 0 580 83205 5 ICS 23.100.20 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was pub

4、lished under the authority of the Standards Policy and Strategy Committee on 31 August 2015. Amendments/corrigenda issued since publication Date Text affectedBS ISO 6020-2:2015 ISO 2015 Hydraulic fluid power Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Part 2: Compact series

5、 Transmissions hydrauliques Dimensions dinterchangeabilit des vrins 16 MPa (160 bar) simple tige Partie 2: Srie compacte INTERNATIONAL STANDARD ISO 6020-2 Fourth edition 2015-08-15 Reference number ISO 6020-2:2015(E)BS ISO 6020-2:2015ISO 6020-2:2015(E)ii ISO 2015 All rights reserved COPYRIGHT PROTEC

6、TED DOCUMENT ISO 2015, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

7、 written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.orgBS IS

8、O 6020-2:2015ISO 6020-2:2015(E)Foreword iv Introduction v 1 Scope . 1 2 Normative references 1 3 Terms and definitions . 1 4 Dimensions . 1 5 Bore sizes . 2 6 Piston stroke tolerances . 2 7 Mounting types . 2 8 Piston rod characteristics . 2 9 Identification statement (reference to this part of ISO

9、6020) 3 Bibliography .20 ISO 2015 All rights reserved iii Contents PageBS ISO 6020-2:2015ISO 6020-2:2015(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is n

10、ormally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part i

11、n the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular

12、 the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this d

13、ocument may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso

14、.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the W

15、TO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 131, Fluid power systems, Subcommittee SC 3, Cylinders. This fourth edition cancels and replaces the third edition (ISO 6020-2:2006

16、), which has been technically revised to incorporate Technical Corrigendum 1, published 2008-10-15. ISO 6020 consists of the following parts, under the general title Hydraulic fluid power Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series: Part 1: Medium series Part 2: Compact ser

17、ies Part 3: Compact series with bores from 250 mm to 500 mmiv ISO 2015 All rights reservedBS ISO 6020-2:2015ISO 6020-2:2015(E) Introduction In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. One component of such systems

18、is the cylinder. This is a device that converts fluid power into linear mechanical force and motion. It consists of a moveable element, i.e. a piston and piston rod, operating within a cylindrical bore. ISO 2015 All rights reserved vBS ISO 6020-2:2015BS ISO 6020-2:2015Hydraulic fluid power Mounting

19、dimensions for single rod cylinders, 16 MPa (160 bar) series Part 2: Compact series 1 Scope This part of ISO 6020 establishes metric mounting dimensions for compact series cylinders, 16 MPa 160 bar 1) , as required for interchangeability of commonly-used hydraulic cylinders. NOTE 1 This part of ISO

20、6020 allows manufacturers of hydraulic equipment flexibility in the design of metric cylinders and does not restrict technical development; however, it does provide basic guidelines. NOTE 2 The compact series dimensions are most applicable to square head cylinders. 2 Normative references The followi

21、ng documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 273, Fasteners

22、 Clearance holes for bolts and screws ISO 3320, Fluid power systems and components Cylinder bores and piston rod diameters and area ratios Metric series ISO 5598, Fluid power systems and components Vocabulary ISO 6099, Fluid power systems and components Cylinders Identification code for mounting dim

23、ensions and mounting types 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 5598 apply. 4 Dimensions 4.1 Mounting dimensions for cylinders manufactured in accordance with this part of ISO 6020 shall be selected from Figures 1 to 13 and Tables 1 to 13.

24、 4.2 Port and flange sizes and dimensions shall be selected from Table 14 and in the respective International Standards cited therein. 4.3 All the dimensions and methods of mounting in this part of ISO 6020 are identified by codes in accordance with ISO 6099. 4.4 Tolerances for mounting dimensions s

25、hall be in accordance with Table 15. 1) 1 bar = 0,1 MPa = 10 5Pa; 1 MPa = 1 N/mm 2 . INTERNATIONAL ST ANDARD ISO 6020-2:2015(E) ISO 2015 All rights reserved 1BS ISO 6020-2:2015ISO 6020-2:2015(E) 5 Bore sizes This part of ISO 6020 includes the following bore sizes, in millimetres, in accordance with

26、ISO 3320: 25 32 40 50 63 80 100 125 160 200. NOTE Mounting dimensions for compact hydraulic single rod cylinders with bores from 250 mm to 500 mm are specified in ISO 6020-3. 6 Piston stroke tolerances The tolerance on piston strokes shall be as follows: piston strokes 1 250 mm: +2/-0 mm; piston str

27、okes 1 250 mm and 3 150: +5/0 mm; piston strokes 3 150 mm and 8 000: +8/0 mm. 7 Mounting types This part of ISO 6020 includes the following mounting types, in accordance with ISO 6099: ME 5 Head, rectangular (see Figure 2 and Table 2) ME 6 Cap, rectangular (see Figure 3 and Table 3) MP 1 Cap, fixed

28、clevis (see Figure 4 and Table 4) MP 3 Cap, fixed plain eye (see Figure 5 and Table 5) MP 5 Cap, fixed eye with spherical bearing (see Figure 6 and Table 6) MS 2 Side lugs (see Figure 7 and Table 7) MT 1 Head, integral trunnion (male) (see Figure 8 and Table 8) MT 2 Cap, integral trunnion (male) (se

29、e Figure 9 and Table 9) MT 4 Intermediate trunnion (male) with selectable position (see Figure 10 and Table 10) MX 1 Both ends studs or tie rods extended (see Figure 11 and Table 11) MX 2 Cap studs or tie rods extended (see Figure 12 and Table 12) MX 3 Head studs or tie rods extended (see Figure 13

30、and Table 13) 8 Piston rod characteristics 8.1 This part of ISO 6020 covers piston rods that have shouldered male thread ends; see Figure 1 and Table 1 for basic dimensions. 8.2 For rod end types, see ISO 4395. 8.3 For accessories, see ISO 8133.2 ISO 2015 All rights reservedBS ISO 6020-2:2015ISO 602

31、0-2:2015(E) 9 Identification statement (reference to this part of ISO 6020) It is strongly recommended to fabricators who elect to conform to this part of ISO 6020 to use the following statement in test reports, catalogues and sales literature: “Interchangeable mounting dimensions selected in accord

32、ance with ISO 6020-2, Hydraulic fluid power Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Part 2: Compact series.”Key a Reference point. b See Table 14 for port options. c Dimensions SF and WL are controlled by ISO 4395. Figure 1 General dimensions ISO 2015 All rights reserve

33、d 3BS ISO 6020-2:2015ISO 6020-2:2015(E) Table 1 General dimensions Dimensions in millimetres Bore Rod MM a KK a A H E Y b PJ c6g max. max. 1,5 25 12 M10 1,25 14 5 40 1,5 50 53 18 M10 1,25 M14 1,5 14 18 32 14 M12 1,25 16 5 45 1,5 60 56 22 M12 1,25 M16 1,5 16 2218 M14 1,5 18 40 22 M14 1,5 M16 1,5 18 2

34、2 63 1,5 62 7328 M14 1,5 M20 1,5 18 2822 M16 1,5 22 50 28 M16 1,5 M20 1,5 22 28 75 1,5 67 7436 M16 1,5 M27 2 22 3628 M20 1,5 28 63 36 M20 1,5 M27 2 28 36 90 1,5 71 8045 M20 1,5 M33 2 28 4536 M27 2 36 80 45 M27 2 M33 2 36 45 115 1,5 77 9356 M27 2 M42 2 36 5645 M33 2 45 100 56 M33 2 M42 2 45 56 130 2

35、82 10170 M33 2 M48 2 45 6356 M42 2 56 125 70 M42 2 M48 2 56 63 165 2 86 11790 M42 2 M64 3 56 8570 M48 2 63 160 90 M48 2 M64 3 63 85 205 2 86 130 aIf other piston rod diameters or other piston rod threads are required, use those identified in ISO 3320 and ISO 4395. bThe tolerance on dimension Y is de

36、pendent on stroke; see Table 15. cThe tolerance on dimension PJ shall be added to the tolerance on the stroke.4 ISO 2015 All rights reservedBS ISO 6020-2:2015ISO 6020-2:2015(E) Bore Rod MM a KK a A H E Y b PJ c6g max. max. 1,5110 M48 2 M80 3 63 9590 M64 3 85 200 110 M64 3 M80 3 85 95 245 2 98 165140

37、 M64 3 M100 3 85 112aIf other piston rod diameters or other piston rod threads are required, use those identified in ISO 3320 and ISO 4395. bThe tolerance on dimension Y is dependent on stroke; see Table 15. cThe tolerance on dimension PJ shall be added to the tolerance on the stroke. Figure 2 ME 5

38、Head, rectangular Table 2 Dimensions of head, rectangular Dimensions in millimetres Bore Rod MM RD OD E TO FB b R WF F VE VL B UO ZB c Hf8 js13 H13 js13 2 max. max. min. max. max. max. 25 12 3840 1,5 51 5,5 27 25 10 16 3 24 65 121 5 1830 32 14 4245 1,5 58 6,6 33 35 10 22 3 26 70 137 5 223418 30 aOD

39、shall be smaller than RD. bHole in accordance with ISO 273, medium series. cThe tolerance for dimension ZB is dependent on stroke; see Table 15.Table 1 (continued) ISO 2015 All rights reserved 5BS ISO 6020-2:2015ISO 6020-2:2015(E) Bore Rod MM RD OD E TO FB b R WF F VE VL B UO ZB c Hf8 js13 H13 js13

40、2 max. max. min. max. max. max. 40 22 6263 1,5 87 11 41 35 10 22 3 34 110 166 28 42 22 34 50 28 7475 1,5 105 14 52 41 16 25 4 42 130 176 36 50 28 75 a42 63 36 8890 1,5 117 14 65 48 16 29 4 50 145 185 45 88 60 36 82 50 80 45 105115 1,5 149 18 83 51 20 29 4 60 180 212 56 105 72 45 92 60 100 56 125130

41、2 162 18 97 57 22 32 5 72 200 225 70 125 88 56 105 72 125 70 150165 2 208 22 126 57 22 32 5 88 250 260 90 150 108 70 125 88 160 90 170205 2 253 26 155 57 25 32 5 108 300 279 110 170 133 90 150 108 200 110 210245 2 300 33 190 57 25 32 5 133 360 336 140 210 163 aOD shall be smaller than RD. bHole in a

42、ccordance with ISO 273, medium series. cThe tolerance for dimension ZB is dependent on stroke; see Table 15.Table 2 (continued) 6 ISO 2015 All rights reservedBS ISO 6020-2:2015ISO 6020-2:2015(E)Figure 3 ME 6 Cap, rectangular Table 3 Dimensions of cap, rectangular Dimensions in millimetres Bore E TO

43、FB a R ZJ b UO Hjs13 H13 js13 max. max. 25 40 1,5 51 5,5 27 114 65 5 32 45 1,5 58 6,6 33 128 70 5 40 63 1,5 87 11 41 153 110 50 75 1,5 105 14 52 159 130 63 90 1,5 117 14 65 168 145 80 115 1,5 149 18 83 190 180 100 130 2 162 18 97 203 200 125 165 2 208 22 126 232 250 160 205 2 253 26 155 245 300 200

44、245 2 300 33 190 299 360 aHole in accordance with ISO 273, medium series. bThe tolerance on dimension ZJ is dependent on stroke; see Table 15. ISO 2015 All rights reserved 7BS ISO 6020-2:2015ISO 6020-2:2015(E) Figure 4 MP 1 Cap, fixed clevis Table 4 Dimensions of cap, fixed clevis Dimensions in mill

45、imetres Bore CB CD MR L UB XC aA13 H9 max. min. max. 25 12 10 12 13 25 127 32 16 12 17 19 34 147 40 20 14 17 19 42 172 50 30 20 29 32 62 191 63 30 20 29 32 62 200 80 40 28 34 39 83 229 100 50 36 50 54 103 257 125 60 45 53 57 123 289 160 70 56 59 63 143 308 200 80 70 78 82 163 381 aThe tolerance on d

46、imension XC is dependent on stroke; see Table 15.8 ISO 2015 All rights reservedBS ISO 6020-2:2015ISO 6020-2:2015(E)Figure 5 MP 3 Cap, fixed plain eye Table 5 Dimensions of cap, fixed plain eye Dimensions in millimetres Bore EW CD MR L XC ah14 H9 max. min. 25 12 10 12 13 127 32 16 12 17 19 147 40 20

47、14 17 19 172 50 30 20 29 32 191 63 30 20 29 32 200 80 40 28 34 39 229 100 50 36 50 54 257 125 60 45 53 57 289 160 70 56 59 63 308 200 80 70 78 82 381 aThe tolerance on dimension XC is dependent on stroke; see Table 15. ISO 2015 All rights reserved 9BS ISO 6020-2:2015ISO 6020-2:2015(E)Figure 6 MP 5 C

48、ap, fixed eye with spherical bearing Table 6 Dimensions on cap, fixed eye with spherical bearing Dimensions in millimetres Bore EP EX CX MS LT XO a Zmax. nom. tol. nom. tol. max. min. min. 25 8 10 0 0,12 12 0 0,008 20 16 13032 11 14 0 0,12 16 0 0,008 22,5 20 14840 13 16 0 0,12 20 0 0,012 29 25 17850 17 20 0 0,12 25 0 0,012 33 31 19063 19 22 0 0,12 30 0 0,012 40 38 206 3 80 23 28 0 0,12 40 0 0,012 50 48 238100 30 35 0 0,12 50 0 0,0