IEC 60300-3-15-2009 Dependability management - Part.3-15 Application guide - Engineering of system dependability《可靠性管理 第3-15部分 应用指南 系统可靠性技术》.pdf

《IEC 60300-3-15-2009 Dependability management - Part.3-15 Application guide - Engineering of system dependability《可靠性管理 第3-15部分 应用指南 系统可靠性技术》.pdf》由会员分享，可在线阅读，更多相关《IEC 60300-3-15-2009 Dependability management - Part.3-15 Application guide - Engineering of system dependability《可靠性管理 第3-15部分 应用指南 系统可靠性技术》.pdf（124页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60300-3-15 Edition 1.0 2009-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Dependability management Part 3-15: Application guide Engineering of system dependability Gestion de la sret de fonctionnement Partie 3-15: Guide dapplication Ingnierie de la sret de fonctionnement des systmes IEC 60300-

2、3-15:2009 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2009 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without pe

3、rmission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee

4、for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI o

5、u du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office

6、3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About I

7、EC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to

8、search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new pub

9、lications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as th

10、e International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41

11、22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu techniqu

12、e des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des reche

13、rches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille d

14、eux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les term

15、es quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Se

16、rvice clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 60300-3-15 Edition 1.0 2009-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Dependability management Part 3-15: Application guide Engineering of system dependability Gestion de la sret de fonctionnement

17、Partie 3-15: Guide dapplication Ingnierie de la sret de fonctionnement des systmes INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE XA ICS 03.120.01 PRICE CODE CODE PRIX ISBN 2-8318-1048-4 Registered trademark of the International Electrotechnical Commission Marqu

18、e dpose de la Commission Electrotechnique Internationale 2 60300-3-15 IEC:2009 CONTENTS FOREWORD.4 INTRODUCTION.6 1 Scope.7 2 Normative references .7 3 Terms and definitions .7 4 System dependability engineering and applications8 4.1 Overview of system dependability engineering 8 4.2 System dependab

19、ility attributes and performance characteristics 9 5 Managing system dependability10 5.1 Dependability management .10 5.2 System dependability projects .10 5.3 Tailoring to meet project needs .11 5.4 Dependability assurance .11 6 Realization of system dependability11 6.1 Process for engineering depe

20、ndability into systems.11 6.1.1 Purpose of dependability process 11 6.1.2 System life cycle and processes11 6.1.3 Process applications through the system life cycle 12 6.2 Achievement of system dependability14 6.2.1 Purpose of system dependability achievements.14 6.2.2 Criteria for system dependabil

21、ity achievements .14 6.2.3 Methodology for system dependability achievements.15 6.2.4 Realization of system functions .16 6.2.5 Approaches to determine achievement of system dependability.17 6.2.6 Objective evidence of achievements18 6.3 Assessment of system dependability .18 6.3.1 Purpose of system

22、 dependability assessments 18 6.3.2 Types of assessments .18 6.3.3 Methodology for system dependability assessments20 6.3.4 Assessment value and implications .21 6.4 Measurement of system dependability.21 6.4.1 Purpose of system dependability measurements .21 6.4.2 Classification of system dependabi

23、lity measurements22 6.4.3 Sources of measurements .23 6.4.4 Enabling systems for dependability measurements23 6.4.5 Interpretation of dependability measurements24 Annex A (informative) System life cycle processes and applications 25 Annex B (informative) Methods and tools for system dependability de

24、velopment and assurance.35 Annex C (informative) Guidance on system application environment42 Annex D (informative) Checklists for System Dependability Engineering47 Bibliography54 Figure 1 An overview of a system life cycle12 Figure 2 An example of a process model .13 60300-3-15 IEC:2009 3 Figure A

25、.1 An overview of system life cycle processes.25 Figure C.1 Environmental requirements definition process.43 Figure C.2 Mapping system application environments to exposures .44 4 60300-3-15 IEC:2009 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ DEPENDABILITY MANAGEMENT Part 3-15: Application guide Eng

26、ineering of system dependability FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions

27、concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”).

28、 Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collabora

29、tes closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on th

30、e relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure tha

31、t the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the m

32、aximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication should be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered respon

33、sible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability should attach to IEC or its directors, employees, servants or agents including individual experts and members of its technic

34、al committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Pu

35、blications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject

36、of patent rights. IEC should not be held responsible for identifying any or all such patent rights. International Standard IEC 60300-3-15 has been prepared by IEC technical committee 56: Dependability. The text of this standard is based on the following documents: FDIS Report on voting 56/1315/FDIS

37、56/1321/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 60300-3-15 IEC:2009 5 A list of all parts of the IEC 60300 series, unde

38、r the general title Dependability management, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publi

39、cation. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 6 60300-3-15 IEC:2009 INTRODUCTION Systems are growing in complexity in todays application environments. System dependability has become an important performance attribute that affects th

40、e business strategies in system acquisition and the cost-effectiveness in system ownership and operations. The overall dependability of a system is the combined result of complex interactions of system elements, application environments, human-machine interfaces, deployment of support services and o

41、ther influencing factors. This part of IEC 60300 gives guidance on the engineering of the overall system to achieve its dependability objectives. The engineering approach in this standard represents the application of appropriate scientific knowledge and relevant technical disciplines for realizing

42、the required dependability for the system of interest. The four main aspects for engineering dependability concerning systems are addressed in terms of process, achievement, assessment, and measurement. The engineering disciplines consist of technical processes that are applicable to the various sta

43、ges of the system life cycle. Specific technical processes described in this part of IEC 60300 are supported by a sequence of relevant process activities to achieve the objectives of each system life cycle stage. This part of IEC 60300 is applicable to generic systems with interacting system functio

44、ns consisting of hardware, software and human elements to achieve system performance objectives. In many cases a function can be realized by commercial off-the-shelf products. A system can link to other systems to form a network. The boundaries separating a product from a system, and a system from a

45、 network, can be distinguished by defining the application of the entity. For example, a digital timer as a product can be used to synchronize the operation of a computer; the computer as a system can be linked with other computers in a business office for communications as a local area network. The

46、 application environment is applicable to all kinds of systems. Examples of applicable systems include control systems for power generation, fault-tolerant computing systems and systems for provision of maintenance support services. Guidance on dependability engineering is provided for generic syste

47、ms. It does not classify systems for special applications. The majority of systems in use are generally repairable throughout their life cycle operation for economic reasons and practical applications. Non- repairable systems such as communication satellites, remote sensing/monitoring equipment, and

48、 one-shot devices are considered as application-specific systems. They require further identification of specific application environment, operational conditions and additional information on unique performance characteristics to achieve their mission success objectives. Non-repairable subsystems an

49、d components are considered as throwaway items. The selection of applicable processes for engineering dependability into a specific system is carried out through the project tailoring and dependability management process. This part of IEC 60300 forms part of the framework standards on system aspects of dependability to support IEC 60300-1 and IEC 60300-2 on dependability management. References ar